Posted: Thu Apr 20, 2023 4:41 Post subject: New Build - 04/20/2023 - r52369
Welcome to Marvell r52369 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
List router model & version or revision, operating & wireless modes & exact filename/firmware image flashed.
CLI Flash: 'cd /tmp' then 'wget {file URL}' (httponly) or 'curl -O {file URL}' (http, https, ftp). 'write {file} linux' then 'reboot'.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Update 5/13/23 - I had to fall back to 51937 shortly after my 4/26 update after experiencing disconnects and/or problems connecting.
Update: 4/26/23 - This release has been running great for me the last ~4 days since disabling 802.11r FT.
Similar wifi connection hang on my 3200ACM as I have been seeing on various releases post-r51937. My iphone and macbook were both connected to the 5ghz radio on the 3200 about 3 feet away. Both stopped passing data at the same time. I had a ping running on the macbook and noticed it stop pinging the router. My wife's iphone had roamed onto the router for a few minutes prior and then roamed away, and this is exactly when the pings started timing out on my macbook. I pulled up a browser on my iphone (which was just sitting on the desk asleep) and couldn't get to the internet. Turned off the wifi on my iphone and my macbook started pinging again. Turned on the wifi on my iphone and it connected again. No messages in dmesg or the logs other than the devices reconnecting to wifi. I'll probably go back to 51937 (3/05/23) which was prior to the new mwlwifi (see https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=334152.)
Router Model & Version: Linksys 3200ACM and 1900ACSv1
Firmware: 52369 (04/20/23)
Previous: 51937 (03/05/23)
Reset: No
Mode: AP / Gateway (3200ACM), Router
Uptime: 3 hours
Status: Performance is great when the wifi connection is working
Issues/Errors: When several devices go to sleep or roam in/out of the range of the route, wifi stays connected but traffic just freezes on multiple device until wifi is turned off on one of the affected devices
Environment: 5gh radio: AC/N mixed, Wide HT40, channel 44U, beacon 100, dtim 2, WPA2-personal AES, WPA strict rekey on, 802.11r on
syslog:
ca:cf:38:49:8a:40 - my wife's iphone roaming around prior to outage
5a:3b:c6:54:15:8d - my iphone
f0:18:98:6a:3d:e1 - my macbook
09:53:14 - wife's iphone roams away - I can confirm that this is the exact second my latop stopped pinging. 09:54:55 - turned off wifi on my iphone
09:54:57 - macbook starts pinging again
Router Model Linksys WRT1900ACS v2
Firmware Version DD-WRT v3.0-r52369 std (04/20/23)
Kernel Version Linux 4.9.337 #3757 SMP Thu Apr 20 01:10:00 +07 2023 armv7l
Current Time Sun, 23 Apr 2023 21:50:24
Uptime 13 min
update-browser waterfox, I switched from partion 1, linksys firmware
connection Type PPPoE - IPv6 Type DHCPv6 with Prefix Delegation 1Gbps
IPv6 Type DHCPv6 with Prefix Delegation-On - Ok
Operating Mode Gateway/AP
Shortcut Forwarding Engine-On
Schedule Reboot-On,
Web Access Protocol - HTTPS,
SSH (public key)-ok
Validate DNS Replies (DNSSEC)-ok
Port Forwarding - Ok,
USB - System Log -Ok
Schedule Reboot - At a Set Time - On
After configuring the settings, I rebooted the router every time!
Wireless Interface 5GHz-Wireless Mode AP-Wireless Network Mode-AC, Width VHT 80 Mhz-Wireless Channel-36,Extension Channel UU, Short GI, Short Preamble, Single User Beamforming, Radio Scheduling, 30TX Power-30dBm ,TX Antenna Chains-1+2+3+4, RX Antenna Chains-1+2+3+4, Enable-WPA2 Personal-CCMP-128 (AES), Regulatory Domain Romania, all-ok
I see that this problem still persists, no one took it into account, after switching from linksys firmware to ddwrt, the router no longer knows how to switch to ddwrt, only after pressing the power button it returns to normal _________________ Internet provider https://en.wikipedia.org/wiki/RCS_%26_RDS 1Gbps
WDR3600 rev.1.5 - DD-Wrt
Linksys WRT1900ACS v.2 DD-Wrt/-OpenWrt
[quote="kosmos"]hello, try this in your custom config[/quote]
thanks for the suggestion. I already had ap_max_inactivity=600 in my custom config. Increasing it to 3600 didn't help. However turning off 802.11r FT on my routers did fix the problem - no wifi freezes in 1+ days. I'm not sure how much good 802.11r was doing me anyways - probably best to leave it off.
WIFI has been excellent the last day or so. I noticed a 2018 Samsung TV that didn't like marvel wifi - using mac address blacklisting to push it to choose a netgear 7800 fixed that problem - not sure if this existed on r51937 and before or not.
Joined: 12 Dec 2007 Posts: 780 Location: Pittsburgh, PA USA
Posted: Tue Apr 25, 2023 17:22 Post subject:
Router/Version: WRT1900AC v1
File/Kernel: DD-WRT v3.0-r52369 std (04/20/23)
Previous/Reset: DD-WRT v3.0-r52306 std (04/11/23). No reset this time.
Mode/Status: Gateway (SFE enabled), Access Point, IPV6 (DHCP6 w/ prefix delegation), Entware, DOT via SmartDNS/DNSMasq, OpenVPN server, Wireguard Server
Issues/Errors:
Up 5 days. Wireless and wired speeds are as expected. OpenVPN and Wireguard both working normally. The issue I reported on the last build turned out not to be WiFi related at all, it was Bluetooth. _________________ __________________________
Netgear R7800
DD-WRT v3.0 STD
Linksys WRT1900AC
DD-WRT v3.0 STD
The other bugs are wan type connection about PPTP and PPTP Server.
Wan Type Connection about PPTP
It causes router breaking in WRT32X. Reset function did not work. It needs a long time (hourly). The router would resume the default mode automatically.
PPTP Server
Instagram, facebook and youtube could not load the picture and video smoothly! Especially, android user. That is not security issue. Please fix it immediately!
kosmos wrote:
what does this message mean exactly? Is this a crash message from the physical WLAN interface? I have this several times a day.
From the times it looks to me as if that happens when a participant becomes active.