procsacs DD-WRT Novice
Joined: 27 Jan 2023 Posts: 2
|
Posted: Fri Jan 27, 2023 21:41 Post subject: ASUS RT-AC87U stuck on broken dd wrt |
|
Hi All
I got a broken router ASUS RT-AC87U, after turning it on, sometimes a lan or wifi connection worked, (open network "dd-wrt"), but it did not assign an IP address, no connection to the GUI (even with a static ip), I tried to upload the original asus firmware (RT- AC87U_3.0.0.4_382_52545-ga0245cc.trx) using asus rescue (Firmware Restoration), the router started in recovery mode, but there was not always a LAN connection, as if ports were disabled, several times it was possible to connect, but with different % an error popped up and it won't load the firmware. How to restore this router ?
After connecting serial TTL, you can see how DD-WRT starts, here are the logs:
Error upload firmware :
break! no netctx or timer expired !
break!! reach max retry!!
Failed.: I/O error
*** command status = -4
And i try flash by this:
flash -noheader : nflash1.trx
that same result
and i use: nvram erase
boot :
Code: | Decompressing...done
Digital core power voltage set to 1.0V
SHMOO VER 1.13
PKID07DC06011801080000000000001A103F01000000
Decompressing...done
Detect CPU turbo button...
CFE version 6.37.14.86 (r456083) based on BBP 1.0.37 for BCM947XX (32bit,SP,)
Build Date: 二 4月 22 16:05:16 CST 2014 (raymonddev@raymonddev-vm1210)
Copyright (C) 2000-2008 Broadcom Corporation.
Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
DDR Clock: 800 MHz
Info: DDR frequency set from clkfreq=1000,*800*
et1: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.37.14.86 (r456083)
CPU type 0x0: 1000MHz
Tot mem: 262144 KBytes
CFE mem: 0x00F00000 - 0x01795558 (9000280)
Data: 0x00F4DBB4 - 0x00F4E080 (1228)
BSS: 0x00F4E090 - 0x00F93558 (283848)
Heap: 0x00F93558 - 0x01793558 (8388608)
Stack: 0x01793558 - 0x01795558 (8192)
Text: 0x00F00000 - 0x00F4430C (279308)
Device eth0: hwaddr 88-D7-F6-44-22-E0, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
Null Rescue Flag.
boot the image...
go load
Loader:raw Filesys:tftp Dev:eth0 File:: Options:(null)
Loading: TFTP Server.
..tftp retry wait 0
..tftp retry wait 1
..tftp retry wait 2
..tftp retry wait 3
..tftp retry wait 4
Failed.
Could not load :: Timeout occured
Loader:raw Filesys:raw Dev:nflash0.os File: Options:(null)
Loading: ... 1720360 bytes read
Entry at 0x00008000
Closing network.
Starting program at 0x00008000
Uncompressing Linux... done, booting the kernel.
Booting Linux on physical CPU 0x0
Linux version 4.4.241 (root@linux) (gcc version 10.0.1 (OpenWrt GCC 10.0.1 r12423-0493d57e04) ) #1330 SMP Tue Nov 3 09:24:03 +03 2020
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: Northstar Prototype
Ignoring unrecognised tag 0x00000000
Memory policy: Data cache writealloc
map io
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0x88800000 - 0xff800000 (1904 MB)
lowmem : 0x80000000 - 0x88000000 ( 128 MB)
pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
modules : 0x7f000000 - 0x7fe00000 ( 14 MB)
.text : 0x80008000 - 0x804dc81c (4947 kB)
.init : 0x804dd000 - 0x80534000 ( 348 kB)
.data : 0x80534000 - 0x805667f4 ( 202 kB)
.bss : 0x80569000 - 0x805c3f4c ( 364 kB)
Hierarchical RCU implementation.
CONFIG_RCU_FANOUT set to non-default value of 2
Build-time adjustment of leaf fanout to 2.
NR_IRQS:256
MPCORE GIC init
soc_dmu_init
add clk lookups
MPCORE Global Timer Clock 500000000Hz on IRQ 27
sched_clock: 32 bits at 500MHz, resolution 2ns, wraps every 4294967295ns
clocksource: mpcore_gtimer: mask: 0xffffffffffffffff max_cycles: 0xe6a171a037, max_idle_ns: 881590485102 ns
register local timer
smp_twd: clock not found -2
Calibrating local timer... 499.73MHz.
