Posted: Wed May 11, 2022 7:51 Post subject: [SOLVED] Archer C7 v5 Openwrt Ok; DD-wrt KO!!
Hi.
Since 6 years i have an Archer C7 v2 with Dd-wrt its wonderfull!!! Lol
I used it an AP mode for extend Wifi on 1st floor via Rj45 cable
Thanks for all the work!!!
My provider router ( french Freebox) have a bad wifi signal.
I have buy on Amazon an new Archer C7v5.
I have see the wiki.
1st reset factory
Used firmware c7v5 factory but the firm is recongnise not correct by tp-link apply....
I tested several times...
After i used Openwrt firm and its ok
The C7v5 works fine!!
But i want DD-wrt firm.
I tested upload Dd-wrt firm in Openwrt but alarm before flash : firm error...
I have forced install and Archer was bricked....
Tks for Tftp process!!!!!
Any body can tested the Archer C7v5 stock in upload?
Other question:
The C7V5 is mesh
Can use mesh option with Dd-wrt firm?
Hi.
Tks for your answer.
I have read the other post and endly i have installed Dd-wrt on my C7v5!!!
I have a problem that pops up.
I can configure it as I wish (AP mode to extend my Wifi)
but after 5-10min
I lose access to the administration of the router and access to the internet.
Then I recover the connection.... and that in a loop.
suddenly I installed Openwrt again and same phenomenon.
I obviously do a factory reset before and after each firm upload.
Is it a hardware failure?
what can I do?
thank you
Joined: 31 Jul 2021 Posts: 2146 Location: All over YOUR webs
Posted: Wed May 11, 2022 16:35 Post subject:
Glad to hear it's unbricked.
Without seeing syslogs, wouldn't know, and the exact setup you made via attached screenshots, screenshots of all your setup are more important to try catch anything.
On another thread some person had assigned static IP's and the static IP for router was I think same for his PC, so that caused loss of HTTP(s) interface access.
Syslog is enabled on services tab.
One note about resets, its better to reset the nvram via terminal. When you switch from one FW type to the other, better to do a reset before and one after.
Avoid keep doing this back and forth FW swaps and resets, flash nand does wear out with excessive writes, that said, Brainslayer has an archer which has been flashed 2000+ times and still chugging along.
Another thing is, you could always open a terminal and run
Code:
restart httpd
If that doesnt get your webinterface back, its likely something with setup or idk.
Also do flash the latest dd-wrt r48810, not some ancient build found in some router database belonging to dd-wrt, these are outdated and not to be used.
Hello.
I was in original firmw of 2018 which allows to install DD-Wrt.
I installed the firm available in your link and impossible to restart the router.
Even in TFTP impossible to unbrick it
I requested an exchange from Amazon.
I'll let you know when I get the new one
thanks again
Hello.
I thank Amazon because I have already received the new Archer C7 v5 router!
I was able to directly install the firm factory available in your upload dated May 13, 2022
On the other hand, I have problems with the operation of the 2 Archer C7s at the same time (the old V2 and the new V5)
the 2 are in fixed IP
v2: 192.168.1.1
v5:192.168.1.2
at the beginning I had put the same SSID in 2.4g and 5g.
then I changed the SSIDs; always problems
First I no longer have access to the 2 routers when I connect the internet to Lan V2 then I connect Lan V2 to Lan V5
and I have access to few websites.
By disabling the V5 I find full internet!
if I use the internet on the Lan V5, my Firestick connects to the internet, however my PC still does not connect to a few websites.....
