Posted: Tue Sep 27, 2022 7:44 Post subject: New Build - 09/27/2022 - r50274
Welcome to Broadcom r50274 beta release thread for reporting, feedback to developers & community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• WDS does not work on Broadcom ARM devices (only MIPS<->MIPS) & bridge modes on k4.4 devices may sometimes work
in some configurations for certain builds but are not supported by the bcmdhd driver. Try station or repeater mode but YMMV.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Router/Version: Asus RT-N66U
File: dd-wrt.v24-50274_NEWD-2_K3.x-big-RT-N66U.trx
Firmware: DD-WRT v3.0-r50274 big (09/27/22) (prev. DD-WRT v3.0-r50146 big (09/10/22))
Kernel: Linux 4.4.302-st25 #18966 Tue Sep 27 04:35:08 +07 2022 mips
Mode: Gateway, SFE disabled, Wifi disabled, WAN disabled, Wireguard Endpoint for external VPS, connected via LAN to WRT1900ACS v2, Keep Alive reboot 6:05 in the morning
Reset: No
Status: Installed, ok.
Netgear R8500
Firmware Version DD-WRT v3.0-r50274 std (09/27/22)
Kernel Version Linux 4.4.302-st25 #7602 SMP Tue Sep 27 03:18:37 +07 2022 armv7l
Current Time Tue, 27 Sep 2022 16:20:24
Uptime 1 min
GUI over 50176
Reset: no
Issues: upgraded fine
Router/Version: Asus RT-AC3100
File: asus_rt-ac3100-firmware.trx
Kernel: Linux 4.4.302-st25 #7602 SMP Tue Sep 27 03:18:37 +07 2022 armv7l
Previous/Reset: r50176 / No reset, upgraded via GUI (https)
Mode/Status: Gateway/AP, up 1 hour, 38min
Services Enabled: Ignore WAN DNS, DNSmasq no-resolv, QoS Enabled - FQ-Codel
Issues/Errors: No issues; Working as configured.
---
Router/Version: ASUS RT-AC68U rev B1 (AC1900)
File: asus_rt-ac68u-firmware.trx
Kernel: Linux 4.4.302-st25 #7602 SMP Tue Sep 27 03:18:37 +07 2022 armv7l
Previous/Reset: r50176 / No reset, upgraded via GUI (https)
Mode/Status: Station Bridge, up 7 hours
Issues/Errors: No issues; Working as configured
Thank you BS and all of the other devs who help out to make this firmware great. _________________ ASUS RT-AC3100 AP Merlin 386.12_4
ASUS RT-AC68U Media Bridge/Merlin 386.12_4 (x2)
ASUS RT-AC68U AP r54604
ASUS RT-AC68U Gateway/AP r54604
Edgerouter-4, v2.0.9-hotfix7
Joined: 26 Mar 2013 Posts: 1858 Location: Hung Hom, Hong Kong
Posted: Thu Sep 29, 2022 8:28 Post subject: DD-WRT BS build 50274 and Asus RT-N18U
Router/Version:Asus RT-N18U (rev. A1)
Firmware: DD-WRT v3.0-r50274 std (09/27/22)
Kernel: Linux 4.4.302-st25 #7600 Tue Sep 27 03:04:49 +07 2022 armv7l
Previous: DD-WRT v3.0-r50146 std (09/10/22)
Mode: WAN @ DHCP, Wireless @ AP (Mixed)
Status: Working {
Not 24/7; Not using SFE, CTF, FA, STP, IPv6, VPN, VAP;
DDNS (no-ip.com) OK; SFE + Port-forwarding OK;
USB storage(/jffs, /opt); NAS (ksmbd, lighttpd);
Recursive DNS Unbound(need restart by USB script);
Entware core (CPU: armv71) installed without problem
}
Reset: No RESET during firmware upgrade
File:https://download1.dd-wrt.com/dd-wrtv2/downloads/betas/2022/09-27-2022-r50274/asus-rt-n18u/
Warning(s)/Error(s)
