Posted: Mon Aug 29, 2022 4:50 Post subject: New Build - 08/29/2022 - r49976
Welcome to Marvell r49976 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Noticed a minor issue here that has been in the last few builds. If IPV6 is disabled, and you click on the IPV6 tab, everything is expanded. If you click enable and then disable, everything is collapsed.
If you then click on another tab and then back on the IPV6 tab, it's expanded again. Disable is still selected, so no big deal I guess.
What happens when you click "Cancel Changes", navigate away and then back? _________________ "The woods are lovely, dark and deep,
But I have promises to keep,
And miles to go before I sleep,
And miles to go before I sleep." - Robert Frost
"I am one of the noticeable ones - notice me" - Dale Frances McKenzie Bozzio
Joined: 12 Dec 2007 Posts: 764 Location: Pittsburgh, PA USA
Posted: Mon Aug 29, 2022 19:45 Post subject:
Rickers wrote:
WRT1900ACv1
Noticed a minor issue here that has been in the last few builds. If IPV6 is disabled, and you click on the IPV6 tab, everything is expanded. If you click enable and then disable, everything is collapsed.
For troubleshooting purposes, with IPV6 enabled (DHCP6 with prefix delegation) on the same model of router, I do not see the same issue (Firefox 104.0 under Windows 10). However, I had noticed the same thing on R49677 when I switched from a Hurricane tunnel to my ISP's IPV6. I rolled it back to R49866 at the time, but I also cleared cache on my browser, so I'm not sure which one fixed the problem. Looks correct in R49976. _________________ __________________________
Netgear R7800
DD-WRT v3.0 STD
Linksys WRT1900AC
DD-WRT v3.0 STD
Router/Version: Linksys WRT1900ACSv1 / DD-WRT v3.0-r49976 std (08/29/22)
File/Kernel: ddwrt-linksys-wrt1900acs-webflash.bin / Linux 4.9.326 #3386 SMP Mon Aug 29 02:16:15 +07 2022 armv7l
Previous/Reset: r49934 / No
Mode/Status: Gateway, OpenVPN Client, FreeRadius Server / Uptime 8 min
Issues/Errors: FreeRadius enterprise clients will not connect over WiFi for me on r49976. If I switch back to r49934, FreeRadius enterprise clients connect only if I use the trick of connecting a non-enterprise client after reboot before any enterprise clients attempt to connect, but that trick no longer works for r49976. The last build that let FreeRadius enterprise clients connect without any non-enterprise clients having to connect first was build r49681 (and earlier). Log attached. _________________ My DD-WRT Routers:
Linksys WRT3200ACM - Marvell
Linksys WRT1900ACS - Marvell
Netgear R9000 - Atheros
Netgear R7000 - Broadcom
PC x86-64 VM - Atheros
What happens when you click "Cancel Changes", navigate away and then back?
I went in to try this and it was disabled and collapsed as it should be.
I reset to Factory Defaults and restarted the browser and it's still working properly. It definitely was not collapsed a build or two back, so maybe it was fixed and there was just a browser cache issue when I installed this build.