Here is an extract from the syslog
[code:1:896c224258]System Log
Jan 1 01:12:02 DD-WRT syslog.info syslogd started: BusyBox v1.35.0
Jan 1 01:12:03 DD-WRT user.info : [klogd] : daemon successfully started
Jan 1 01:12:03 DD-WRT kern.notice kernel: klogd started: BusyBox v1.35.0 (2022-05-13 08:17:02 +07)
Jan 1 01:12:03 DD-WRT kern.debug kernel: [ 14.290000] ath: country maps to regdmn code: 0x3a
Jan 1 01:12:03 DD-WRT kern.debug kernel: [ 14.290000] ath: Country alpha2 being used: US
Jan 1 01:12:03 DD-WRT kern.debug kernel: [ 14.290000] ath: Regpair used: 0x3a
Jan 1 01:12:03 DD-WRT kern.debug kernel: [ 14.290000] ath: regdomain 0x8348 dynamically updated by user
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 27.230000] device wlan0 entered promiscuous mode
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 27.230000] br0: port 2(wlan0) entered forwarding state
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 27.240000] br0: port 2(wlan0) entered forwarding state
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 27.520000] ath10k_pci 0000:00:00.0: boot upload otp to 0x1234 len 6209
Jan 1 01:12:03 DD-WRT kern.warn kernel: [ 27.550000] ath10k_pci 0000:00:00.0: otp stream is empty, using board.bin contents
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 28.420000] ath10k_pci 0000:00:00.0: Init Max Stations to 128
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 28.440000] ath10k_pci 0000:00:00.0: P 135 V 16 T 433
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 28.450000] ath10k_pci 0000:00:00.0: alloc rem: 9492 iram: 42308
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 28.460000] ath10k_pci 0000:00:00.0: wmi event ready sw_version 0x41000061 abi_version 1 mac_addr e8:48:b8:c1:a5:1a status 0
Jan 1 01:12:03 DD-WRT kern.warn kernel: [ 28.470000] ath10k_pci 0000:00:00.0: pdev param 0 not supported by firmware
Jan 1 01:12:03 DD-WRT kern.warn kernel: [ 28.490000] ath10k_pci 0000:00:00.0: failed to set vdev 0 tx encap mode: -122
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 28.500000] ath10k_pci 0000:00:00.0: Mac CLK 88
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 29.160000] br0: port 1(vlan1) entered forwarding state
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 35.510000] ath10k_pci 0000:00:00.0: boot upload otp to 0x1234 len 6209
Jan 1 01:12:03 DD-WRT kern.warn kernel: [ 35.540000] ath10k_pci 0000:00:00.0: otp stream is empty, using board.bin contents
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 36.420000] ath10k_pci 0000:00:00.0: Init Max Stations to 128
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 36.430000] ath10k_pci 0000:00:00.0: P 135 V 16 T 433
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 36.440000] ath10k_pci 0000:00:00.0: alloc rem: 9492 iram: 42308
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 36.450000] ath10k_pci 0000:00:00.0: wmi event ready sw_version 0x41000061 abi_version 1 mac_addr e8:48:b8:c1:a5:1a status 0
Jan 1 01:12:03 DD-WRT kern.warn kernel: [ 36.460000] ath10k_pci 0000:00:00.0: pdev param 0 not supported by firmware
Jan 1 01:12:03 DD-WRT kern.warn kernel: [ 36.480000] ath10k_pci 0000:00:00.0: failed to set vdev 0 tx encap mode: -122
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 36.550000] device wlan1 entered promiscuous mode
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 36.550000] br0: port 3(wlan1) entered forwarding state
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 36.560000] br0: port 3(wlan1) entered forwarding state
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 37.330000] device vlan2 entered promiscuous mode
Jan 1 01:12:03 DD-WRT kern.warn kernel: [ 40.640000] ipt_TRIGGER: module license 'unspecified' taints kernel.
Jan 1 01:12:03 DD-WRT kern.warn kernel: [ 40.650000] Disabling lock debugging due to kernel taint
Jan 1 01:12:03 DD-WRT kern.alert kernel: [ 41.310000] fast-classifier (PBR safe v2.1.6b): starting up
Jan 1 01:12:03 DD-WRT kern.alert kernel: [ 41.320000] fast-classifier: registered
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 41.590000] ip6_tables: (C) 2000-2006 Netfilter Core Team
Jan 1 01:12:03 DD-WRT kern.notice kernel: [ 41.810000] random: nonblocking pool is initialized
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 42.270000] device vlan2 left promiscuous mode
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 42.280000] br0: port 2(wlan0) entered forwarding state
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 51.600000] br0: port 3(wlan1) entered forwarding state
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 100.960000] nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead.
