EA8500
(This router has ran perfectly before with r49838 on it)
GUI installed r52095 over stock Linksys firmware.
Rebooted, changed credentials, reset to factory defaults for good measure, rebooted again.
Everything seemed OK until I activated the vlan configuration page and rebooted.
DHCP then refuses to assign an IP to the wired connection but works fine on the wireless connection.
I am no expert but the br0 bridging table also doesn't look quite right after vlan is activated.
I am running MX Linux (based on Debian stable) on my PC if that matters.
Joined: 18 Mar 2014 Posts: 12887 Location: Netherlands
Posted: Fri Mar 24, 2023 7:06 Post subject:
hf74 wrote:
EA8500
(This router has ran perfectly before with r49838 on it)
GUI installed r52095 over stock Linksys firmware.
Rebooted, changed credentials, reset to factory defaults for good measure, rebooted again.
Everything seemed OK until I activated the vlan configuration page and rebooted.
DHCP then refuses to assign an IP to the wired connection but works fine on the wireless connection.
I am no expert but the br0 bridging table also doesn't look quite right after vlan is activated.
I am running MX Linux (based on Debian stable) on my PC if that matters.
3. But this will change soon, because the switch config tab gets configurable CPU ports
this is slowly becoming igorant
if you still don't believe me:
1. create a nvram backup (yes a backup has always been able to restore the previous port configuration)
2. activate the "switch config" tab
3. disable the "switch config" tab
4. you now have a backup you don't need
this will take max 5min
I am only the modest person who had requested the function
Joined: 03 Nov 2015 Posts: 317 Location: Florida, USA
Posted: Fri Mar 24, 2023 21:55 Post subject:
Router: Linksys ea8500 ..WDS AP
Firmware: DD-WRT v3.0-r52095 std (03/23/23)
Kernel: Linux 4.9.337 #1714 SMP Thu Mar 23 03:11:42 +07 2023 armv7l
Reset: NO ....GUI upgrade from r52054
Mode: 2.4 GHz only ....Firmware type .. DD-WRT
Errors: None
Router: Linksys ea8500 ..WDS Stations ... X (2)
Firmware: DD-WRT v3.0-r52095 std (03/23/23)
Kernel: Linux 4.9.337 #1714 SMP Thu Mar 23 03:11:42 +07 2023 armv7l
Reset: NO ....GUI upgrade from r52054
Mode: 2.4 GHz only ....Firmware type .. DD-WRT
Errors: None
Everything working right for me .... Logs look about the same as last build .... GOOD
THANKS to ALL !! _________________ ......All GOOD here... Just Handshakes and Time Stamps !......
[quote="hf74"][b]EA8500[/b]
(This router has ran perfectly before with r49838 on it)[/quote]
I'm using that version now, any reason I shouldn't upgrade to r52095? Most important things to me are stability (no random reboots) and 5Ghz signal strength/range/low latency.
Router/Version: Linksys E2100L
File/Kernel: Linux 3.5.7-svn20625 #4941 Mon Feb 11 05:27:12 CET 2013 mips
Previous/Reset: GUI install over DD-WRT v24-sp2 (02/11/13) std - build 20675 / No reset
Mode/Status: Gateway / Router Bricked Issues/Errors: Power led blinks forever, no PING response or web access. Attempted 30/30/30 reset - no change.
Recovered by pushing previous firmware via tftp while connected to separate switch.
Posted: Sun May 14, 2023 1:39 Post subject: TP-Link TL-WR1043ND v1.8
Router Model:TP-Link TL-WR1043ND v1.8 Firmware Version: DD-WRT v3.0-r52095 std (03/23/23)
Previous: DD-WRT v3.0-r51855 std (02/25/23)
File: tl-wr1043nd-webflash.bin
Kernel Version: Linux 3.10.108-d11
Mode: Gateway/AP
Reset: None required
Status: OK
Uptime: ~20 Days
Issues/Errors: Nothing new to report. The webUI is really snappy and stable 🤘💥🔥✔👍
... catching up on back-logged flash reports <grin> _________________ "The woods are lovely, dark and deep,
But I have promises to keep,
And miles to go before I sleep,
And miles to go before I sleep." - Robert Frost
"I am one of the noticeable ones - notice me" - Dale Frances McKenzie Bozzio
