Posted: Thu Jun 23, 2022 5:00 Post subject: New Build - 06/23/2022 - r49326
Welcome to Atheros r49326 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) and applicable configurations to reproduce.
Posted: Thu Jun 23, 2022 12:37 Post subject: 49326
Netgear Nighthawk X10 R9000
Firmware Version DD-WRT v3.0-r49326 std (06/23/22)
Kernel Version Linux 4.9.319 #635 SMP Fri Jun 17 15:05:12 +07 2022 armv7l
Current Time Thu, 23 Jun 2022 06:33:33
Uptime 1 min
GUI over 49289
Reset:no
Issues: none
Status: Up and running for 2 hours, set up as Station Bridge (routed) for testing
Errors: Cannot get an unbridged VAP working probably limitation of this kind of setup, otherwise working.
As the warning says: Do not use this "Station Bridge (routed)" mode unless lives are at stake
Router Model: TP-Link TL-WR1043ND
Firmware Version: DD-WRT v3.0-r49326 std (06/23/22)
Previous: DD-WRT v3.0-r49289 std (06/22/22)
Kernel Version: Linux 3.10.108-d11 #111116 Thu Jun 23 06:00:20 +07 2022 mips
Mode: Gateway/AP
Reset: No
Status: OK
Uptime: ~45m-1h
Issues/Errors: None
Speedtest.net Results: Wired 51.83 D 9.98 U / Wireless 13.57 D 9.86 U (vintage Ath5k in x86_32 MacBook ~2008 model)
Flash went through via webUI on Firefox ESR on Debian 10 Mate without a hitch. Will continue testing functionality of features and report back should any issues arise. _________________ "The woods are lovely, dark and deep,
But I have promises to keep,
And miles to go before I sleep,
And miles to go before I sleep." - Robert Frost
"I am one of the noticeable ones - notice me" - Dale Frances McKenzie Bozzio
Router Model TP-Link WR1043ND V2
Firmware Version DD-WRT v3.0-r49326 std (06/23/22)
Kernel Version Linux 3.18.140-d6 #146795 Thu Jun 23 07:02:57 +07 2022 mips
update: CLI
reset: NO
mode: Gateway
status: Operational 13h+
errors: Nothing new, yet...
openssl has new version can we get it updated...??
openssl-1.1.1p.tar.gz
as well my 1043v2 doesn't have ssl folder under /ect ..so if ssl is not compiled for this router...(8mb Flash)??
why i can see OpenVpn its using it
Jan 1 00:00:30 TPLINK-WR1043NDv2 daemon.notice openvpn[1680]: library versions: OpenSSL 1.1.1o 3 May 2022, LZO 2.10
so, where is ssl located ? or ca-bundle.crt ?? _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55630 WAP
TP-Link WR1043NDv2 -DD-WRT 55723 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55779 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55819 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55779 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
Router/Version: TP-Link ARCHER-C7 v5 (ARCHERC7v5)
File/Kernel: Linux 3.18.140-d6 #146805 Thu Jun 23 07:21:57 +07 2022 mips
Previous/Reset: DD-WRT v3.0-r44715 std (11/03/20)
Status: OK
Issues/Errors: None so far
Mode: Gateway/AP
Reset: Yes
Uptime: +1h
I finally updated from a very old version. It seems to be working fine. Thanks!!
Since you are updating from an 18+ month old version, you may want to reset DD-WRT and set your configuration manually. There have been a lot of changes. _________________ Netgear R9000
DD-WRT v3.0-r55819 std (04/17/24)
Linux 4.9.337 #722 SMP Wed Apr 17 04:16:49 +07 2024 armv7l
Gateway, AP, DNSMasq, Clock 2000MHz
VAP on wlan1 for internet devices
IPv4 & IPv6 (Prefix Delegation)
Static Leases & DHCP
CloudFlare, no SFE, SmartDNS, no QoS
2.4GHz: Vanilla, Airtime Fairness, NG-Mixed, ACK Timing 3150, WPA2 w/AES & WPA3
5GHz: Vanilla, Airtime Fairness, AC/N Mixed, ACK Timing 3150, WPA2 w/AES & WPA3
2 Netgear AX1800 WiFi Mesh Extenders
Xfinity 1.2Gbps/35Mbps
Since you are updating from an 18+ month old version, you may want to reset DD-WRT and set your configuration manually. There have been a lot of changes.
For someone that stays pretty current and often flashes the latest build without performing a "nvram erase && reboot" and configuration, how often is a erase and configuration recommended? Does DD-WRT generally transition a configuration gracefully when flashing over a recent version, or should a user erase and reconfigure after a certain period of time or a certain number of flashes? Generally, I won't erase and configure unless I have waited a long time between flashes, I am having a problem, or I plan to post about a problem and am asking for help.
Since you are updating from an 18+ month old version, you may want to reset DD-WRT and set your configuration manually. There have been a lot of changes.
Thanks for the advice! I did in fact a reset and reconfigured everything from scratch. Some hours have passed and no issues found. I even took the time to configure properly the 2 and 5 ghz channels this time and it's working fantastic.