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 219.740000] device vlan1 left promiscuous mode
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 219.750000] device eth0 left promiscuous mode
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 219.750000] br0: port 1(vlan1) entered disabled state
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 219.790000] device wlan0 left promiscuous mode
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 219.790000] br0: port 2(wlan0) entered disabled state
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 219.800000] device wlan1 left promiscuous mode
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 219.810000] br0: port 3(wlan1) entered disabled state
Jan 1 01:12:03 DD-WRT kern.alert kernel: [ 220.130000] fast-classifier: shutting down
Jan 1 01:12:03 DD-WRT kern.alert kernel: [ 220.240000] fast-classifier (PBR safe v2.1.6b): starting up
Jan 1 01:12:03 DD-WRT kern.alert kernel: [ 220.250000] fast-classifier: registered
Jan 1 01:12:03 DD-WRT kern.warn kernel: [ 221.460000] ath10k_pci 0000:00:00.0: could not get mac80211 beacon
Jan 1 01:12:03 DD-WRT kern.warn kernel: [ 221.570000] ath10k_pci 0000:00:00.0: could not get mac80211 beacon
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 221.800000] ath10k_pci 0000:00:00.0: boot upload otp to 0x1234 len 6209
Jan 1 01:12:03 DD-WRT kern.warn kernel: [ 221.830000] ath10k_pci 0000:00:00.0: otp stream is empty, using board.bin contents
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 222.710000] ath10k_pci 0000:00:00.0: Init Max Stations to 128
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 222.730000] ath10k_pci 0000:00:00.0: P 135 V 16 T 433
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 222.740000] ath10k_pci 0000:00:00.0: alloc rem: 9492 iram: 42308
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 222.740000] ath10k_pci 0000:00:00.0: wmi event ready sw_version 0x41000061 abi_version 1 mac_addr e8:48:b8:c1:a5:1a status 0
Jan 1 01:12:03 DD-WRT kern.warn kernel: [ 222.760000] ath10k_pci 0000:00:00.0: pdev param 0 not supported by firmware
Jan 1 01:12:03 DD-WRT kern.warn kernel: [ 222.780000] ath10k_pci 0000:00:00.0: failed to set vdev 0 tx encap mode: -122
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 223.160000] device br0 entered promiscuous mode
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 223.250000] device vlan1 entered promiscuous mode
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 223.260000] device eth0 entered promiscuous mode
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 223.330000] device vlan2 entered promiscuous mode
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 223.340000] br0: port 2(vlan2) entered forwarding state
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 223.350000] br0: port 2(vlan2) entered forwarding state
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 223.350000] br0: port 1(vlan1) entered forwarding state
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 223.360000] br0: port 1(vlan1) entered forwarding state
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 223.370000] device br0 left promiscuous mode
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 223.380000] device br0 entered promiscuous mode
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 223.390000] device br0 left promiscuous mode
Jan 1 01:12:03 DD-WRT kern.debug kernel: [ 223.530000] ath: EEPROM regdomain: 0x8348
Jan 1 01:12:03 DD-WRT kern.debug kernel: [ 223.530000] ath: EEPROM indicates we should expect a country code
Jan 1 01:12:03 DD-WRT kern.debug kernel: [ 223.530000] ath: doing EEPROM country->regdmn map search
Jan 1 01:12:03 DD-WRT kern.debug kernel: [ 223.530000] ath: country maps to regdmn code: 0x3a
Jan 1 01:12:03 DD-WRT kern.debug kernel: [ 223.530000] ath: Country alpha2 being used: US
Jan 1 01:12:03 DD-WRT kern.debug kernel: [ 223.530000] ath: Regpair used: 0x3a
Jan 1 01:12:03 DD-WRT kern.debug kernel: [ 223.530000] ath: regdomain 0x8348 dynamically updated by user