Calibrating delay loop... 1987.37 BogoMIPS (lpj=9936896)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
2 cores has been found
Found a AMD NAND flash:
Total size: 128MB
Block size: 128KB
Page Size: 2048B
OOB Size: 64B
Sector size: 512B
Spare size: 16B
ECC level: 8 (8-bit)
Device ID: 0x 1 0xf1 0x80 0x1d 0x 1 0xf1
found nand nvram at 80000
DD-WRT v3.0-r44715 std (c) 2020 NewMedia-NET GmbH
Release: 11/03/20
Board: Asus RT-AC87U
DD-WRT login: root
Password:
==========================================================
___ ___ _ _____ ______ ____ ___
/ _ \/ _ \___| | /| / / _ \/_ __/ _ __|_ / / _ \
/ // / // /___/ |/ |/ / , _/ / / | |/ //_ <_/ // /
/____/____/ |__/|__/_/|_| /_/ |___/____(_)___/
DD-WRT v3.0
http://www.dd-wrt.com
==========================================================
login[1378]: root login on 'console'
BusyBox v1.32.0 (2020-11-03 09:25:05 +03) built-in shell (ash)
root@DD-WRT:~#
root@DD-WRT:~# ifconfig
br0 Link encap:Ethernet HWaddr 88:D7:F6:44:22:E2
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:236 errors:0 dropped:0 overruns:0 frame:0
TX packets:201 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:19532 (19.0 KiB) TX bytes:8442 (8.2 KiB)
br0:1 Link encap:Ethernet HWaddr 88:D7:F6:44:22:E2
inet addr:169.254.39.215 Bcast:169.254.39.255 Mask:255.255.255.0
UP BROADCAST MULTICAST MTU:1500 Metric:1
br0:2 Link encap:Ethernet HWaddr 88:D7:F6:44:22:E2
inet addr:1.1.1.1 Bcast:1.1.1.255 Mask:255.255.255.0
UP BROADCAST MULTICAST MTU:1500 Metric:1
eth0 Link encap:Ethernet HWaddr 88:D7:F6:44:22:E0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:5070 errors:0 dropped:0 overruns:0 frame:0
TX packets:1706 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:788608 (770.1 KiB) TX bytes:82076 (80.1 KiB)
Interrupt:180 Base address:0x5000
eth1 Link encap:Ethernet HWaddr 88:D7:F6:44:22:E2
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:6400
TX packets:338 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:29788 (29.0 KiB)
Interrupt:163
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MULTICAST MTU:65536 Metric:1
RX packets:6841 errors:0 dropped:0 overruns:0 frame:0
TX packets:6841 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1
RX bytes:3897764 (3.7 MiB) TX bytes:3897764 (3.7 MiB)
vlan1 Link encap:Ethernet HWaddr 88:D7:F6:44:22:E0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:5070 errors:0 dropped:0 overruns:0 frame:0
TX packets:1694 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:677068 (661.1 KiB) TX bytes:71148 (69.4 KiB)
root@DD-WRT:~#
|
Process:
Code: | root@DD-WRT:~# ps
PID USER COMMAND
1 root /sbin/init
2 root [kthreadd]
3 root [ksoftirqd/0]
4 root [kworker/0:0]
5 root [kworker/0:0H]
7 root [rcu_sched]
8 root [rcu_bh]
9 root [migration/0]
10 root [migration/1]
11 root [ksoftirqd/1]
12 root [kworker/1:0]
13 root [kworker/1:0H]
14 root [kworker/u4:1]
117 root [kworker/u4:2]
127 root [writeback]
129 root [crypto]
130 root [bioset]
132 root [kblockd]
136 root [kworker/u5:0]
160 root [kworker/1:1]
202 root [kswapd0]
203 root [vmstat]
204 root [fsnotify_mark]
226 root [kworker/0:1]
233 root [bioset]
234 root [bioset]
235 root [bioset]
236 root [bioset]
237 root [bioset]
238 root [bioset]
239 root [bioset]
240 root [bioset]
241 root [bioset]
242 root [bioset]
243 root [bioset]
244 root [bioset]
245 root [bioset]
