Linksys WRT3200ACM with Linksys Velop WHW03v2

Post new topic   Reply to topic    DD-WRT Forum Index -> Marvell MVEBU based Hardware (WRT1900AC etc.)
Author Message
elaroche
DD-WRT Novice


Joined: 14 Jun 2022
Posts: 2

PostPosted: Tue Jun 14, 2022 11:14    Post subject: Linksys WRT3200ACM with Linksys Velop WHW03v2 Reply with quote
Hi,

first I'd like to thank this community and also the main contributor to the various firmware, the job is really amazing.
I've search the forum and couldn't find the answer, the closest I could find was a DNS resolve getting denied but it didn't help.

So let me explain my issue which and I hope someone can help me.
I've flash my WRT3200ACM with the Firmware: DD-WRT v3.0-r44715 std (11/03/20).
This router has a PPoE role. I'm not using it's wifi (as I couldn't found how to mesh it).
On this router is connected my 3 Velops WHW03 in bridge mode (they are then DHCP clients) the create a meshed wifi.

Schema:
(Internet) ---- (WRT3200ACM PPoE) ---- (Main velop WHW) -= WIFI WIFI--many devices including other velop nodes


The velops has leds to know the status (connected, disconnected, reconnecting, etc.).
They are mainly displaying "disconnected" even if I can connect to them and access internet. I would say that the networks works properly except that it says "not connected".

It is a problem because the mesh logic doesn't work as the nodes don't share the best access point for my device.

I looks like Linksys is checking a specific domain name that DD-WRT blocks.
If I remove the WRT3200ACM with DD-WRT an connect directly the Velops as a PPoE modem, everything works fine.

Any ideas ?
Thank you.

Note: I'm not English so apologies if I did mistakes or if I hardly understandable.
Sponsor
blkt
DD-WRT Guru


Joined: 20 Jan 2019
Posts: 5660

PostPosted: Tue Jun 14, 2022 11:20    Post subject: Reply with quote
New Build - 06/14/2022 - r49197 -> /linksys-wrt3200acm/ddwrt-linksys-wrt3200acm-webflash.bin

Afterwards, Administration -> Factory Defaults, reset button 10 seconds or nvram erase && reboot.


Last edited by blkt on Tue Jun 14, 2022 11:23; edited 1 time in total
Alozaros
DD-WRT Guru


Joined: 16 Nov 2015
Posts: 6409
Location: UK, London, just across the river..

PostPosted: Tue Jun 14, 2022 11:23    Post subject: Reply with quote
to the ddwrt is only router in gateway mode on its own subnet with dhcp and dns, with no wifi and you use its LAN ports to connect wi-fi ap's
or router is in router/switch mode with no dhcp or dns..and its
its basically a bridge between your modem and the wifi ap connected via LAN ports... ?

not very clear your set up ? (4me)
as well 44715 very old and bad build...full with flaws and unpatched bugs...update your build the last build currently is 49197

_________________
Atheros
TP-Link WR740Nv1 ---DD-WRT 55179 WAP
TP-Link WR1043NDv2 -DD-WRT 55303 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55460 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55460 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55363 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913


Last edited by Alozaros on Tue Jun 14, 2022 11:24; edited 1 time in total
egc
DD-WRT Guru


Joined: 18 Mar 2014
Posts: 12837
Location: Netherlands

PostPosted: Tue Jun 14, 2022 11:23    Post subject: Reply with quote
Welcome to the forum.

Unfortunately you are posting in the wrong forum and using an outdated and no longer supported build.

See the forum guidelines with helpful pointers about how to research your router, where and what firmware to download, where and how to post and many other helpful tips:
https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=324087

Current build is 49197.

Upgrade first and *after* upgrade reset to defaults and put settings in manually never restore from a backup (to a different build).

Only set your PPPoE credentials, and disable wireless, leave everything else at default.

It is possible that the Velop also uses 192.168.1.1 as IP address so to be sure you are using something different change the local IP address from the WRT3200 from 192.168.1.1 to 192.168.13.1
This is on Setup page

DDWRT does not block any domains

Moved this to the appropriate Marvell forum

_________________
Routers:Netgear R7000, R6400v1, R6400v2, EA6900 (XvortexCFE), E2000, E1200v1, WRT54GS v1.
Install guide R6400v2, R6700v3,XR300:https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=316399
Install guide R7800/XR500: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=320614
Forum Guide Lines (important read):https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=324087
elaroche
DD-WRT Novice


Joined: 14 Jun 2022
Posts: 2

PostPosted: Tue Jun 14, 2022 22:30    Post subject: Reply with quote
Thank you everyone and thank you for the admin for the move.

I'll try that, I guess the page for the router was outdated as I downloaded the latest firmware from there.
I'll do the upgrade and follow your advices and retry. It will need to wait for the weekend as I'm using it to work.

@Alozaros : yes the WRT3200ACM is the modem/router with DHCP, no wifi and the velop AP is connected through an ethernet port.

Thank you again, greatly appreciated.
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Index -> Marvell MVEBU based Hardware (WRT1900AC etc.) All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum