Issues : Ran into a minor easily resolable issue with this build. It seems something has changed in timing/load order. This affects my setup as follows. When DNSmasq loads, it reads additional hosts file located on the USB drive. In previous builds this worked just fine. in the current build the final dnsmasq load in syslog says cant read the file, those host referenced are not resolvable from endpoints. Restarting DNSMasq after full startup seems to resolve the issue and the log shows # hosts read.
Issues : Ran into a minor easily resolable issue with this build. It seems something has changed in timing/load order. This affects my setup as follows. When DNSmasq loads, it reads additional hosts file located on the USB drive. In previous builds this worked just fine. in the current build the final dnsmasq load in syslog says cant read the file, those host referenced are not resolvable from endpoints. Restarting DNSMasq after full startup seems to resolve the issue and the log shows # hosts read.
yep its the new way how things work....so in some cases you may need to add this extra line at the end of your start up script..(if you have anything there) or may be the usb script if you use the usb instead...
stopservice dnsmasq && sleep 2 && startservice dnsmasq _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 53045 WAP
TP-Link WR1043NDv2 -DD-WRT 54420 Gateway/DoT,Forced DNS,AP Isolation,Ad-Block,Firewall,VPN,x1VLAN
TP-Link WR1043NDv2 -DD-WRT 54475 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear R7800 --DD-WRT 54475 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 54475 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 54475 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
Joined: 17 Jan 2018 Posts: 64 Location: Georgia, USA
Posted: Wed Nov 30, 2022 17:55 Post subject:
Router/Version: Netgear R7800
File/Kernel: DD-WRT v3.0-r50963 std (11/28/22)
Previous/Reset: v3.0-r50927 std (11/21/22) / No reset
Mode/Status: Gateway. Using Vanilla on both radios
Issues/Errors: All appears to be working normally. Up 2+ days.
Have noticed that under Status / Wireless – Channel Quality – the 2.4 GHz channel has dropped to 81%. For the last several versions, and seemingly forever, it has always been around 94%-95% for me.
The 5 GHz channel has remained at 98%. It has always been at 98%-99% for me.
I don’t know if the channel quality has actually changed or if it is now being computed differently.
I have not yet tried switching from Vanilla to DD-WRT _________________ R7800 r53339 std (08/01/23)
Private network on bridge br0 = eth1 (vlan 1) + wlan0 + wlan1.
Guest network on bridge br1 = eth1.4 (vlan 4) + VAPs (wlan0.1 + wlan1.1) for IOT devices
(Roku's, Amazon Echos, smart switches, etc.) and guest.
Noob still finding my way.
swconfig dev switch0 set enable_vlan 1
swconfig dev switch0 vlan 1 set ports "1 2 6"
swconfig dev switch0 vlan 4 set ports "3 4 6t"
swconfig dev switch0 set apply
vconfig add eth1 4
brctl addif br1 eth1.4
ifconfig eth1.4 up
Issues : Ran into a minor easily resolable issue with this build. It seems something has changed in timing/load order. This affects my setup as follows. When DNSmasq loads, it reads additional hosts file located on the USB drive. In previous builds this worked just fine. in the current build the final dnsmasq load in syslog says cant read the file, those host referenced are not resolvable from endpoints. Restarting DNSMasq after full startup seems to resolve the issue and the log shows # hosts read.[/quote]
yep its the new way how things work....so in some cases you may need to add this extra line at the end of your start up script..(if you have anything there) or may be the usb script if you use the usb instead...
May I ask for a little piece of help about In-a-dyn version 2.9.1 and freedns.afraid.org . I think since r50841 I'm getting errors on dns update as follows:
In-a-dyn version 2.9.1 -- Dynamic DNS update client.
alias hnxxxx.mooo.com,eWMxxxxxTzNJxxxxxxdqdHVxxxxxxTRFOjExxxxxxzEy length 60
Failed resolving hostname hnxxxx.mooo.com,eWMxxxxxTzNJxxxxxxdqdHVxxxxxxTRFOjExxxxxxzEy: Name does not resolve
Updating cache for hnxxxx.mooo.com,eWMxxxxxTzNJxxxxxxdqdHVxxxxxxTRFOjExxxxxxzEy, new IP# xx.x6.xx9.xx5
=> ERROR: Could not authenticate.
Both names hnxxxx.mooo.com and freedns.afraid.org are resolved though through the same router and even while connected to the router console via telnet or ssh. Perhaps In-a-dyn 2.9.1 needs slightly different syntax for afraid.org!?
I want to apologize if the topic is wrong, but I did a lot of search so far, unfortunately with no helpful result.
Kind Regards and thank you in advance!
Use the same user/passwd used to access your acc't page & JUST hnxxxx.mooo.com for hostname. Works for me.
PS No issues.
