Posted: Tue Sep 27, 2022 7:48 Post subject: New Build - 09/27/2022 - r50274
Welcome to x86 / x64 r50274 beta release thread for reporting, feedback to developers & community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Joined: 27 Oct 2009 Posts: 70 Location: Woodstock,Ontario
Posted: Tue Sep 27, 2022 11:05 Post subject: new build 50274
This build is no good jammed up one quad card with all the lights on and the 2nd quad only light flashes is my connection but nonresponsive couldn't get anymore info.2nd gen intel i5(2400) 4 GBs of ram intel DQ67sw board two quad pcie intel cards one twin pci card (not used just there in case) previous build (50176) had no issues
Same here. Updated from the previous build on PCEngines APU2 and only thanks to serial connection I found out that iwconfig output was empty, no available interfaces hence no LAN/WAN connection. First I thought it was an upgrade issue, so I flashed a clean image and it was the same. Reverted to the 09-15-2022-r50176 build. _________________ Main HW:
Netgear R7800 @ DD-DWRT r50274 (Router+AP)
- Wireguard client
Joined: 08 May 2018 Posts: 14246 Location: Texas, USA
Posted: Wed Sep 28, 2022 6:33 Post subject:
Serial logs and syslogs with nvram set console_debug=1 would be very helpful in helping BrainSlayer determine the problem. I only interject this as I was asked if there were any (serial) logs. _________________ "Life is but a fleeting moment, a vapor that vanishes quickly; All is vanity"
Contribute To DD-WRT Pogo - A minimal level of ability is expected and needed... DD-WRT Releases 2023 (PolitePol)
DD-WRT Releases 2023 (RSS Everything)
----------------------
Linux User #377467 counter.li.org / linuxcounter.net
Hi, sorry, I have no way of performing the log collection as the mentioned hardware is at my family house and I visit mostly when there is an issue resulting in no internet connection.
I, however, check quickly wether a VM with x86_64 image would reproduce this issue and yes, a virtualbox VM with added two interfaces Intel PRO/1000 based does not detect interfaces on ifconfig, only a default bridge and loopback interface.
I am attaching screens of teh latest build and the previous one for comparison. Once again I apologize but I do not have time right now to play around with trying to export logs from the VM that does not get any network access.
As this issue is easily reproducable in a VM BrainSlayer should be able to track down the cause. _________________ Main HW:
Netgear R7800 @ DD-DWRT r50274 (Router+AP)
- Wireguard client