Posted: Wed Jul 20, 2022 10:48 Post subject: New Build - 07/20/2022 - r49531
Welcome to Broadcom r49531 beta release thread for reporting, feedback to developers & community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• DNScrypt 1.95 can still be used in WebUIbut v2 (not compatible) requires Golang and thus Entware. See Trac ticket #6246.
• WDS does not work on Broadcom ARM devices (only MIPS<->MIPS) & bridge modes on k4.4 devices may sometimes work
in some configurations for certain builds but are not supported by the bcmdhd driver. Try client or repeater modes, but YMMV.
• VAPs not working at bootare fixed, both unbridged (r40634) and bridged (r47822). Please test, removestartup commands.
• If startup scripts do not work from USB add delay (wait script), sleep 25 or try Administration -> Commands -> Save USB.
• Broadcom ARM devices if 5 GHz channels are missingvia Telnet/SSH: 'nvram set brcm_unlock=1' 'nvram commit' 'reboot'.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) and applicable configurations to reproduce.
Router/Version: Netgear 8000
File/Kernel: Linux 4.4.302-st14 #6729 SMP Wed Jul 20 07:00:40 +07 2022 armv7l
Previous/Reset: 06/14/2022 - r49197 / No
Mode/Status: RIP2 Router
Issues/Errors: Some RX/TX errors on all 3 radios. Can't see performance impact to the wireless clients _________________ Several NetGears with Broadcom and with Atheros
Mode: RIP2 Router, 2G/5G radios are active, Routed WiFi multiple SSID's/separated by IP subnets.
Remote Syslog, NTP, IPv6 management, WireGuard routed Site-2-Site VPNs
Netgear R8500
Firmware Version DD-WRT v3.0-r49532 std (07/20/22)
Kernel Version Linux 4.4.302-st14 #6730 SMP Wed Jul 20 07:26:07 +07 2022 armv7l
Current Time Wed, 20 Jul 2022 09:06:02
Uptime 3 min
GUI over 49492
Reset: no
Issues: none
Linksys E1200 v2
DD-WRT v3.0-r49531 mega (07/20/22)
Linux 4.4.302-st14 #17424 Wed Jul 20 08:50:21 +07 2022 mips
GUI install over r42602
'dd-wrt.v24-49531_NEWD-2_K3.x_mega-nv64k.bin'
neighbors main gateway -- all worky ok so far
a while back they called me cause stupid thang would just quit...
...seemed to happen when they had company & lots connected to it...
...I just set it to reboot itself 'bout 3:00AM every day & that fixed that.
Maybe r49531 will be as good or better
#
Linksys E2500
DD-WRT v3.0-r49531 mega (07/20/22)
Linux 4.4.302-st14 #17424 Wed Jul 20 08:50:21 +07 2022 mips
GUI install over r49268
'dd-wrt.v24-49531_NEWD-2_K3.x_mega.bin'
just a WAP --- all worky good
Router/Version: Asus RT-N66U
File: dd-wrt.v24-49531_NEWD-2_K3.x-big-RT-N66U.trx
Firmware: DD-WRT v3.0-r49531 big (07/20/22) (prev. DD-WRT v3.0-r49492 big (07/14/22))
Kernel: Linux 4.4.302-st14 #17420 Wed Jul 20 08:45:33 +07 2022 mips
Mode: Gateway, SFE disabled, Wifi disabled, WAN disabled, Wireguard Endpoint for external VPS, connected via LAN to WRT1900ACS v2, Keep Alive reboot 6:05 in the morning
Reset: No
Status: Installed yesterday, ok.
I don't see anything unusual in that syslog output at first glance. I guess I didn't realize that WRT54* devices only have 32k nvram or had forgotten.
I still can't toggle the Klogd service under /Services.asp using the Save button. I haven't done the "nvram erase" yet. Is it really because Klogd is not included in this "mini" variant? If yes, should that option be hidden / greyed out?
Joined: 31 Jul 2021 Posts: 2146 Location: All over YOUR webs
Posted: Thu Jul 21, 2022 18:36 Post subject:
@IONK
IMO if something isn't included in mini/micro builds it should show up, period. Sadly I cannot test similar device, so IDK when or if these things are ifdefd out on cgi. Its easy to check the asp page, but please open a new thread to discuss this and I will try to get attention to this, no promises though.
Router/Version: Netgear R7000 Firmware: DD-WRT v3.0-r49532 std (07/20/22) Kernel: Linux 4.4.302-st14 #6724 SMP Wed Jul 20 05:29:47 +07 2022 armv7l Mode: Gateway, Wireless AP, Static Leases. CTF & FA Enabled. NAT and QOS Off. All services off under Status>Sys-info. Reset: Nope. Previous: 07-09-2022-r49467 Status: Working so far, still testing. wl: 14E4:4360 Temperatures: Did not record. Base CFE: Modified Asus ASUS RT-AC68P/ASUS RT-AC68U (C0 Model CFE V1.3.0.7) Configured as a stock R7000.
Logs.txt
Description:
Full system logs. MAC scrubbed, password scrubbed.