246 root [bioset]
247 root [bioset]
248 root [bioset]
282 root [bioset]
285 root [bioset]
288 root [bioset]
291 root [bioset]
294 root [bioset]
297 root [bioset]
300 root [bioset]
303 root [bioset]
311 root [bioset]
316 root [bioset]
321 root [bioset]
326 root [bioset]
343 root [deferwq]
346 root [bioset]
350 root [kworker/0:1H]
351 root [kworker/1:1H]
606 root /sbin/hotplug2 --set-rules-file /etc/hotplug2.rules --persistent
610 root /sbin/mstpd
614 root irqbalance -t 10
741 root tftpd
975 root httpd -n -p 80
1377 root /bin/login
1378 root -sh
1704 root ps
root@DD-WRT:~# top
Mem: 46540K used, 207748K free, 0K shrd, 9284K buff, 21160K cached
CPU: 0.0% usr 0.0% sys 0.0% nic 100% idle 0.0% io 0.0% irq 0.0% sirq
Load average: 1.01 1.00 0.81 1/65 1716
PID PPID USER STAT VSZ %VSZ CPU %CPU COMMAND
1716 1378 root R 1440 0.5 0 0.0 top
975 1 root S 4052 1.5 1 0.0 httpd -n -p 80
1378 1377 root S 1440 0.5 0 0.0 -sh
1377 1 root S 1440 0.5 1 0.0 /bin/login
1 0 root S 1024 0.4 0 0.0 /sbin/init
614 1 root S 992 0.3 0 0.0 irqbalance -t 10
610 1 root S 824 0.3 1 0.0 /sbin/mstpd
606 1 root S 776 0.3 1 0.0 /sbin/hotplug2 --set-rules-file /e
741 1 root S 748 0.2 1 0.0 tftpd
226 2 root SW 0 0.0 0 0.0 [kworker/0:1]
160 2 root SW 0 0.0 1 0.0 [kworker/1:1]
7 2 root SW 0 0.0 0 0.0 [rcu_sched]
3 2 root SW 0 0.0 0 0.0 [ksoftirqd/0]
11 2 root SW 0 0.0 1 0.0 [ksoftirqd/1]
9 2 root SW 0 0.0 0 0.0 [migration/0]
10 2 root SW 0 0.0 1 0.0 [migration/1]
14 2 root SW 0 0.0 1 0.0 [kworker/u4:1]
130 2 root SW< 0 0.0 0 0.0 [bioset]
136 2 root SW< 0 0.0 0 0.0 [kworker/u5:0]
129 2 root SW< 0 0.0 0 0.0 [crypto]
|
Code: |
Decompressing...done
Digital core power voltage set to 1.0V
SHMOO VER 1.13
Decompressing...done
Detect CPU turbo button...
CFE version 6.37.14.86 (r456083) based on BBP 1.0.37 for BCM947XX (32bit,SP,)
Build Date: 二 4月 22 16:05:16 CST 2014 (raymonddev@raymonddev-vm1210)
Copyright (C) 2000-2008 Broadcom Corporation.
Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
DDR Clock: 800 MHz
Info: DDR frequency set from clkfreq=1000,*800*
et1: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.37.14.86 (r456083)
CPU type 0x0: 1000MHz
Tot mem: 262144 KBytes
CFE mem: 0x00F00000 - 0x01795558 (9000280)
Data: 0x00F4DBB4 - 0x00F4E080 (1228)
BSS: 0x00F4E090 - 0x00F93558 (283848)
Heap: 0x00F93558 - 0x01793558 (8388608)
Stack: 0x01793558 - 0x01795558 (8192)
Text: 0x00F00000 - 0x00F4430C (279308)
Device eth0: hwaddr 88-D7-F6-44-22-E0, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
Startup canceled
CFE> nvram erase
*** command status = 0
CFE> show devices
Device Name Description
------------------- ---------------------------------------------------------
uart0 NS16550 UART at 0x18000300
uart1 NS16550 UART at 0x18000400
nflash0 AMD NAND flash size 131072KB
nflash0.boot AMD NAND flash offset 0 size 512KB
nflash0.nvram AMD NAND flash offset 80000 size 1536KB
nflash0.trx AMD NAND flash offset 200000 size 1KB
nflash0.os AMD NAND flash offset 20001C size 129024KB
nflash1.boot AMD NAND flash offset 0 size 512KB
nflash1.nvram AMD NAND flash offset 80000 size 1536KB
nflash1.trx AMD NAND flash offset 200000 size 129024KB
eth0 Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller
*** command status = 0
CFE> ^C
CFE> reboot▒Digital core power voltage set to 1.0V
Decompressing...done
Detect CPU turbo button...