QUESTION: If done properly in the service status box at the end should it be displaying "Updating cache for xxxxxx.mooo.com" (where xxxxxx is my user access name) ???
This is different from previous In-A-Dyn version / DDWRT r50595 release i upgraded from, So I'm just checking if I'm doing it correct.
QUESTION: If done properly in the service status box at the end should it be displaying "Updating cache for xxxxxx.mooo.com" (where xxxxxx is my user access name) ???
This is different from previous In-A-Dyn version / DDWRT r50595 release i upgraded from, So I'm just checking if I'm doing it correct.
I get:
Update forced for alias [host.chosen subdomain], new IP# [current IP]
Updating cache for [host.chosen subdomain]
Try a 'nslookup xxxxxx.mooo.com', which should resolve to [current IP]. If IP's correct, you got it right. _________________ NetGear XR500 - FW Version: DD-WRT v3.0-r53915 std (11/07/23)
Linux 6.1.61 #42 SMP Mon Nov 6 07:30:13 +07 2023 armv7l
Updated from: DD-WRT v3.0-r53843 std (11/01/23) via GUI (FF), NO reset
Gateway: SmartDNS, DDNS (FreeDNS), QoS, IPv4 DHCP, Static leases
AP: 2.4GHz NG-Mixed 40MHz, 5GHz AC/N-Mixed 80MHz, WPA2 w/ AES, MAC filtering, Isolated Guest VAP on wlan1, Vanilla FW
Services: USB Storage, NAS, Samba
Storage: Samsung Portable SSD T7 Shield USB 3.2 2TB, /jffs, /opt, /data (all ext4)
QUESTION: If done properly in the service status box at the end should it be displaying "Updating cache for xxxxxx.mooo.com" (where xxxxxx is my user access name) ???
This is different from previous In-A-Dyn version / DDWRT r50595 release i upgraded from, So I'm just checking if I'm doing it correct.
I get:
Update forced for alias [host.chosen subdomain], new IP# [current IP]
Updating cache for [host.chosen subdomain]
Try a 'nslookup xxxxxx.mooo.com', which should resolve to [current IP]. If IP's correct, you got it right.
Thanks yes it is resolving, Plus I ran command ping xxxxxx.mooo.com and received
--- xxxxxx.mooo.com ping statistics ---
3 packets transmitted, 3 packets received, 0% packet loss
round-trip min/avg/max = 0.103/0.108/0.112 ms
Router/Version: R9000 (x2), R7800 (x4)
File/Kernel: r50963
Previous/Reset: r50786/no
Mode/Status: WDS working
Issues/Errors: Interesting that one R7800 WDS station hostname showed up in the WDS AP in the previous firmware but not now. A reflash still didn't "fix" it. Otherwise, the station works fine. All the other WDS station host names still show up. Status->Wireless->Wireless Nodes->Clients->Name
Router/Version: R7800
File/Kernel: DD-WRT v3.0-r50963 std (11/28/22)
Kernel Version: Linux 4.9.334 #1377 SMP Mon Nov 28 04:13:14 +07 2022 armv7l
Previous/Reset: r50906 / No Reset, CLI Update
Mode/Status: GW(double-nat) & AP / Working Well
Issues/Errors: PuTTY & WinSCP SshHostKeys needed Resetting / none
Services Used: Static WAN,IPv6-6to4,WiFi Vannilla,NTP,2xWG Clients,VAPx,VLANx,BRx,SSH,Syslog,Cron,USB Storage,Entware DNSCrypt v2.1.1
Services Disabled: SPI,QoS,ttraff,SFE,Telnet,NAS,Samba
All running for over 71 hours.
Thank-you BrianSlyer for your Great Work and everyone else who makes DD-WRT Great on the Forum! _________________ Home Network on Telus 1Gb PureFibre - 10GbE Copper Backbone
2x R7800 - Gateway & WiFi & 3xWireGuard - DDWRT r54203 Std k6.1
Off Site 1
R7000 - Gateway & WiFi & WireGuard - DDWRT r54079 Std
E3000 - Station Bridge - DDWRT r49626 Mega K4.4
Off Site 2
R7000 - Gateway & WiFi - DDWRT r52330 Std
E2000 - Wired ISP IPTV PVR Blocker - DDWRT r35531
I just noticed the usb sizes dont seem to make sense or add up under disk space one says 193.6G / 240.5G but under Volume size 465.8 GiB and another says 5.6T / 6.4T and Volume size 12.73 TiB
thought I posted this when I done the upgrade but guess didn't hit submit few hours ago --just now update daughter's EA8500
DD-WRT v3.0-r50963 std (11/28/22)
Linux 4.9.334 #1375 SMP Mon Nov 28 03:29:17 +07 2022 armv7l
GUI upgrade over r50671
tis all good ...yeahuh, had to delete it's know_host stuffs from me laptop cause of ssh key changes just iffin I wanta ssh poke at it