Jan 1 01:12:03 DD-WRT kern.debug kernel: [ 223.530000] ath: EEPROM regdomain: 0x8348
Jan 1 01:12:03 DD-WRT kern.debug kernel: [ 223.530000] ath: EEPROM indicates we should expect a country code
Jan 1 01:12:03 DD-WRT kern.debug kernel: [ 223.530000] ath: doing EEPROM country->regdmn map search
Jan 1 01:12:03 DD-WRT kern.debug kernel: [ 223.530000] ath: country maps to regdmn code: 0x3a
Jan 1 01:12:03 DD-WRT kern.debug kernel: [ 223.530000] ath: Country alpha2 being used: US
Jan 1 01:12:03 DD-WRT kern.debug kernel: [ 223.530000] ath: Regpair used: 0x3a
Jan 1 01:12:03 DD-WRT kern.debug kernel: [ 223.530000] ath: regdomain 0x8348 dynamically updated by user
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 235.630000] device wlan0 entered promiscuous mode
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 235.630000] br0: port 3(wlan0) entered forwarding state
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 235.640000] br0: port 3(wlan0) entered forwarding state
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 238.400000] br0: port 2(vlan2) entered forwarding state
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 238.400000] br0: port 1(vlan1) entered forwarding state
Jan 1 01:12:03 DD-WRT kern.warn kernel: [ 238.730000] ath10k_pci 0000:00:00.0: wmi command 36870 timeout, restarting hardware
Jan 1 01:12:03 DD-WRT kern.warn kernel: [ 238.730000] ath10k_pci 0000:00:00.0: ani_enable failed from debugfs: -11
Jan 1 01:12:03 DD-WRT kern.warn kernel: [ 238.740000] ath10k_pci 0000:00:00.0: cannot restart a device that hasn't been started
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 238.900000] ath10k_pci 0000:00:00.0: boot upload otp to 0x1234 len 6209
Jan 1 01:12:03 DD-WRT kern.warn kernel: [ 238.930000] ath10k_pci 0000:00:00.0: otp stream is empty, using board.bin contents
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 239.810000] ath10k_pci 0000:00:00.0: Init Max Stations to 128
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 239.820000] ath10k_pci 0000:00:00.0: P 135 V 16 T 433
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 239.840000] ath10k_pci 0000:00:00.0: alloc rem: 9492 iram: 42308
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 239.840000] ath10k_pci 0000:00:00.0: wmi event ready sw_version 0x41000061 abi_version 1 mac_addr e8:48:b8:c1:a5:1a status 0
Jan 1 01:12:03 DD-WRT kern.warn kernel: [ 239.850000] ath10k_pci 0000:00:00.0: pdev param 0 not supported by firmware
Jan 1 01:12:03 DD-WRT kern.warn kernel: [ 239.870000] ath10k_pci 0000:00:00.0: failed to set vdev 0 tx encap mode: -122
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 246.890000] ath10k_pci 0000:00:00.0: boot upload otp to 0x1234 len 6209
Jan 1 01:12:03 DD-WRT kern.warn kernel: [ 246.920000] ath10k_pci 0000:00:00.0: otp stream is empty, using board.bin contents
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 247.930000] ath10k_pci 0000:00:00.0: Init Max Stations to 128
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 247.950000] ath10k_pci 0000:00:00.0: P 135 V 16 T 433
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 247.960000] ath10k_pci 0000:00:00.0: alloc rem: 9492 iram: 42308
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 247.970000] ath10k_pci 0000:00:00.0: wmi event ready sw_version 0x41000061 abi_version 1 mac_addr e8:48:b8:c1:a5:1a status 0
Jan 1 01:12:03 DD-WRT kern.warn kernel: [ 247.980000] ath10k_pci 0000:00:00.0: pdev param 0 not supported by firmware
Jan 1 01:12:03 DD-WRT kern.warn kernel: [ 248.000000] ath10k_pci 0000:00:00.0: failed to set vdev 0 tx encap mode: -122
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 248.100000] device wlan1 entered promiscuous mode
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 248.110000] br0: port 4(wlan1) entered forwarding state
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 248.120000] br0: port 4(wlan1) entered forwarding state
Jan 1 01:12:03 DD-WRT kern.alert kernel: [ 248.400000] fast-classifier: shutting down
Jan 1 01:12:03 DD-WRT kern.alert kernel: [ 249.190000] fast-classifier (PBR safe v2.1.6b): starting up
Jan 1 01:12:03 DD-WRT kern.alert kernel: [ 249.200000] fast-classifier: registered
Jan 1 01:12:03 DD-WRT kern.alert kernel: [ 250.370000] fast-classifier: shutting down
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 250.680000] br0: port 3(wlan0) entered forwarding state
Jan 1 01:12:03 DD-WRT kern.alert kernel: [ 251.160000] fast-classifier (PBR safe v2.1.6b): starting up
Jan 1 01:12:03 DD-WRT kern.alert kernel: [ 251.170000] fast-classifier: registered
Jan 1 01:12:03 DD-WRT kern.alert kernel: [ 253.190000] fast-classifier: shutting down
Jan 1 01:12:03 DD-WRT kern.alert kernel: [ 253.300000] fast-classifier (PBR safe v2.1.6b): starting up
Jan 1 01:12:03 DD-WRT kern.alert kernel: [ 253.300000] fast-classifier: registered
Jan 1 01:12:03 DD-WRT kern.alert kernel: [ 253.970000] fast-classifier: shutting down
Jan 1 01:12:03 DD-WRT kern.alert kernel: [ 254.760000] fast-classifier (PBR safe v2.1.6b): starting up
Jan 1 01:12:03 DD-WRT kern.alert kernel: [ 254.770000] fast-classifier: registered
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 263.160000] br0: port 4(wlan1) entered forwarding state
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 509.410000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 5 is up
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 579.140000] device vlan1 left promiscuous mode
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 579.150000] br0: port 1(vlan1) entered disabled state
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 579.160000] device vlan2 left promiscuous mode
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 579.170000] device eth0 left promiscuous mode
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 579.170000] br0: port 2(vlan2) entered disabled state
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 579.180000] device wlan0 left promiscuous mode
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 579.190000] br0: port 3(wlan0) entered disabled state
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 579.210000] device wlan1 left promiscuous mode
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 579.210000] br0: port 4(wlan1) entered disabled state
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 579.510000] ath10k_pci 0000:00:00.0: boot upload otp to 0x1234 len 6209
Jan 1 01:12:03 DD-WRT kern.warn kernel: [ 579.540000] ath10k_pci 0000:00:00.0: otp stream is empty, using board.bin contents
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 580.440000] ath10k_pci 0000:00:00.0: Init Max Stations to 128
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 580.460000] ath10k_pci 0000:00:00.0: P 135 V 16 T 433
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 580.470000] ath10k_pci 0000:00:00.0: alloc rem: 9492 iram: 42308
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 580.480000] ath10k_pci 0000:00:00.0: wmi event ready sw_version 0x41000061 abi_version 1 mac_addr e8:48:b8:c1:a5:1a status 0
Jan 1 01:12:03 DD-WRT kern.warn kernel: [ 580.490000] ath10k_pci 0000:00:00.0: pdev param 0 not supported by firmware
Jan 1 01:12:03 DD-WRT kern.warn kernel: [ 580.510000] ath10k_pci 0000:00:00.0: failed to set vdev 0 tx encap mode: -122
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 580.870000] device br0 entered promiscuous mode
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 580.970000] device vlan1 entered promiscuous mode
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 580.980000] device eth0 entered promiscuous mode
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 580.980000] br0: port 1(vlan1) entered forwarding state
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 580.990000] br0: port 1(vlan1) entered forwarding state
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 581.060000] device vlan2 entered promiscuous mode
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 581.060000] br0: port 2(vlan2) entered forwarding state
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 581.070000] br0: port 2(vlan2) entered forwarding state
