Posted: Mon Jan 09, 2023 9:36 Post subject: New Build - 01/09/2023 - r51275
Welcome to Marvell r51275 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Joined: 12 Dec 2007 Posts: 780 Location: Pittsburgh, PA USA
Posted: Mon Jan 09, 2023 15:32 Post subject:
Router/Version: WRT1900AC v1
File/Kernel: DD-WRT v3.0-r51275 std (01/09/23)
Previous/Reset: DD-WRT v3.0-r51184 std (01/06/23), No reset this time, removed ip6tables rule.
Mode/Status: Gateway (SFE enabled), Access Point, IPV6 (DHCP6 w/ prefix delegation), Entware, DOT via SmartDNS, OpenVPN server, Wireguard Server, Privoxy
Issues/Errors:
After removing the line I added on to the firewall script in the last version based on egc's recommendation:
Code:
ip6tables -I OUTPUT -j ACCEPT
I then did the upgrade to r51275. After upgrade reboot, it probably took about 60 seconds before NTP found the correct time. I waited a few minutes and did another reboot, and NTP came up quickly as expected. Unfortunately, I didn't save the logs on the first reboot. I'll do some more testing to see if it works consistently.
Edit: I did several more reboots and NTP was up by the time I got the GUI to refresh. I'll assume the first reboot after upgrade was an anomaly.
Thanks to egc and to the IPv6 Firewall Comittee. _________________ __________________________
Netgear R7800
DD-WRT v3.0 STD
Linksys WRT1900AC
DD-WRT v3.0 STD
Router Model Linksys WRT1900ACS v2
Firmware Version DD-WRT v3.0-r51275 std (01/09/23)
Kernel Version Linux 4.9.337 #3593 SMP Mon Jan 9 05:36:41 +07 2023 armv7l
Uptime 15:31
update-browser waterfox, I switched from partition 1 from Linksys firmware
connection Type PPPoE - IPv6 Type DHCPv6 with Prefix Delegation 1Gbps
IPv6 Type DHCPv6 with Prefix Delegation-On - Ok
Operating Mode Gateway/AP
Shortcut Forwarding Engine-On
Schedule Reboot-On,
Web Access Protocol - HTTPS,
SSH (public key)-ok
Port Forwarding - Ok,
USB - System Log -Ok
Schedule Reboot - At a Set Time - On
Wireless Interface 5GHz-Wireless Mode AP-Wireless Network Mode-AC/N, Width VHT 80 Mhz-Wireless Channel-36,Short GI, Short Preamble, Single User Beamforming, Radio Scheduling, Enable-WPA2 Personal-CCMP-128 (AES, Regulatory Domain Romania , all-ok
Wireless Interface 2.4GHz-Wireless Mode AP-Wireless Network Mode-N, Width VHT 40 Mhz-Wireless Channel-6, Extension Channel Lower,Short Preamble, Short GI , Radio Scheduling, Enable-WPA2 Personal-CCMP-128 (AES)all-ok _________________ Internet provider https://en.wikipedia.org/wiki/RCS_%26_RDS 1Gbps
WDR3600 rev.1.5 - DD-Wrt
Linksys WRT1900ACS v.2 DD-Wrt/-OpenWrt
Joined: 21 Aug 2019 Posts: 120 Location: Here, There And Everywhere
Posted: Wed Jan 11, 2023 12:38 Post subject:
Router/Version: Linksys WRT1200AC
File/Kernel: Linux 4.9.337 #3593 SMP Mon Jan 9 05:36:41 +07 2023 armv7l
Previous/Reset: r50481 / No
Mode/Status: Wired AP / Working OK
Issues/Errors: No
Router/Version: Linksys WRT1900ACS v2
File: ddwrt-linksys-wrt1900acsv2-webflash.bin
Firmware: DD-WRT v3.0-r51275 std (01/09/23) (prev. DD-WRT v3.0-r51184 std (01/06/23))
Kernel: Linux 4.9.337 #3593 SMP Mon Jan 9 05:36:41 +07 2023 armv7l
Mode: Gateway, SFE enabled, Wifi disabled, Wireguard for external access, WAN to DSL Modem, samba to access USB3-ext4 SSD, Keep Alive reboot 5:00 in the morning
Reset: No
Status: Installed yesterday, one thing found.
Status --> Syslog and its buttons "Previous" and "Next" have some strange characters in them.
This does not happen on my other dd-wrt routers.
CTRL F5 resolves this, until the router is rebooted. Browser: recent Waterfox wf-003 1.0 / G5.1.1 (64-bit)
Load average 0.00, 0.00, 0.00, Temperatures CPU 69.4 °C / WL0 43.0 °C / WL1 44.5 °C
Router/Version: Linksys WRT1900ACS v2
File: ddwrt-linksys-wrt1900acsv2-webflash.bin
Firmware: DD-WRT v3.0-r51275 std (01/09/23) (prev. DD-WRT v3.0-r51184 std (01/06/23))
Kernel: Linux 4.9.337 #3593 SMP Mon Jan 9 05:36:41 +07 2023 armv7l
Mode: Gateway, SFE enabled, Wifi disabled, Wireguard for external access, WAN to DSL Modem, samba to access USB3-ext4 SSD, Keep Alive reboot 5:00 in the morning
Reset: No
Status: Installed yesterday, one thing found.
Status --> Syslog and its buttons "Previous" and "Next" have some strange characters in them.
This does not happen on my other dd-wrt routers.
CTRL F5 resolves this, until the router is rebooted. Browser: recent Waterfox wf-003 1.0 / G5.1.1 (64-bit)
Load average 0.00, 0.00, 0.00, Temperatures CPU 69.4 °C / WL0 43.0 °C / WL1 44.5 °C
I didn't encounter this problem in the picture, well, after configuring the router, I reboot every time! _________________ Internet provider https://en.wikipedia.org/wiki/RCS_%26_RDS 1Gbps
WDR3600 rev.1.5 - DD-Wrt
Linksys WRT1900ACS v.2 DD-Wrt/-OpenWrt
