Joined: 18 Mar 2014 Posts: 12884 Location: Netherlands
Posted: Mon Mar 27, 2023 12:21 Post subject:
Router Model: Linksys EA8500
Firmware Version: DD-WRT v3.0-r52148M Community Build by EGC (03/26/23)
Upgraded from: DD-WRT v3.0-r52054M Community Build by EGC (03/18/23)
Reset: No not this time
Status: Up and running for 24 hours, basic setup as Gateway, static leases, 2.4 GHz and 5 GHz switched off, OpenVPN server working, WireGuard Server working (multiple clients e.g. phone, laptop and site-to-site connection with remote location), NAS and Samba working, Avahi and Avahi-utils working.
IPv6 working
Errors: Nothing encountered at this moment, the new Switch config tab is looking good.
Router/Version: Netgear XR500
Update method:WebUpgrade
File/Kernel: dd-wrt-webupgrade.bin / Linux 4.9.337 #1735 SMP Sun Mar 26 03:21:55 +07 2023 armv7l
Previous/Reset: r52095 / no
Mode/Status: Gateway / Up and running for 6:22 hours
Issues/Errors: Nothing significant
____________________________________________________________________________
Router/Version: TP-Link WDR4900 V1
File/Kernel: tl-wdr4900-webflash.bin / Linux 4.4.302-st38 #3129 Sun Mar 26 02:45:13 +06 2023 ppc
Previous/Reset: r51935 / no
Mode/Status: Gateway / Up and running for 6:16 hours
Issues/Errors: Nothing significant
_______________________________________________________________________________________________
Router/Version: TP-Link TL-WR841ND v11
Update method: WebUpgrade
File/Kernel: tl-wr841nd-webflash.bin / Linux 3.18.140-d6 #167613 Sun Mar 26 06:27:40 +06 2023 mips
Previous/Reset: r52095 / no
Mode/Status: AP wired and wireless / Up and running for 6:01 hours
Issues/Errors: Nothing significant
The fact is that the router connected to the Internet (to the Internet provider). And it reports an error, the orange WAN indicator flashes (the icon in the form of a planet). Internet is working, I just think it's a glitch
Thank you BS and gurus! _________________ Atheros
Netgear XR500 Nighthawk - DD-WRT 54545
Tp-Link TL-WDR4900 v1.3 - DD-WRT 53133
TP-Link WR1043ND v4 - DD-WRT 51838
TP-Link WR1043ND v2 - Gargoyle OS 1.13.0
TP-Link WR841ND v11 - DD-WRT 55779
Broadcom
Asus RT-AC87U R - DD-WRT 55819
Asus RT-N66U - DD-WRT 55779
Linksys WRT54GL v1.1 - DD-WRT 54517M
Linksys WRT54GL v1.1 - FreshTomato 2023.4_MIPS_K26
Linksys WRT54GL v1.1 - Gargoyle OS 1.6.2
Joined: 06 Jun 2006 Posts: 7492 Location: Dresden, Germany
Posted: Mon Mar 27, 2023 17:55 Post subject:
matjazk wrote:
@ho1Aetoo
I know that the switch config tab is not working for R9000, and I did not attempt to do anything. Simply clicking on the tab caused httpd to crash - before anything is shown in the browser (I tried both Firefox and Pale Moon, although this probably has nothing to do with the crash).
this crashlog is not from the switch page. but in any way. i know that the switch page on the r9000 wasnt working in last build. but its already fixed. but it shows just the port static. the switch is not yet configurable like in the past _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
Update method: Web
Router/Version: TPLink TL-WR841ND v9
File/Kernel: DD-WRT v3.0-r52148 std (03/26/23)
Previous/Reset: DD-WRT v3.0-r52095 std (03/23/23) / No
Mode/Status: Gateway / Working Normally*
Issues/Errors:
Enabling wireguard causes router to hang.
Router still advertises SSID, however stops responding to all traffic (putty/web/dhcp etc)
No peers added, just simple enabling of the wireguard.
Logs end with
vpn modules successfully loaded
Manual wireguard configuration via scripts does not cause the same effect and wireguard functions properly.
Perhaps something with unloading/reloading modules during config change.
No ability to connect UART to see console output and logging is severely limited due to 4/32 i presume
Joined: 18 Mar 2014 Posts: 12884 Location: Netherlands
Posted: Tue Mar 28, 2023 8:23 Post subject:
andlommy wrote:
Update method: Web
Router/Version: TPLink TL-WR841ND v9
File/Kernel: DD-WRT v3.0-r52148 std (03/26/23)
Previous/Reset: DD-WRT v3.0-r52095 std (03/23/23) / No
Mode/Status: Gateway / Working Normally*
Issues/Errors:
Enabling wireguard causes router to hang.
Router still advertises SSID, however stops responding to all traffic (putty/web/dhcp etc)
No peers added, just simple enabling of the wireguard.
Logs end with
vpn modules successfully loaded
Manual wireguard configuration via scripts does not cause the same effect and wireguard functions properly.
Perhaps something with unloading/reloading modules during config change.
No ability to connect UART to see console output and logging is severely limited due to 4/32 i presume
Are you sure it was working in 52095, because there have been no WG changes between 52095 and 52148 as far as I can tell.
Mostly changes regarding the Switch config tab and vlans.
Maybe the changes let this little 4/32 MB router fall of the memory cliff?