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 581.090000] device br0 left promiscuous mode
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 581.100000] device br0 entered promiscuous mode
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 581.120000] device br0 left promiscuous mode
Jan 1 01:12:03 DD-WRT kern.debug kernel: [ 581.250000] ath: EEPROM regdomain: 0x8348
Jan 1 01:12:03 DD-WRT kern.debug kernel: [ 581.250000] ath: EEPROM indicates we should expect a country code
Jan 1 01:12:03 DD-WRT kern.debug kernel: [ 581.250000] ath: doing EEPROM country->regdmn map search
Jan 1 01:12:03 DD-WRT kern.debug kernel: [ 581.250000] ath: country maps to regdmn code: 0x3a
Jan 1 01:12:03 DD-WRT kern.debug kernel: [ 581.250000] ath: Country alpha2 being used: US
Jan 1 01:12:03 DD-WRT kern.debug kernel: [ 581.250000] ath: Regpair used: 0x3a
Jan 1 01:12:03 DD-WRT kern.debug kernel: [ 581.250000] ath: regdomain 0x8348 dynamically updated by user
Jan 1 01:12:03 DD-WRT kern.debug kernel: [ 581.250000] ath: EEPROM regdomain: 0x8348
Jan 1 01:12:03 DD-WRT kern.debug kernel: [ 581.250000] ath: EEPROM indicates we should expect a country code
Jan 1 01:12:03 DD-WRT kern.debug kernel: [ 581.250000] ath: doing EEPROM country->regdmn map search
Jan 1 01:12:03 DD-WRT kern.debug kernel: [ 581.250000] ath: country maps to regdmn code: 0x3a
Jan 1 01:12:03 DD-WRT kern.debug kernel: [ 581.250000] ath: Country alpha2 being used: US
Jan 1 01:12:03 DD-WRT kern.debug kernel: [ 581.250000] ath: Regpair used: 0x3a
Jan 1 01:12:03 DD-WRT kern.debug kernel: [ 581.250000] ath: regdomain 0x8348 dynamically updated by user
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 593.380000] device wlan0 entered promiscuous mode
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 593.380000] br0: port 3(wlan0) entered forwarding state
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 593.390000] br0: port 3(wlan0) entered forwarding state
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 596.000000] br0: port 1(vlan1) entered forwarding state
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 596.080000] br0: port 2(vlan2) entered forwarding state
Jan 1 01:12:03 DD-WRT kern.warn kernel: [ 596.480000] ath10k_pci 0000:00:00.0: wmi command 36870 timeout, restarting hardware
Jan 1 01:12:03 DD-WRT kern.warn kernel: [ 596.480000] ath10k_pci 0000:00:00.0: ani_enable failed from debugfs: -11
Jan 1 01:12:03 DD-WRT kern.warn kernel: [ 596.490000] ath10k_pci 0000:00:00.0: cannot restart a device that hasn't been started
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 596.690000] ath10k_pci 0000:00:00.0: boot upload otp to 0x1234 len 6209
Jan 1 01:12:03 DD-WRT kern.warn kernel: [ 596.720000] ath10k_pci 0000:00:00.0: otp stream is empty, using board.bin contents
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 597.620000] ath10k_pci 0000:00:00.0: Init Max Stations to 128
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 597.630000] ath10k_pci 0000:00:00.0: P 135 V 16 T 433
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 597.640000] ath10k_pci 0000:00:00.0: alloc rem: 9492 iram: 42308
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 597.650000] ath10k_pci 0000:00:00.0: wmi event ready sw_version 0x41000061 abi_version 1 mac_addr e8:48:b8:c1:a5:1a status 0
Jan 1 01:12:03 DD-WRT kern.warn kernel: [ 597.660000] ath10k_pci 0000:00:00.0: pdev param 0 not supported by firmware
Jan 1 01:12:03 DD-WRT kern.warn kernel: [ 597.680000] ath10k_pci 0000:00:00.0: failed to set vdev 0 tx encap mode: -122
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 604.700000] ath10k_pci 0000:00:00.0: boot upload otp to 0x1234 len 6209
Jan 1 01:12:03 DD-WRT kern.warn kernel: [ 604.730000] ath10k_pci 0000:00:00.0: otp stream is empty, using board.bin contents
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 605.610000] ath10k_pci 0000:00:00.0: Init Max Stations to 128
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 605.630000] ath10k_pci 0000:00:00.0: P 135 V 16 T 433
