Posted: Wed Jan 25, 2023 9:22 Post subject: New Build - 01/25/2023 - r51506
Welcome to Broadcom r51506 beta release thread for reporting, feedback to developers & community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Joined: 18 Mar 2014 Posts: 12855 Location: Netherlands
Posted: Wed Jan 25, 2023 9:59 Post subject:
Router Model: Netgear R6400v1
Firmware Version: DD-WRT v3.0-r51506M Community Build (01/25/23)
Kernel Version: Linux 4.4.302-st28 #1 SMP Wed Jan 25 08:24:05 CET 2023 armv7l
Upgraded from: DD-WRT v3.0-r50967M Community Build (11/28/22)
Reset: No not this time
Status: Up and running for 2 hours, basic setup as Gateway, static leases, Advanced routing, Port Forwarding, IPv4, 2.4 GHz with unbridged VAP and 5 GHz.
Running one WireGuard tunnel to Mullvad with IPv6 (experimental) and second WireGuard tunnel to own WG server for site-to-site connection also with IPv6.
OpenVPN client tested and working.
Linksys E2500
DD-WRT v3.0-r51506 mega (01/25/23)
Linux 4.4.302-st28 #21124 Wed Jan 25 03:56:16 +06 2023 mips
'dd-wrt.v24-51506_NEWD-2_K3.x_mega.bin'
GUI install over r51440
just a WAP
all is good
Joined: 18 Mar 2014 Posts: 12855 Location: Netherlands
Posted: Wed Jan 25, 2023 11:57 Post subject:
Router Model: Netgear R6400v2, board_id: U12H332T
Firmware Version: DD-WRT v3.0-r51506M Community Build (01/25/23)
Kernel Version: Linux 4.4.302-st28 #1 SMP Wed Jan 25 08:24:05 CET 2023 armv7l
Upgraded from: DD-WRT v3.0-r51440M Community Build (01/19/23)
Reset: No not this time
Status: Up and running for 4 hours, basic setup as Gateway, static leases, 2,4GHz and 5Ghz working, USB storage NAS working. IPv6 working. SmartDNS working with DoT.
OpenVPN server working.
WireGuard server working with 8 clients (phones, Windows and two other routers for site-to-site setup) also supports IPV6 clients.
mDNS/Avahi working.
Posted: Wed Jan 25, 2023 19:55 Post subject: ASUS RT-AC68U & 2 x Linksys E2000
Asus RT-AC68U
Firmware: DD-WRT v3.0-r51506 std (01/25/23) - (previous R51440)
Kernel: Linux 4.4.302-st28 #8560 SMP Wed Jan 25 02:05:11 +06 2023 armv7l
5Ghz (Mixed) with 80Mhz channel width (upper/lower): Ok
SSH: Ok
Telnet: Disabled
Site Survey: Ok
Wi-viz Survey 2.4Ghz & 5Ghz: Ok
Reset: No
Status: Ok
Uptime: 3:54
CPU Temperature: CPU 68.0 °C / WL0 46.5 °C / WL1 44.5 °C
2 x E2000
Firmware: DD-WRT v3.0-r51506 mega (01/25/23) - (previous r51440)
Kernel: Linux 4.4.302-st28 #21124 Wed Jan 25 03:56:16 +06 2023 mips
2.4Ghz (NG-mixed) with 40Mhz channel width: Ok
SSH: Ok
Telnet: Disabled
Site Survey: Ok
Wi-viz Survey 2.4Ghz: Ok
Reset: No
Status: Ok
Uptime: 4:01
CPU Temperature: WL0 49.0 °C/WL0 50.7 °C
All devices working as AP's each with individual 1Gb wired connections to main firewalls
No issues so far, will update if experiencing any.
Posted: Thu Jan 26, 2023 0:26 Post subject: Netgear Nighthawk R7000
Router/Version: Netgear R7000 Firmware: DD-WRT v3.0-r51506 std (01/25/23) Kernel: Linux 4.4.302-st28 #8560 SMP Wed Jan 25 02:05:11 +06 2023 armv7l Mode: Gateway, Wireless AP, Static Leases, Dnsmasq Caching. CTF & FA Enabled. NAT and QOS Off. All services off under Status>Sys-info. Reset: Nope, ran remove unused NVRAM parameters script. Previous: 01-19-2023-r51440 Status: Working so far, still testing. wl: 14E4:4360 Overclocked: 1200,1600 Temperatures: CPU 52.5 °C / WL0 47.9 °C / WL1 49.4 °C Base CFE: Modified Asus ASUS RT-AC68P/ASUS RT-AC68U (C0 Model CFE V1.3.0.7) Configured as a stock R7000.
Speedtest-2.jpg
Description:
Speedtest Over 5.8GHz Wireless. ISP Spec: 500 Mbps Down / 25 Mbps Up.
Router/Version: Asus RT-N66U
File: dd-wrt.v24-51506_NEWD-2_K3.x-big-RT-N66U.trx
Firmware: DD-WRT v3.0-r51506 big (01/25/23)
Kernel: Linux 4.4.302-st28 #21120 Wed Jan 25 03:51:02 +06 2023 mips
Mode: Gateway, SFE disabled, Wifi disabled, WAN disabled, Wireguard Endpoint for external VPS, connected via LAN to WRT1900ACS v2, Keep Alive reboot 6:05 in the morning
Reset: No
Status: Installed yesterday, OK.
Router/Version: Linksys EA6350 v2
File/Kernel: DD-WRT v3.0-r51506 std (01/25/23)
Previous/Reset: r46316, flashed from scratch before upgrading to this new rev via web upload
Mode/Status: Station/Client
Issues/Errors: None so far, looking good. Had an issue previously where UPnP would turn off after reboot, time will tell if it'll come back. Not in a position to reboot it any further at this time. Re-flash came after the router bonked out out of the blue. Inspection in CFE showed that the router decided it was tired of the same old MAC addresses for all its inferfaces, and moved them all up one bit. Some took over the MAC addresses of other interfaces and the one at the end of the queue got a brand new one, lucky duck. Not so lucky for the setup, of course. Setup has been running solid for over a year on the previous revision (r46316), except for the UPnP issue. _________________ Routers:
Linksys EA6350v2 - dd-wrt r51506 (Client/Station mode), how-to flash
Ubiquiti UniFi U6 LR - Stock (active AP)
TP-Link Archer C2 v1 - OpenWRT (gathering dust)