Router/Version: Netgear R7800
File: dd-wrt-webupgrade.bin
Firmware: DD-WRT v3.0-r51506 std (01/25/23)
Kernel: Linux 4.9.337 #1501 SMP Wed Jan 25 01:56:15 +07 2023 armv7l
Mode: Gateway, SFE disabled, 2.4G and 5G wifi, Wireguard for external access, WAN to 4G (DHCP Client), Keep Alive reboot 6:02 in the morning
Reset: No
Status: Installed yesterday, OK.
Regarding mentioned LEDs... I cannot issue any information, since I used electrical tape to stop those LEDs illuminating the room when it is getting dark.
Joined: 16 Nov 2015 Posts: 6446 Location: UK, London, just across the river..
Posted: Thu Jan 26, 2023 11:25 Post subject:
Zyxx wrote:
Router/Version: Netgear R7800
File: dd-wrt-webupgrade.bin
Firmware: DD-WRT v3.0-r51506 std (01/25/23)
Kernel: Linux 4.9.337 #1501 SMP Wed Jan 25 01:56:15 +07 2023 armv7l
Mode: Gateway, SFE disabled, 2.4G and 5G wifi, Wireguard for external access, WAN to 4G (DHCP Client), Keep Alive reboot 6:02 in the morning
Reset: No
Status: Installed yesterday, OK.
Regarding mentioned LEDs... I cannot issue any information, since I used electrical tape to stop those LEDs illuminating the room when it is getting dark.
hmmm...scotch tape...on R7800..?? bloody R7800 has an on/off switch on the back ...unless yours is broken...tape does well...the other solution i use on my R7000 witch doesn't have a switch is start up script and a bit of permanent black marker
to be honest ive never been interested on router lights and some people around are craving for those... _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55630 WAP
TP-Link WR1043NDv2 -DD-WRT 55723 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55779 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55819 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55779 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
R7800
No reset
WDS STA on 5ghz AC/N, Vanilla FW, 5GHz VAp. 2GHz Mixed N/AC
The 5Ghz LED seems to be out for last few firmware builds, anyone else experiencing this? Functionally all traffic over the interface is fine, its just the LED.
I noticed this on r51275, cleared nvram a few times to no avail, yet I noticed on the odd occasion the r7800 will boot up with the 5.0G light functioning correctly. Not reported as no big deal, BS has never seem to been interested in LED's. _________________ Netgear R7800 PPPoE Main Router
Network IPV4 - Isolated Vlan's with IoT Devices. Unifi AC-Pro x 3 AP's, Router Wi-Fi Disabled. OVPN Server With Paid Commercial Wireguard Client's. Gateway Mode, DNSMasq, Static Leases & DHCP, Pi-Hole DNS & Running Unbound.
No one can build you the bridge on which you, and only you, must cross the river of life!
Check dmesg boot log to see if vanilla firmware is crashing after the switchover from dd-wrt to vanilla firmware type.
If this is true try r50927 and see if precious blinkies are blinking. EA8500 I'm using r50927 for performance reasons.
On r50927 R7800 my precious blinkies are blinking BLKT sorry not checked logs, its on my spare r7800 so I just flashed back, no reset from r51275, rebooted 3 times 5.0G light seems to function on this FW version correctly mate. Only tested it so it may help fix the issue. _________________ Netgear R7800 PPPoE Main Router
Network IPV4 - Isolated Vlan's with IoT Devices. Unifi AC-Pro x 3 AP's, Router Wi-Fi Disabled. OVPN Server With Paid Commercial Wireguard Client's. Gateway Mode, DNSMasq, Static Leases & DHCP, Pi-Hole DNS & Running Unbound.
No one can build you the bridge on which you, and only you, must cross the river of life!
R7800
No reset
WDS STA on 5ghz AC/N, Vanilla FW, 5GHz VAp. 2GHz Mixed N/AC
The 5Ghz LED seems to be out for last few firmware builds, anyone else experiencing this? Functionally all traffic over the interface is fine, its just the LED.