CFE version 6.37.14.86 (r456083) based on BBP 1.0.37 for BCM947XX (32bit,SP,)
Build Date: 二 4月 22 16:05:16 CST 2014 (raymonddev@raymonddev-vm1210)
Copyright (C) 2000-2008 Broadcom Corporation.
Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
DDR Clock: 400 MHz
Info: DDR frequency set from clkfreq=1000,*800*
Warning: invalid DDR setting of 800 MHz ignored. DDR frequency will be set to 400 MHz.
et1: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.37.14.86 (r456083)
CPU type 0x0: 1000MHz
Tot mem: 262144 KBytes
CFE mem: 0x00F00000 - 0x01795558 (9000280)
Data: 0x00F4DBB4 - 0x00F4E080 (1228)
BSS: 0x00F4E090 - 0x00F93558 (283848)
Heap: 0x00F93558 - 0x01793558 (8388608)
Stack: 0x01793558 - 0x01795558 (8192)
Text: 0x00F00000 - 0x00F4430C (279308)
Committing NVRAM...done
Waiting for wps button release...donDigital core power voltage set to 1.0V
Decompressing...done
Detect CPU turbo button...
CFE version 6.37.14.86 (r456083) based on BBP 1.0.37 for BCM947XX (32bit,SP,)
Build Date: 二 4月 22 16:05:16 CST 2014 (raymonddev@raymonddev-vm1210)
Copyright (C) 2000-2008 Broadcom Corporation.
Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
DDR Clock: 800 MHz
Info: DDR frequency set from clkfreq=1000,*800*
et1: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.37.14.86 (r456083)
CPU type 0x0: 1000MHz
Tot mem: 262144 KBytes
CFE mem: 0x00F00000 - 0x01795558 (9000280)
Data: 0x00F4DBB4 - 0x00F4E080 (1228)
BSS: 0x00F4E090 - 0x00F93558 (283848)
Heap: 0x00F93558 - 0x01793558 (8388608)
Stack: 0x01793558 - 0x01795558 (8192)
Text: 0x00F00000 - 0x00F4430C (279308)
Device eth0: hwaddr 88-D7-F6-44-22-E0, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
Null Rescue Flag.
boot the image...
go load
Loader:raw Filesys:tftp Dev:eth0 File:: Options:(null)
Loading: TFTP Server.
..tftp retry wait 0
Failed.
Could not load :: Timeout occured
Loader:raw Filesys:raw Dev:nflash0.os File: Options:(null)
Loading: ... 1720360 bytes read
Entry at 0x00008000
Closing network.
Starting program at 0x00008000
Uncompressing Linux... done, booting the kernel.
Booting Linux on physical CPU 0x0
Linux version 4.4.241 (root@linux) (gcc version 10.0.1 (OpenWrt GCC 10.0.1 r12423-0493d57e04) ) #1330 SMP Tue Nov 3 09:24:03 +03 2020
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: Northstar Prototype
Ignoring unrecognised tag 0x00000000
Memory policy: Data cache writealloc
map io
MPCORE found at 19020000 (VIRT 99020000) 18000000 98000000
Hit pending asynchronous external abort (FSR=0x00001c06) during first unmask, this is most likely caused by a firmware/bootloader bug.
PERCPU: Embedded 11 pages/cpu @86dd4000 s13068 r8192 d23796 u45056
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65280
Kernel command line: console=ttyS0,115200 panic=10 root=/dev/mtdblock3 earlyprintk=1 rootfstype=squashfs,jffs2 noinitrd init=/bin/sh
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 253940K/262144K available (3692K kernel code, 201K rwdata, 1252K rodata, 348K init, 363K bss, 8204K reserved, 0K cma-reserved, 131072K highmem)
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0x88800000 - 0xff800000 (1904 MB)
lowmem : 0x80000000 - 0x88000000 ( 128 MB)
pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
modules : 0x7f000000 - 0x7fe00000 ( 14 MB)
.text : 0x80008000 - 0x804dc81c (4947 kB)
.init : 0x804dd000 - 0x80534000 ( 348 kB)
.data : 0x80534000 - 0x805667f4 ( 202 kB)
.bss : 0x80569000 - 0x805c3f4c ( 364 kB)
Hierarchical RCU implementation.
CONFIG_RCU_FANOUT set to non-default value of 2
Build-time adjustment of leaf fanout to 2.
NR_IRQS:256
MPCORE GIC init
soc_dmu_init
add clk lookups
MPCORE Global Timer Clock 500000000Hz on IRQ 27
sched_clock: 32 bits at 500MHz, resolution 2ns, wraps every 4294967295ns
clocksource: mpcore_gtimer: mask: 0xffffffffffffffff max_cycles: 0xe6a171a037, max_idle_ns: 881590485102 ns
register local timer
smp_twd: clock not found -2
Calibrating local timer... 499.71MHz.
Calibrating delay loop... 1987.37 BogoMIPS (lpj=9936896)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, |
Last edited by procsacs on Sat Jan 28, 2023 21:37; edited 1 time in total |
|
procsacs DD-WRT Novice
Joined: 27 Jan 2023 Posts: 2
|
Posted: Fri Jan 27, 2023 23:34 Post subject: |
|
Thank you very much for your answer, tried to upload firmware via rcovery mode several times, but it always fails in windows recovery tool, with different % values (15%,36%,75%), the GIU doesn't work, only the "root@DD-WRT:~#" console transfers the serial TTL, but I don't know how to use it.
how to "command line flash upgrade " ? Use only TTL .
Code: | ..tftp retry wait 0
break! no netctx or timer expired !
break!! reach max retry!!
Failed.: I/O error
Loader:raw Filesys:raw Dev:nflash0.os File: Options:(null)
Loading: ... 1720360 bytes read
Entry at 0x00008000
Closing network.
Starting program at 0x00008000
Uncompressing Linux... done, booting the kernel.
Booting Linux on physical CPU 0x0
Linux version 4.4.241 (root@linux) (gcc version 10.0.1 (OpenWrt GCC 10.0.1 r1242 3-0493d57e04) ) #1330 SMP Tue Nov 3 09:24:03 +03 2020
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d |
Code: | CFE version 6.37.14.86 (r456083) based on BBP 1.0.37 for BCM947XX (32bit,SP,) |
BCM947XX ??
Code: | CFE> show devices
Device Name Description
------------------- ---------------------------------------------------------
uart0 NS16550 UART at 0x18000300
uart1 NS16550 UART at 0x18000400
nflash0 AMD NAND flash size 131072KB
nflash0.boot AMD NAND flash offset 0 size 512KB
nflash0.nvram AMD NAND flash offset 80000 size 1536KB
nflash0.trx AMD NAND flash offset 200000 size 1KB
nflash0.os AMD NAND flash offset 20001C size 129024KB
nflash1.boot AMD NAND flash offset 0 size 512KB
nflash1.nvram AMD NAND flash offset 80000 size 1536KB
nflash1.trx AMD NAND flash offset 200000 size 129024KB
eth0 Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller
-----------------
et1macaddr=88:D7:F6:44:22:E0
CFE> nvram get et0macaddr
*** command status = 0
CFE> nvram get 0:macaddr
88:D7:F6:44:22:E0
*** command status = 0
CFE> nvram get 1:macaddr
88:D7:F6:44:22:E4
|
et1 et0 ?
----------------
UPDATE ! THX
Thank you, successfully installed Asuswrt-Merlin 380.69, but I tried to use another PC, I don't know why on a windows 7 laptop it did not want to upload the firmware, after changing to a win 10 PC, finally it went for the hundredth time.
