Posted: Mon Mar 13, 2023 8:13 Post subject: New Build - 03/13/2023 - r52004
Welcome to Broadcom r52004 beta release thread for reporting, feedback to developers & community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
List router model & version or revision, operating & wireless modes & exact filename/firmware image flashed.
CLI Flash: 'cd /tmp' then 'wget {file URL}' (httponly) or 'curl -O {file URL}' (http, https, ftp). 'write {file} linux' then 'reboot'.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Linksys E2500
DD-WRT v3.0-r52004 mega (03/13/23)
Linux 4.4.302-st37 #22352 Mon Mar 13 08:03:02 +06 2023 mips
GUI install over r51937
'dd-wrt.v24-52004_NEWD-2_K3.x_mega.bin'
used as a WAP -- all ok
Joined: 18 Mar 2014 Posts: 12915 Location: Netherlands
Posted: Mon Mar 13, 2023 14:40 Post subject:
Router Model: Linksys EA6900 (XVortex CFE)
Firmware Version: DD-WRT v3.0-r52004M Community Build (03/13/23)
Kernel Version: Linux 4.4.302-st37 #1 SMP Mon Mar 13 08:13:59 CET 2023 armv7l
Upgraded from DD-WRT v3.0-r51935M Community Build (03/04/23) via telnet (update via GUI not possible because nvram is placed on linux partition and not linux2 partition due to Xvortex CFE)
Reset: No not this time.
Configuration: Default gateway mode, 2,4GHz wireless running with unbridged VAP, 5GHz running, some static leases and some port range forwarding.
WireGuard client running with PBR.
OpenVPN client with PBR running, OpenVPN server tested and working
IPv6 working.
NAS and ksmbd working.
NVRAM size 47K (NVRAM size should not be a problem with the Xvortex CFE)
Router/Version: Asus RT-N18U
Firmware: DD-WRT v3.0-r52004 std (03/13/23)
Kernel: Linux 4.4.302-st37 #8901 Mon Mar 13 06:51:34 +06 2023 armv7l
Mode: gateway
Previous: r51887
Reset: no
Status: I cannot see switch config until I enable Vlans radio button under Switch Config tab.
In previous builds it was always visible so I could check active ports - not sure if this is expected behaviour?
It is expected behavior. _________________ "The woods are lovely, dark and deep,
But I have promises to keep,
And miles to go before I sleep,
And miles to go before I sleep." - Robert Frost
"I am one of the noticeable ones - notice me" - Dale Frances McKenzie Bozzio
On some routers, enabling the switch config tab overwrites the port configuration factory setting.
And it was impossible to restore the factory settings without factory reset or backup.
Now you can simply disable the "VLAN configuration", which restores the default configuration.
This may also be useful if you have changed a lot of settings and do not know what the default configuration was.