Do a Hard Reboot until it starts flashing again if it's important. Use to drive my OCD a little over the edge and I would just turn off the LEDs on my XR500.
I to was able to get the 5Ghz Radio LED on the R7800 flashing after a couple of Resets but during the the manual configuration and reboots the 5Ghz Radio LED would go into a state of staying OFF. It doesn't effect my clients connecting but looks like the 5Ghz Radio is OFF when it is not. _________________ Home Network on Telus 1Gb PureFibre - 10GbE Copper Backbone
2x R7800 - Gateway & WiFi & 3xWireGuard - DDWRT r53562 Std k4.9
Off Site 1
R7000 - Gateway & WiFi & WireGuard - DDWRT r54517 Std
E3000 - Station Bridge - DDWRT r49626 Mega K4.4
Off Site 2
R7000 - Gateway & WiFi - DDWRT r54517 Std
E2000 - Wired ISP IPTV PVR Blocker - DDWRT r35531
@alozaros
The power LED wasn't affected if I remember right.
And since gpio disable 0 just stops working at midnight and sometimes randomly during the day / night --> tape was the best solution.
Joined: 05 Oct 2008 Posts: 666 Location: Helsinki, Finland / nr. Alkmaar, Netherlands
Posted: Sat Jan 28, 2023 20:27 Post subject:
R7800 on build 51506
No matter how often I reboot the router, select different 5 GHz firmware, apply settings, I can't make the 5 GHz LED blink again.
On previous builds changing the WiFi firmware back and forth and applying settings and/or rebooting used to get the 5 GHz LED working again, but not anymore.
And, well, yes, the dead LED is annoying, although it doesn't apparently affect the 5 GHz WiFi in the least.
The 2.4 GHz LED OTOH has been working fine all the time.
Joined: 21 Aug 2019 Posts: 120 Location: Here, There And Everywhere
Posted: Sat Jan 28, 2023 23:49 Post subject:
Router/Version: TP-Link ARCHER-C7 v5
File/Kernel: DD-WRT v3.0-r51506 std (01/25/23) / Linux 3.18.140-d6 #161850 Wed Jan 25 06:31:24 +06 2023 mips
Previous/Reset: r51440/No reset
Mode/Status: WDS AP / OK
Issues/Errors: None so far.
Web upgrade. Running for two days with no problems.
Joined: 16 Mar 2019 Posts: 353 Location: Szczecin, Poland EU
Posted: Sun Jan 29, 2023 12:37 Post subject: New Build - 01/25/2023 - r51506
Router: Tp-Link TL-WDR3600 v 1.5
Kernel: Linux 3.10.108-d11 #124486 Wed Jan 25 03:47:27 +06 2023 mips
Reset: No
Mode: internet gateway, WIFI 5GHz AP, dnsmasq server, firewall
Status: Working
Issues: Nothing significant
Uptime: a few days
Router working rather good. I have some yellow marked events in logs, but device is operating.
None of my Google camera devices would connect with this version. Downgraded and everything reconnected. Will do more troubleshooting / get more info later today.
Check that "QCA Q-Boost / TDMA" is disabled. For some reason I had this enabled, and with a few of the latest builds my Samsung tablet was constantly disconnecting. I thought it was the tablet until some extensive googling finally led me to the solution.
@routemegood "None of my Google camera devices would connect with this version. Downgraded and everything reconnected. Will do more troubleshooting / get more info later today."
If you disable turboQAM on 2.4GHz, do your cameras connect?
That did not fix. It appears to cause issues with other devices as well. Devices connect but very slowly and seemed to get dropped. Not sure what the deal is. Will have to dig more. I have reverted to the 1/16 build. That one is stable.
None of my Google camera devices would connect with this version. Downgraded and everything reconnected. Will do more troubleshooting / get more info later today.
Check that "QCA Q-Boost / TDMA" is disabled. For some reason I had this enabled, and with a few of the latest builds my Samsung tablet was constantly disconnecting. I thought it was the tablet until some extensive googling finally led me to the solution.