Posted: Mon Jul 04, 2022 10:19 Post subject: New Build - 07/04/2022 - r49418
Welcome to Atheros r49418 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) and applicable configurations to reproduce.
Posted: Mon Jul 04, 2022 11:37 Post subject: 49418
Netgear Nighthawk X10 R9000
Firmware Version DD-WRT v3.0-r49418 std (07/04/22)
Kernel Version Linux 4.9.319 #635 SMP Fri Jun 17 15:05:12 +07 2022 armv7l
Current Time Mon, 04 Jul 2022 05:32:52
Uptime 1 min
GUI over 49392
Reset:no
Issues:none
Linksys EA8500...main gateway
DD-WRT v3.0-r49418 std (07/04/22)
Linux 4.9.319 #1048 SMP Wed Jun 29 03:17:35 +07 2022 armv7l
GUI install over r49392
all good -- up 11:37
#
Netgear WNDR3700 V4
DD-WRT v3.0-r49418 std (07/04/22)
Linux 3.18.140-d6 #147453 Mon Jul 4 09:31:20 +07 2022 mips
scp 'firmware.bin' over r49392
all good-- up 9:04
Router Model: TP-Link TL-WR1043ND
Firmware Version: DD-WRT v3.0-r49418 std (07/04/22)
Previous: DD-WRT v3.0-r49392 std (06/29/22)
Kernel Version: Linux 3.10.108-d11 #111711 Mon Jul 4 07:26:26 +07 2022 mips
Mode: Gateway/AP
Reset: No
Status: OK
Uptime: <~1h
Issues/Errors: None
Speedtest.net Results: Wired 51.83 D 9.98 U / Wireless 13.57 D 9.86 U (vintage Ath5k in x86_32 MacBook ~2008 model)
Flash went through via webUI on Firefox ESR on Debian 10 Mate without a hitch. Will continue testing functionality of features and report back should any issues arise. _________________ "The woods are lovely, dark and deep,
But I have promises to keep,
And miles to go before I sleep,
And miles to go before I sleep." - Robert Frost
"I am one of the noticeable ones - notice me" - Dale Frances McKenzie Bozzio
Joined: 16 Mar 2019 Posts: 353 Location: Szczecin, Poland EU
Posted: Tue Jul 05, 2022 9:09 Post subject:
The TP-Link TL-WDR3600 v1.5 have poor WAN performance. When the SFE feature is enabled download speed is very similar when SFE is disabled. I think SFE in this model is unoptimized. I try to make optimal configuration on my device. In command line I'm open nvram show and there are active interfaces like eth1, eth2 to eth10... When I'm use only 5GHz for WIFI, WAN port and one PC connected via rj45. When I'm execute command ifconfig I see only eth0 and other interfaces are absent. Why that variables is exist ? The same situation is br1 or for example vlan5... When I try erase variables with nvram unset <var name> and then nvram commit, after reboot variables exist again. Other values I can change or delete, but that eth, br1, vlans come back after reboot. I think router haven't optimal configuration, but I can't change this and not all options is available via gui. For example haven't simply change ttl or GUI logout button...
Joined: 18 Mar 2014 Posts: 12882 Location: Netherlands
Posted: Tue Jul 05, 2022 9:21 Post subject:
Router Model: Linksys EA8500
Firmware Version: DD-WRT v3.0-r49418M Community Build by EGC (07/05/22)
Upgraded from: DD-WRT v3.0-r49268M Community Build by EGC (06/19/22)
Reset: No not this time
Status: Up and running for 4 hours, basic setup as Gateway, static leases, 2.4 GHz and 5 GHz switched off, OpenVPN server working, WireGuard Server working (multiple clients e.g. phone, laptop and site-to-site connection with remote location), NAS and Samba working, Avahi and Avahi-utils working