Posted: Sat Jul 30, 2022 4:52 Post subject: New Build - 07/30/2022 - r49599
Welcome to Marvell r49599 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
- update works good without any problems
- VPN WireGuard
- USB
- DDNS
- CRON "delete directories older > x Days, created by 3xWebCams (stored on128GB SSD)":
e.g. for Cam1: 10 0 * * * root find /tmp/mnt/sda1/Cam1/ -type d -name "20*" -mtime +30 -print0 | xargs -0 rm -r
- Port Forwarding
- FTP
- Samba
- WLAN offline, I use UniFi AP AC LITE as access Point!
- Lan
all OK without error, Thank You for the good work !!!!
Router Model Linksys WRT1900ACS v2
Firmware Version DD-WRT v3.0-r49599 std (07/30/22)
Kernel Version Linux 4.9.325 #3326 SMP Sat Jul 30 03:04:10 +07 2022 armv7l
Current Time Sun, 31 Jul 2022 07:15:34
Uptime 16:46
update- browser-waterfox,I switched directly from the first partition from the original software Linksys,No Reset
connection Type PPPoE - IPv6 Type DHCPv6 with Prefix Delegation- DHCPv6 Server Daemon Enable Daemon, Router Advertisement Daemon (radvd)Enable Daemon,
Schedule Reboot-on,
Web Access Protocol - HTTPS,
Port Forwarding ok,
adblock - 1.Go to Administration -> Go to Administration -> Commands. paste it in “Run Startup”
2.then in the Additional Dnsmasq options add this: addn-hosts=/tmp/mvps 3.Schedule Reboot tuesday 4.reboot router
Wireless Interface 5GHz-Wireless Mode AP-Wireless Network Mode-AC, Width VHT 80 Mhz-Wireless Channel-36,Short GI, Short Preamble,Single User Beamforming, Radio Scheduling, Enable-WPA2 Personal-CCMP-128 (AES, Regulatory Domain Romania , all-ok
Wireless Interface 2.4GHz-Wireless Mode AP-Wireless Network Mode-N/G, Width VHT 40 Mhz-Wireless Channel-6, Extension Channel Lower,Short Preamble, Short GI , Radio Scheduling, Enable-WPA2 Personal-CCMP-128 (AES)all-ok
Issues/Errors: today, after 16 hours of use, I tried to make some changes in the wifi tab and after that I saved and applied the settings, I noticed that ipv6 no longer allocates and disappeared!
If I disable and re-enable ipv6 from the Enable IPv6 tab, everything works fine again, this happens if we do not have No Release on Reconnect active! _________________ Internet provider https://en.wikipedia.org/wiki/RCS_%26_RDS 1Gbps
Linksys WRT1900ACS v.2 DD-Wrt/-OpenWrt
WDR3600 rev.1.5 - DD-Wrt
Router/Version: Linksys WRT1900ACS v2
File: ddwrt-linksys-wrt1900acsv2-webflash.bin
Firmware: DD-WRT v3.0-r49599 std (07/30/22) (prev. DD-WRT v3.0-r49567 std (07/27/22))
Kernel: Linux 4.9.325 #3326 SMP Sat Jul 30 03:04:10 +07 2022 armv7l
Mode: Gateway, SFE enabled, Wifi disabled, Wireguard for external access, WAN to DSL, samba to access USB3-ext4 SSD, Keep Alive reboot 5:00 in the morning
Reset: No
Status: Installed at release, ok. Load average 0.00, 0.00, 0.00, Temperatures CPU 80.3 °C / WL0 53.3 °C / WL1 55.0 °C
