Posted: Sun Mar 26, 2023 14:47 Post subject: New Build - 03/26/2023 - r52148
Welcome to Marvell r52148 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
List router model & version or revision, operating & wireless modes & exact filename/firmware image flashed.
CLI Flash: 'cd /tmp' then 'wget {file URL}' (httponly) or 'curl -O {file URL}' (http, https, ftp). 'write {file} linux' then 'reboot'.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Router/Version: Linksys WRT32X
File/Kernel: DD-WRT v3.0-r52148 std (03/26/23)/Linux 4.9.337 #3709 SMP Sun Mar 26 03:45:36 +07 2023 armv7l
Previous/Reset: 03-14-2023-r52020/
Mode/Status: AP only
Issues/Errors: upgrade via web browser without reset. Uptime 1hr. So far so good.
ESP8266 is able to connect without problem under N/G mixed,RTS/CTS protection mode with WMM disable.
Router Model Linksys WRT1900ACS v2
Firmware Version DD-WRT v3.0-r52148 std (03/26/23)
Kernel Version Linux 4.9.337 #3709 SMP Sun Mar 26 03:45:36 +07 2023 armv7l
Current Time Sun, 26 Mar 2023 21:36:50
Uptime 20 min
update-browser waterfox, I switched from partition one on the linksys firmware, all ok
connection Type PPPoE - IPv6 Type DHCPv6 with Prefix Delegation 1Gbps
IPv6 Type DHCPv6 with Prefix Delegation-On - Ok
Operating Mode Gateway/AP
Shortcut Forwarding Engine-On
Schedule Reboot-On,
Web Access Protocol - HTTPS,
SSH (public key)-ok
Encrypt DNS Enable
Validate DNS Replies (DNSSEC)-ok
Port Forwarding - Ok,
USB - System Log -Ok
Schedule Reboot - At a Set Time - On
After configuring the settings, I rebooted the router every time!
Wireless Interface 5GHz-Wireless Mode AP-Wireless Network Mode-AC, Width VHT 80 Mhz-Wireless Channel-36,Extension Channel LL, Short GI, Short Preamble, Single User Beamforming, Radio Scheduling, 30TX Power-30dBm ,TX Antenna Chains-1, RX Antenna Chains-1, Enable-WPA2 Personal-CCMP-128 (AES), Regulatory Domain Romania
Errors: After the update immediate, the router no longer responded to ping and only after a router reboot did I have access and the second reply of losing access came after I changed the access address to the router and again I had to access the button power to reboot the router!
on the wifi side, only disconnections, it is inoperable! _________________ Internet provider https://en.wikipedia.org/wiki/RCS_%26_RDS 1Gbps
WDR3600 rev.1.5 - DD-Wrt
Linksys WRT1900ACS v.2 DD-Wrt/-OpenWrt
Joined: 21 Aug 2019 Posts: 120 Location: Here, There And Everywhere
Posted: Sun Mar 26, 2023 21:40 Post subject:
Router/Version: Linksys WRT1200AC
File/Kernel: DD-WRT v3.0-r52148 std (03/26/23) / Linux 4.9.337 #3709 SMP Sun Mar 26 03:45:36 +07 2023 armv7l
Previous/Reset: r52095 / No
Mode/Status: WAP, USB, NAS / Working
Issues/Errors: Nothing so far. Seems to work perfectly fine.
and "TX Antenna Chains-1, RX Antenna Chains-1" means that the router has only one antenna
no idea if the setting works on Marvel routers but it should not be 1 but 1+2+3+4
Which settings are available for selection?
The setting was probably added by your patch request.
I installed this build yesterday, but had no time to extensively test it on my 1900 ACSv2, yet.
Looking forward to this evening or tomorrow.
So far... everything is working, no hiccups of any kind.
Ok, I disabled WiFi years ago, since it was shit and never enabled it again, therefore no WiFi tests.
After flash the device rebooted and everything was fine.
Gateway, SFE enabled, Wifi disabled, Wireguard for external access, WAN to DSL Modem, samba to access USB3-ext4 SSD, Keep Alive reboot 5:00 in the morning.
and "TX Antenna Chains-1, RX Antenna Chains-1" means that the router has only one antenna
no idea if the setting works on Marvel routers but it should not be 1 but 1+2+3+4
Which settings are available for selection?
TX Antenna Chains
RX Antenna Chains
1+2,3,
The setting was probably added by your patch request.
