Posted: Sat Jun 04, 2022 11:50 Post subject: New Build - 06/04/2022 - r49081
Welcome to Broadcom r49081 beta release thread for reporting, feedback to developers & community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• DNScrypt 1.95 can still be used in WebUIbut v2 (not compatible) requires Golang and thus Entware. See Trac ticket #6246.
• WDS does not work on Broadcom ARM devices (only MIPS<->MIPS) & bridge modes on k4.4 devices may sometimes work
in some configurations for certain builds but are not supported by the bcmdhd driver. Try client or repeater modes, but YMMV.
• VAPs not working at bootare fixed, both unbridged (r40634) and bridged (r47822). Please test, removestartup commands.
• If startup scripts do not work from USB add delay (wait script), sleep 25 or try Administration -> Commands -> Save USB.
• Broadcom ARM devices if 5 GHz channels are missingvia Telnet/SSH: 'nvram set brcm_unlock=1' 'nvram commit' 'reboot'.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) and applicable configurations to reproduce.
Router/Version: Trendnet TEW-811DRU / DD-WRT v3.0-r49081 mini (06/04/22)
File/Kernel: trendnet-811dru-webflash.bin / Linux 4.4.302-st14 #6225 Sat Jun 4 08:45:55 +07 2022 armv7l
Previous/Reset: DD-WRT v3.0-r48996 mini (05/30/22) / no
Mode/Status: Client AP/ Booted clean, CPU 84.7 °C / WL0 54.8 °C / WL1 59.0 °C , uptime 4 mins
temps seem better than previously, UI ok - stable so far
Issues/Errors: none yet, thx devs
Joined: 01 Dec 2021 Posts: 289 Location: Maryland, United States
Posted: Sun Jun 05, 2022 19:57 Post subject:
Bushant you say you just upgraded to the current build but in the post directly above your post kernel-panic69 states that build is not compatible with R6200v2 since it has different architecture. How did you do it?
Bushant you say you just upgraded to the current build but in the post directly above your post kernel-panic69 states that build is not compatible with R6200v2 since it has different architecture. How did you do it?
From OEM I used firmware from myopenrouter.com to first get on DD-WRT.
Then was able to upgrade via GUI using <Kong>'s v24-K3_AC_ARM_STD files.
When those ended I have to put the router in recovery mode and tftp the R6250 files.
Netgear R6700 v3 – Client Bridge
Firmware Version: DD-WRT v3.0-r49081 std (06/04/22)
Kernel Version: Linux 4.4.302-st14 #6222 SMP Sat Jun 4 08:21:03 +07 2022 armv7l
Wireless: Vanilla
Temperatures: CPU 71.4 °C / WL1 55.7 °C
Current Time: Sun, 05 Jun 2022 17:34:43
Uptime: 1 day, 2:33
Reset: No
GUI install over 48971
Installed using Brave browser over wireless
No issues
Thank you BS and thanks you gurus for your guides and wisdom _________________ Netgear XR500 - Gateway
R6700 v3 - Station Bridge
Firmware: v3.0-r49081 std (06/04/22)
Router/Version: Netgear R7000 Kernel: Linux 4.4.302-st14 #6222 SMP Sat Jun 4 08:21:03 +07 2022 armv7l
Previous: v3.0-r48996 std (05/30/22)
Mode/Status: AP wired and wireless / Up and running for 1.5 days
Reset: Soft boot before and after upgrade
Temperatures: CPU 60.2 °C / WL0 46.0 °C / WL1 51.0 °C
Issues/Errors: Nothing significant
Updated via webif. No 'nvram erase' this time, last one was in July 2018 (r36325).
Upload and Download speeds are to ISP spec (500/500 Mbps).
Current basic R7000 setup (subject to change of course):
- Static WAN IP
- Shortcut Forwarding Engine: CTF, Flow Acceleration: Disabled
- STP - Enabled
- IPv4 only, both WAN and LAN
- LAN DHCP Enabled
- Not currently forwarding any ports
- Wireless: AP, Regulatory Domain = CANADA, wl0 Mixed (ch. 6), wl1 AC/N-Mixed (ch. 36, VHT80), AES
- 1 wireless VLAN on wl0
- SNMP disabled, SSH enabled, Telnet disabled
- Firewall enabled, Log Level high
- Syslog: to local server. klogd: disabled.
- USB support - Off
- No custom scripts
- No: ttraf, Tor, VNC, Zabbix, VPN, Radius, OpenVPN
- No: UPnP, DMZ, QoS
- No: Samba, CIFS, JFFS2, miniDLNA, Entware, Optware _________________ Netgear R7000: v3.0-r54248 std (11/29/23)
EdgeRouter-X: EdgeOS v2.0.9-hotfix 7