Posted: Sat Mar 18, 2023 6:36 Post subject: New Build - 03/18/2023 - r52054
Welcome to Marvell r52054 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
List router model & version or revision, operating & wireless modes & exact filename/firmware image flashed.
CLI Flash: 'cd /tmp' then 'wget {file URL}' (httponly) or 'curl -O {file URL}' (http, https, ftp). 'write {file} linux' then 'reboot'.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Router Model Linksys WRT1900ACS v2
Firmware Version DD-WRT v3.0-r52054 std (03/18/23)
Kernel Version Linux 4.9.337 #3695 SMP Sat Mar 18 04:32:26 +07 2023 armv7l
Uptime 10:35
update-browser waterfox, I switched from version r52004 without saving settings, all ok
connection Type PPPoE - IPv6 Type DHCPv6 with Prefix Delegation 1Gbps
IPv6 Type DHCPv6 with Prefix Delegation-On - Ok
Operating Mode Gateway/AP
Shortcut Forwarding Engine-On
Schedule Reboot-On,
Web Access Protocol - HTTPS,
SSH (public key)-ok
Validate DNS Replies (DNSSEC)-ok
Port Forwarding - Ok,
USB - System Log -Ok
Schedule Reboot - At a Set Time - On
After configuring the settings, I rebooted the router every time!
Wireless Interface 5GHz-Wireless Mode AP-Wireless Network Mode-AC, Width VHT 80 Mhz-Wireless Channel-36,Extension Channel LL, Short GI, Short Preamble, Single User Beamforming, Radio Scheduling, 30TX Power-30dBm ,TX Antenna Chains-1, RX Antenna Chains-1, Enable-WPA2/WPA3 Personal-CCMP-128 (AES), Regulatory Domain Romania, all-ok
Wireless Interface 2.4GHz-Wireless Mode AP-Wireless Network Mode-N, Width VHT 40 Mhz-Wireless Channel-6, Extension Channel Lower,TurboQAM (QAM256) On, Short Preamble, Short GI, Radio Scheduling,TX Power-30dBm ,TX Antenna Chains-1, RX Antenna Chains-1 Enable-WPA2/WPA3 Personal-CCMP-128 (AES) all-ok![/quote] _________________ Internet provider https://en.wikipedia.org/wiki/RCS_%26_RDS 1Gbps
WDR3600 rev.1.5 - DD-Wrt
Linksys WRT1900ACS v.2 DD-Wrt/-OpenWrt
Joined: 12 Dec 2007 Posts: 782 Location: Pittsburgh, PA USA
Posted: Sun Mar 19, 2023 16:15 Post subject:
Router/Version: WRT1900AC v1
File/Kernel: DD-WRT v3.0-r52054 std (03/18/23)
Previous/Reset: DD-WRT v3.0-r51937 std (03/05/23), Full reset and reconfigure.
Mode/Status: Gateway (SFE enabled), Access Point, IPV6 (DHCP6 w/ prefix delegation), Entware, DOT via SmartDNS/DNSMasq, OpenVPN server, Wireguard Server
Issues/Errors:
Last couple of buids, I had issues with Wifi reliability on the 5GHz band, as well as an issue where the IPV6 address would disappear after clicking Apply on any tab. I skipped the last build, but after reading reports on this one in the other forums, I decided to try it. Seems to be working well.
Up 18 hours, nperf.com shows expected ISP speeds, both wired and wireless. OpenVPN, Wireguard, and DOT, all working as expected.
Joined: 21 Aug 2019 Posts: 120 Location: Here, There And Everywhere
Posted: Sun Mar 19, 2023 20:35 Post subject:
Router/Version: Linksys WRT1200AC / v1
File/Kernel: DD-WRT v3.0-r52054 std (03/18/23) / Linux 4.9.337 #3695 SMP Sat Mar 18 04:32:26 +07 2023 armv7l
Previous/Reset: r52020 / No
Mode/Status: WAP, USB / Working
Issues/Errors:
None so far. Working well as a humble wired AP. With respect to discussion with @blkt regarding switching partitions (r52020 build thread), I can confirm that Web update indeed switches partitions. Thanks again @blkt, one less thing to think about. So switching partitions by hand is only relevant for CLI updates.
Before update:
ubootenv get boot_part
a_pEnv->crc = 34af32b5
crc32 = 34af32b5
1
After update:
ubootenv get boot_part
a_pEnv->crc = dacfcd0c
crc32 = dacfcd0c
2
No need, CLI Flash method 'write' command to 'linux' also automatically flashes to the alternate inactive partition.
'cd /tmp' then 'wget {file URL}' (httponly) or 'curl -O {file URL}' (http, https, ftp). 'write {file} linux' then 'reboot'.
Switch boot_part before a CLI flash, or webUI firmware upgrade, is only a trick to overwrite same active partition.
Since 51937 I am experiencing wifi disconnects multiple times every hour.
Reboot does not help. Reverting back to 51937 does.
No factory reset after update.
EDIT: I've tried with full factory reset and manual setup afterwords. Same behaviour. WiFi disconnects several times in an hour on all connected devices.
Last edited by deshark on Tue Mar 21, 2023 9:25; edited 2 times in total
Since 51937 I am experiencing wifi disconnects multiple times every hour.
Reboot does not help. Reverting back to 51937 does.
1900ACv1 upgraded from 51937 to 52054, no reset
I had upgraded from 51937 to 52054. I just reverted back to see if there is a difference.
I had a few dropouts on a windows laptop, an iPad, and my Steam Deck. Toggling the WiFi connection on the device restored the connection. Waiting to see if I have the same issue on 51937.
Last edited by Rickers on Tue Mar 21, 2023 19:16; edited 1 time in total
Similar issue on my 3200ACM. My iphone and macbook were both connected to the 5ghz radio on the 3200 about 3 feet away. Both disconnected at the same time. Macbook couldn't ping the router and the iphone was just hung up. Reset wifi on macbook and both devices reconnected. No messages in the logs other than the devices reconnecting to wifi. I dropped back down to 51729 (2/16/23).
Router Model & Version: Linksys 3200ACM
Firmware: 52054 (03/18/23)
Previous: 51729 (02/16/23)
Reset: No
Mode: AP / Gateway (3200ACM), Router
Uptime: ran 52054 a couple hours
Status: Performance was good when the wifi connection was working
Issues/Errors: Dropped back to 51729
Environment: 5gh radio: AC/N mixed, Wide HT40, channel 44U, beacon 100, dtim 2.
Antenna Gain lowers output, so leave defaults or zero. TurboQAM is a mixed bag, if you are having issues disable.
What is the correct settings on wrt1900acs v2 usage for the TX Antenna Chains ,RX Antenna Chains:1,1+2,1+3 and maybe someone can explain the way of work to me.
Posted: Thu Mar 23, 2023 14:38 Post subject: Wifi issues on this build
Router Model Linksys WRT1900ACS v2
Wireguard ++
Haven't updated for a while. Just wanted to add to Rickers and pbphoto's experience - that I have the same issue on the WRT1900ACS v2 too.
Intermittent wifi traffic stop on a Samsung S21 Ultra, and some Apple devices. The phone is configured with static lease. The phone reports to be connected - but there is no signal through to the network. Restarting WIFI on the phone brings it back for a while.
