Posted: Sat Apr 08, 2023 5:01 Post subject: New Build - 04/08/2023 - r52242
Welcome to Marvell r52242 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
List router model & version or revision, operating & wireless modes & exact filename/firmware image flashed.
CLI Flash: 'cd /tmp' then 'wget {file URL}' (httponly) or 'curl -O {file URL}' (http, https, ftp). 'write {file} linux' then 'reboot'.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Similar wifi connection hang on my 3200ACM as I have been seeing since I first noticed it with 52054. My iphone and macbook were both connected to the 5ghz radio on the 3200 about 3 feet away. Both stopped passing data at the same time. I had a ping running on the macbook and noticed it stop pinging the router. I pulled up a browser on my iphone (which was just sitting on the desk asleep) and couldn't get to the internet. Recycled wifi on iphone and both devices started working again. No messages in the logs other than the devices reconnecting to wifi. This has happened twice today since upgrading about 12 hours ago. I may drop back down to 51729 (2/16/23) or maybe try 51937 (3/05/23) which others have reported as a good fallback release prior to a lot of changes.
Router Model & Version: Linksys 3200ACM
Firmware: 52242 (04/08/23)
Previous: 52217 (04/02/23) (noticed the issue several times with this release too on several different devices.)
Reset: No
Mode: AP / Gateway (3200ACM), Router
Uptime: 12 hours
Status: Performance is good when the wifi connection is working
Issues/Errors: Wifi stays connected but traffic just freezes - nothing in dmesg or syslog.
Environment: 5gh radio: AC/N mixed, Wide HT40, channel 44U, beacon 100, dtim 2, WPA2-personal AES, WPA strict rekey on, 802.11r on
Joined: 14 Dec 2015 Posts: 775 Location: 127.0.0.1
Posted: Sun Apr 09, 2023 4:40 Post subject: Long time. What browser?
I know, been a long time, how you all doing.
I was trying to go from a September build to this one, on a wrt1200acv1, web upgrade. Took a while, now its working except I can't get into the GUI. I do get warnings on chrome, firefox, brave, yet when I try to continue it just sits there.
Its on a secondary network, so I am not that concerned right now. I know all the devices are working and still connected to it. _________________ Tutorial for flashing WRT series WRT Installation,Upgrade & Basic Setup–Cliff Notes
r52242: WRT3200ACM, WRT1200ACv1 & 1 Velop in bridge mode(IoT subnet), r52242 WRT1900ACv1 AP
Velop:2 WHW0101, RE6500, RE9000(AP)
Spectrum - 1000/50
SysLog Watcher 5, New security Onion box coming soon, Fingboxes, PiHoles, NEMS, Cacti, rpisurv
Joined: 14 Dec 2015 Posts: 775 Location: 127.0.0.1
Posted: Sun Apr 09, 2023 8:16 Post subject:
I got it to the new build. Forgot to reset it do default. loaded the old settings backup, and everything is working okay. _________________ Tutorial for flashing WRT series WRT Installation,Upgrade & Basic Setup–Cliff Notes
r52242: WRT3200ACM, WRT1200ACv1 & 1 Velop in bridge mode(IoT subnet), r52242 WRT1900ACv1 AP
Velop:2 WHW0101, RE6500, RE9000(AP)
Spectrum - 1000/50
SysLog Watcher 5, New security Onion box coming soon, Fingboxes, PiHoles, NEMS, Cacti, rpisurv
Router Model Linksys WRT1900ACS v2
Firmware Version DD-WRT v3.0-r52242 std (04/08/23)
Kernel Version Linux 4.9.337 #3739 SMP Sat Apr 8 02:41:54 +07 2023 armv7l
Current Time Sun, 09 Apr 2023 15:31:32
Uptime 16:30
update-browser waterfox, I switched from partition one linksys firmwarethe router stopped responding to ping until I rebooted it from the power button
connection Type PPPoE - IPv6 Type DHCPv6 with Prefix Delegation 1Gbps
IPv6 Type DHCPv6 with Prefix Delegation-On - Ok
Operating Mode Gateway/AP
Shortcut Forwarding Engine-On
Schedule Reboot-On,
Web Access Protocol - HTTPS,
SSH (public key)- ok
Port Forwarding - Ok,
USB - System Log -Ok
Schedule Reboot - At a Set Time - On[/color]
After configuring the settings, I rebooted the router every time!
Wireless Interface 5GHz-Wireless Mode AP-Wireless Network Mode-AC, Width VHT 80 Mhz-Wireless Channel-36,Extension Channel UU, Short GI, Short Preamble, Single User Beamforming, Radio Scheduling, TX Power-30Bm ,TX Antenna Chains-1+2+3+4, RX Antenna Chains-1+2+3+4, Enable-WPA2 Personal-CCMP-128 (AES), Regulatory Domain Romania
the wifi part works, but after half an hour of watching movies on netflix, HBO loses the signal, or as if the internet no longer works on that device, I did not notice this problem on Openwrt, which I recently tested
if I have Vlans Enable in speed test on the wire no longer exceeds 890 Mbps download upload, after disabling 935 Mbps _________________ Internet provider https://en.wikipedia.org/wiki/RCS_%26_RDS 1Gbps
WDR3600 rev.1.5 - DD-Wrt
Linksys WRT1900ACS v.2 DD-Wrt/-OpenWrt
GL-MT6000 OpenWrt
So activating the "switch config tab" does not cause the LAN ports to stop working?
So the problem is fixed.
Who wants can test the tab now extensively.
I have posted examples for routers with 2 CPU ports under the following link
there are no more disconnections, but I noticed a slight decrease in the speed test!
What can VLAN Configuration help me with? _________________ Internet provider https://en.wikipedia.org/wiki/RCS_%26_RDS 1Gbps
WDR3600 rev.1.5 - DD-Wrt
Linksys WRT1900ACS v.2 DD-Wrt/-OpenWrt
GL-MT6000 OpenWrt
The speed loss is not relevant, this may be a measurement inaccuracy and BS had written to me that VLAN on the Marvel platform requires some resources.
I don't know how VLANs can help you.
but matjazk has configured his router e.g. as WAP and a WAP does not need a WAN port.
under the link is an example of how to add the WAN port to the LAN.
The speed loss is not relevant, this may be a measurement inaccuracy and BS had written to me that VLAN on the Marvel platform requires some resources.
I don't know how VLANs can help you.
but matjazk has configured his router e.g. as WAP and a WAP does not need a WAN port.
under the link is an example of how to add the WAN port to the LAN.
I tried to make the settings from the first image and I don't have more than 10mbps on the wire
If I want to return to the default Vlans configuration, the internet stops working and wifi is activated again _________________ Internet provider https://en.wikipedia.org/wiki/RCS_%26_RDS 1Gbps
WDR3600 rev.1.5 - DD-Wrt
Linksys WRT1900ACS v.2 DD-Wrt/-OpenWrt
GL-MT6000 OpenWrt
The first screenshot in the thread shows the default setting?
They are not different on your Marvel router?
And shortly before you wrote that you had a throughput of 890Mbit after activating the "switch config tab".
The first screenshot in the thread shows the default setting?
They are not different on your Marvel router?
And shortly before you wrote that you had a throughput of 890Mbit after activating the "switch config tab".
Sorry, I was referring to the second image, but!
it seems that after I deactivated it and activated it on the default settings, the internet works again! _________________ Internet provider https://en.wikipedia.org/wiki/RCS_%26_RDS 1Gbps
WDR3600 rev.1.5 - DD-Wrt
Linksys WRT1900ACS v.2 DD-Wrt/-OpenWrt
GL-MT6000 OpenWrt