Code: |
CFE> ifconfig eth0 -auto
Invalid switch: -auto
*** command status = -8
CFE> ifconfig eth0 -auto
Invalid switch: -auto
*** command status = -8
CFE> ifconfig eth1 -addr=192.168.1.1
Network interface has not been configured
*** command status = 0
CFE> help
Available commands:
nvram NVRAM utility.
reboot Reboot.
flash Update a flash memory device
batch Load a batch file into memory and execute it
go Verify and boot OS image.
boot Load an executable file into memory and execute it
load Load an executable file into memory without executing it
save Save a region of memory to a remote file via TFTP
ping Ping a remote IP host.
arp Display or modify the ARP Table
ifconfig Configure the Ethernet interface
show clocks Show current values of the clocks.
show devices Display information about the installed devices.
help Obtain help for CFE commands
For more information about a command, enter 'help command-name'
*** command status = 0
CFE> show devices
Device Name Description
------------------- ---------------------------------------------------------
uart0 NS16550 UART at 0x18000300
uart1 NS16550 UART at 0x18000400
nflash0 AMD NAND flash size 131072KB
nflash0.boot AMD NAND flash offset 0 size 512KB
nflash0.nvram AMD NAND flash offset 80000 size 1536KB
nflash0.trx AMD NAND flash offset 200000 size 1KB
nflash0.os AMD NAND flash offset 20001C size 129024KB
nflash1.boot AMD NAND flash offset 0 size 512KB
nflash1.nvram AMD NAND flash offset 80000 size 1536KB
nflash1.trx AMD NAND flash offset 200000 size 129024KB
eth0 Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller
*** command status = 0
CFE> flash -noheader : nflash1.trx
Reading :: TFTP Server.
Failed.: Error
*** command status = -1
CFE> flash -noheader : nflash1.trx
Reading :: TFTP Server.
Failed.: Error
*** command status = -1
CFE> flash -noheader -forceflash : nflash1.trx
Reading :: TFTP Server.
Failed.: Error
*** command status = -1
CFE> ifconfig eth0 -addr=192.168.1.1 -mask=255.255.255.0 -gw=192.168.1.1
Device eth0: hwaddr 88-D7-F6-44-22-E0, ipaddr 192.168.1.1, mask 255.255.255.0
gateway 192.168.1.1, nameserver not set
*** command status = 0
CFE> flash -noheader -forceflash : nflash1.trx
Reading :: TFTP Server.
..tftp retry wait 0
..tftp retry wait 1
..tftp retry wait 2
..tftp retry wait 3
..tftp retry wait 4
Failed.: Timeout occured
*** command status = -21
CFE> flash -noheader -forceflash : nflash1.trx
Reading :: TFTP Server.
..tftp retry wait 0
..tftp retry wait 1
..tftp retry wait 2
..tftp retry wait 3
..tftp retry wait 4
Failed.: Timeout occured
*** command status = -21
CFE> flash -noheader -forceflash : nflash1.trx
Reading :: TFTP Server.
..tftp retry wait 0
Device eth0: hwaddr 88-D7-F6-44-22-E0, ipaddr 169.254.61.49, mask 255.255.255.0
gateway 169.254.61.49, nameserver not set
Failed.: Timeout occured
*** command status = -21
CFE> flash -noheader -forceflash : nflash1.trx
Reading :: TFTP Server.
..tftp retry wait 0
- last blk -
Done. 38658048 bytes read
Download of 0x24de000 bytes completed
Write kernel and filesystem binary to FLASH
Programming...copysize=38658048, amtcopy=38658048
done. 38658048 bytes written
BCM47XX SYSTEM RESET!!! |
Code: | Digital core power voltage set to 1.0V
Decompressing...done
Detect CPU turbo button...
CFE version 6.37.14.86 (r456083) based on BBP 1.0.37 for BCM947XX (32bit,SP,)
Build Date: 二 4月 22 16:05:16 CST 2014 (raymonddev@raymonddev-vm1210)
Copyright (C) 2000-2008 Broadcom Corporation.
Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
DDR Clock: 400 MHz
Info: DDR frequency set from clkfreq=1000,*800*
Warning: invalid DDR setting of 800 MHz ignored. DDR frequency will be set to 400 MHz.
et1: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.37.14.86 (r456083)
CPU type 0x0: 1000MHz
Tot mem: 262144 KBytes
CFE mem: 0x00F00000 - 0x01795558 (9000280)
Data: 0x00F4DBB4 - 0x00F4E080 (1228)
BSS: 0x00F4E090 - 0x00F93558 (283848)
Heap: 0x00F93558 - 0x01793558 (8388608)
Stack: 0x01793558 - 0x01795558 (8192)
Text: 0x00F00000 - 0x00F4430C (279308)
Committing NVRAM...done
Waiting for wps button release...donDigital core power voltage set to 1.0V
Decompressing...done
Digital core power voltage set to 1.0V
SHMOO VER 1.13
Decompressing...done
Detect CPU turbo button...
CFE version 6.37.14.86 (r456083) based on BBP 1.0.37 for BCM947XX (32bit,SP,)
Build Date: 二 4月 22 16:05:16 CST 2014 (raymonddev@raymonddev-vm1210)
Copyright (C) 2000-2008 Broadcom Corporation.
Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
DDR Clock: 800 MHz
Info: DDR frequency set from clkfreq=1000,*800*
et1: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.37.14.86 (r456083)
CPU type 0x0: 1000MHz
Tot mem: 262144 KBytes
CFE mem: 0x00F00000 - 0x01795558 (9000280)
Data: 0x00F4DBB4 - 0x00F4E080 (1228)
BSS: 0x00F4E090 - 0x00F93558 (283848)
Heap: 0x00F93558 - 0x01793558 (8388608)
Stack: 0x01793558 - 0x01795558 (8192)
Text: 0x00F00000 - 0x00F4430C (279308)
Device eth0: hwaddr 88-D7-F6-44-22-E0, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
Null Rescue Flag.
boot the image...
go load
Loader:raw Filesys:tftp Dev:eth0 File:: Options:(null)
Loading: TFTP Server.
..tftp retry wait 0
Failed.
Could not load :: Timeout occured
Loader:raw Filesys:raw Dev:nflash0.os File: Options:(null)
Loading: .... 4051680 bytes read
Entry at 0x00008000
Closing network.
Starting program at 0x00008000
console [ttyS0] enabled, bootconsole disabled
serial8250.0: ttyS1 at MMIO 0x18000400 (irq = 117) is a 16550
brd: module loaded
loop: module loaded
pflash: found no supported devices
bcmsflash: found no supported devices
Boot partition size = 524288(0x80000)
lookup_nflash_rootfs_offset: offset = 0x200000
nflash: squash filesystem with lzma found at block 28
Creating 4 MTD partitions on "nflash":
0x000000000000-0x000000080000 : "boot"
0x000000080000-0x000000200000 : "nvram"
0x000000200000-0x000004000000 : "linux"
0x00000039d8d0-0x000004000000 : "rootfs"
PPP generic driver version 2.4.2
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPTP driver version 0.8.5
Mirror/redirect action on
u32 classifier
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (3992 buckets, 15968 max)
xt_time: kernel timezone is -0000
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
Registering the dns_resolver key type
Northstar brcmnand NAND Flash Controller driver, Version 0.1 (c) Broadcom Inc. 2012
NAND device: Manufacturer ID: 0x01, Chip ID: 0xf1 (AMD NAND 128MiB 3,3V 8-bit)
## mknod /dev/null: File exists
## mknod /dev/console: File exists
1: set_action 0
Hit ENTER for console...
firmware version: 3.0.0.4.380.69_2
wan_proto: not support FA mode...
fa_mode_adjust(0x18cd): IPTV environment, disable FA mode
[1 preinit:init_nvram +7] init_nvram for model(43)
## Restoring defaults... ##
num_of_mssid_support(0x0088): [mssid] support [3] mssid
done
FA off.
|
-------------------
Router is not 100% work fine, i install OF FW, and merlin, on both LAN2-4 not work, WiFi radio ON signal enable, and i see wifi on smartphone but fail when try connect. WAN OK, internet work. All time LED LAN2 is ON.
In recovery mode only work LAN2 and WAN, LAN1, 3-4 ar not work. |
|