Posted: Tue Mar 21, 2023 10:45 Post subject: New Build - 03/21/2023 - r52081
Welcome to Atheros r52081 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
List router model & version or revision, operating & wireless modes & exact filename/firmware image flashed.
CLI Flash: 'cd /tmp' then 'wget {file URL}' (httponly) or 'curl -O {file URL}' (http, https, ftp). 'write {file} linux' then 'reboot'.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Joined: 12 Dec 2007 Posts: 648 Location: Pittsburgh, PA USA
Posted: Tue Mar 21, 2023 16:00 Post subject:
ho1Aetoo wrote:
Yes the TX power is broken again........
I see the same on two Netgear R7800s being used as wired access points. Reverted to 52054 and signal went back to full strength, no config changes. _________________ __________________________
Linksys WRT-1900AC
DD-WRT v3.0 STD
Netgear R7800
DD-WRT v3.0 STD
Joined: 03 Jan 2010 Posts: 7554 Location: YWG, Canada
Posted: Tue Mar 21, 2023 18:25 Post subject:
vht160 still broken on qca9984 both vanilla and ddwrt radio fw
edit: noticed country code (802.11d) wasnt broadcasting since who knows how long.. but found no_country_ie=0 brings it back, whatever thats all about.. _________________ LATEST FIRMWARE(S)
BrainSlayer wrote:
we just do it since we do not like any restrictions enforced by stupid cocaine snorting managers
Router/Version: Netgear R7800
File: dd-wrt-webupgrade.bin
Firmware: DD-WRT v3.0-r52081 std (03/21/23)
Kernel: Linux 4.9.337 #1701 SMP Tue Mar 21 06:30:56 +07 2023 armv7l
Mode: Gateway, SFE disabled, 2.4G and 5G wifi (FW: DD-WRT), Wireguard for external access, WAN to 4G (DHCP Client), Keep Alive reboot 6:02 in the morning
Reset: No
Status: Installed yesterday, OK.
No problem with 2.4 or 5 GHz at all.
WiFi Analyzer reports round about -30 dBm @ 2.4 (Ch. 11, 20 MHz) & 5 GHz (Ch. 100 UU, 80 MHz) in 3 meter range, Firmware "DD-WRT".
As I have already written several times, the TX power setting is also defective in the dd-wrt firmware.
The dd-wrt Radio Firmware always sends with the full power and the power is not adjustable.
update: CLI r52054 > r52081
reset: NO
mode: Gateway
status: Operational 12h+
errors: Nothing new, yet...apart of the other members WiFi issues, nothing else i could find...
On reboot router comes with very poor range and wifi speeds, log in to the web GUI click save & apply on WiFi section restores the signal range and speeds...so, it works ok but with a gimmick... _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 52459 WAP
TP-Link WR1043NDv2 -DD-WRT 52720 Gateway/DoT,Forced DNS,AP Isolation,Ad-Block,Firewall,VPN,x1VLAN
TP-Link WR1043NDv2 -DD-WRT 52459 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN(no-wifi)
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear R7800 --DD-WRT 52869 Gateway/DoT,AD-Block,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 52459 Gateway/Stubby DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 ---DD-WRT 52869 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby for DNS over TLS I DNSCrypt v2 by mac913
R9000
Services - SMB, Inadyn, Dnscrypt, QOS, DNS Capture, DHCP, Vanilla 2.4 40Mhz, 5.0 Ghz 80 WDS ap on Channel 149 Uu
Errors: none
R7800
Services: WDS STa - 5ghz Channel 149 UU, 2.4GHz AP, 5ghz VAP
Errors - Channel Specific, VAP doesn't function correctly on all channels if int is in wds STA mode (example works fine channel 100, doesn't work at all on 149) ticket #7661
Otherwise other issues already fixed in upcoming release.
Joined: 16 Mar 2019 Posts: 351 Location: Szczecin, Poland EU
Posted: Wed Mar 22, 2023 14:50 Post subject:
On Tp-Link TL-WDR3600 v 1.5 TX Power parameter on system information page is marked as 15 dbm. On wireless settings page I have configured 20. That's incorrect and I don't know how to work my radio module, but I see weak WIFI available area. I wonder this feature working good. Please check this option.
[quote="ho1Aetoo"]I pinged BS and he replied to you in the ticket.
So far he can't reproduce the problem.[/quote]
Uploaded per requests, files show there is an issue with assigned channel. Thetest case he replied with is not the same channel i need to use, and the result is different