Code:
# grep -i err /var/log/messages | grep -v 'smb'
Jan 1 08:00:12 RT-N18U-HST kern.err kernel: [ 0.000125] smp_twd: clock not found -2
Jan 1 08:00:12 RT-N18U-HST kern.err kernel: [ 2.075581] bcmsflash: found no supported devices
Jan 1 08:00:13 RT-N18U-HST daemon.info mstpd[635]: error, ethtool_get_speed_duplex: Cannot get speed/duplex for eth1: Not supported
Jan 1 08:00:13 RT-N18U-HST daemon.info mstpd[635]: error, ethtool_get_speed_duplex: Cannot get speed/duplex for eth1: Not supported
Jan 1 08:00:13 RT-N18U-HST daemon.info mstpd[635]: error, ethtool_get_speed_duplex: Cannot get speed/duplex for eth1: Not supported
Jan 1 08:00:13 RT-N18U-HST daemon.info mstpd[635]: error, ethtool_get_speed_duplex: Cannot get speed/duplex for eth1: Not supported
Jan 1 08:00:13 RT-N18U-HST daemon.info mstpd[635]: error, ethtool_get_speed_duplex: Cannot get speed/duplex for eth1: Not supported
Sep 29 14:47:04 RT-N18U-HST daemon.info mstpd[635]: error, ethtool_get_speed_duplex: Cannot get speed/duplex for eth1: Not supported
Sep 29 14:47:10 RT-N18U-HST kern.err kernel: [ 39.171020] hub 3-0:1.0: config failed, hub doesn't have any ports! (err -19)
Sep 29 14:47:18 RT-N18U-HST user.info : [lighttpd] : Error on startup, returncode 255
Sep 29 14:47:19 RT-N18U-HST daemon.info mstpd[635]: error, ethtool_get_speed_duplex: Cannot get speed/duplex for eth1: Not supported
Sep 29 14:47:35 RT-N18U-HST user.info : [lighttpd] : Error on startup, returncode 255
_________________ Router: Asus RT-N18U (rev. A1)
Drink, Blink, Stretch! Live long and prosper! May the Force and farces be with you!
Firmware: v3.0-r50274 std (09/27/22)
Router/Version: Netgear R7000 Kernel: Linux 4.4.302-st25 #7596 SMP Tue Sep 27 02:39:30 +07 2022 armv7l
Previous: v3.0-r50176 std (09/15/22)
Mode/Status: AP wired and wireless / Up and running for 1.5 days
Reset: Soft boot before and after upgrade
Temperatures: CPU 61.4 °C / WL0 46.5 °C / WL1 51.4 °C
Issues/Errors: Nothing significant
Updated via webif. No 'nvram erase' this time, last one was in July 2018 (r36325).
I've noticed a reduction in 5 GHz range, but that may be a local issue.
Upload and Download speeds are to ISP spec (500/500 Mbps).
Current basic R7000 setup (subject to change of course):
- Static WAN IP
- Shortcut Forwarding Engine: CTF, Flow Acceleration: Disabled
- STP - Enabled
- IPv4 only, both WAN and LAN
- LAN DHCP Enabled
- Not currently forwarding any ports
- Wireless: AP, Regulatory Domain = CANADA, wl0 Mixed (ch. 6), wl1 AC/N-Mixed (ch. 36, VHT80), AES
- 1 wireless VLAN on wl0
- SNMP disabled, SSH enabled, Telnet disabled
- Firewall enabled, Log Level high
- Syslog: to local server. klogd: disabled.
- USB support - Off
- No custom scripts
- No: ttraf, Tor, VNC, Zabbix, VPN, Radius, OpenVPN
- No: UPnP, DMZ, QoS
- No: Samba, CIFS, JFFS2, miniDLNA, Entware, Optware _________________ Netgear R7000: v3.0-r54248 std (11/29/23)
EdgeRouter-X: EdgeOS v2.0.9-hotfix 7