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 605.640000] ath10k_pci 0000:00:00.0: alloc rem: 9492 iram: 42308
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 605.650000] ath10k_pci 0000:00:00.0: wmi event ready sw_version 0x41000061 abi_version 1 mac_addr e8:48:b8:c1:a5:1a status 0
Jan 1 01:12:03 DD-WRT kern.warn kernel: [ 605.660000] ath10k_pci 0000:00:00.0: pdev param 0 not supported by firmware
Jan 1 01:12:03 DD-WRT kern.warn kernel: [ 605.680000] ath10k_pci 0000:00:00.0: failed to set vdev 0 tx encap mode: -122
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 605.740000] device wlan1 entered promiscuous mode
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 605.750000] br0: port 4(wlan1) entered forwarding state
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 605.760000] br0: port 4(wlan1) entered forwarding state
Jan 1 01:12:03 DD-WRT kern.info kernel: [ 608.400000] br0: port 3(wlan0) entered forwarding state
an 1 01:12:03 DD-WRT kern.info kernel: [ 620.800000] br0: port 4(wlan1) entered forwarding state
Jan 1 01:12:03 DD-WRT kern.alert kernel: [ 723.260000] fast-classifier: shutting down
Jan 1 01:12:03 DD-WRT user.info : [sfe] : shortcut forwarding engine successfully stopped
Jan 1 01:12:03 DD-WRT kern.alert kernel: [ 723.370000] fast-classifier (PBR safe v2.1.6b): starting up
Jan 1 01:12:03 DD-WRT kern.alert kernel: [ 723.370000] fast-classifier: registered
Jan 1 01:12:03 DD-WRT user.info : [sfe] : shortcut forwarding engine successfully started
Jan 1 01:12:04 DD-WRT kern.alert kernel: [ 724.090000] fast-classifier: shutting down
Jan 1 01:12:04 DD-WRT user.info : [sfe] : shortcut forwarding engine successfully stopped
Jan 1 01:12:04 DD-WRT kern.alert kernel: [ 724.890000] fast-classifier (PBR safe v2.1.6b): starting up
Jan 1 01:12:04 DD-WRT kern.alert kernel: [ 724.890000] fast-classifier: registered
Jan 1 01:12:04 DD-WRT user.info : [sfe] : shortcut forwarding engine successfully started
Jan 1 01:12:05 DD-WRT user.info : [sfe] : shortcut forwarding engine successfully started
Jan 1 01:12:05 DD-WRT user.info : [telnetd] : daemon successfully stopped
Jan 1 01:12:06 DD-WRT user.info : [dnsmasq] : daemon successfully stopped
Jan 1 01:12:06 DD-WRT user.info : [telnetd] : daemon successfully started
Jan 1 01:12:06 DD-WRT user.info : [pptpd] : daemon successfully stopped
Jan 1 01:12:06 DD-WRT user.info : [hwmon] : successfully started
Jan 1 01:12:06 DD-WRT user.info : [dnsmasq] : daemon successfully started
Jan 1 01:12:06 DD-WRT kern.alert kernel: [ 726.520000] fast-classifier: shutting down
Jan 1 01:12:06 DD-WRT user.info : [sfe] : shortcut forwarding engine successfully stopped
Jan 1 01:12:06 DD-WRT kern.alert kernel: [ 726.640000] fast-classifier (PBR safe v2.1.6b): starting up
Jan 1 01:12:06 DD-WRT kern.alert kernel: [ 726.640000] fast-classifier: registered
Jan 1 01:12:06 DD-WRT user.info : [sfe] : shortcut forwarding engine successfully started
Jan 1 01:12:07 DD-WRT kern.alert kernel: [ 727.340000] fast-classifier: shutting down
Jan 1 01:12:07 DD-WRT user.info : [sfe] : shortcut forwarding engine successfully stopped
Jan 1 01:12:08 DD-WRT kern.alert kernel: [ 728.160000] fast-classifier (PBR safe v2.1.6b): starting up
Jan 1 01:12:08 DD-WRT kern.alert kernel: [ 728.170000] fast-classifier: registered
Jan 1 01:12:08 DD-WRT user.info : [sfe] : shortcut forwarding engine successfully started
Jan 1 01:12:08 DD-WRT user.info : [sfe] : shortcut forwarding engine successfully started
Jan 1 01:12:09 DD-WRT kern.alert kernel: [ 729.280000] fast-classifier: shutting down
Jan 1 01:12:09 DD-WRT user.info : [sfe] : shortcut forwarding engine successfully stopped
Jan 1 01:12:09 DD-WRT kern.alert kernel: [ 729.400000] fast-classifier (PBR safe v2.1.6b): starting up
Jan 1 01:12:09 DD-WRT kern.alert kernel: [ 729.400000] fast-classifier: registered
Jan 1 01:12:09 DD-WRT user.info : [sfe] : shortcut forwarding engine successfully started
Jan 1 01:12:10 DD-WRT kern.alert kernel: [ 730.100000] fast-classifier: shutting down
Jan 1 01:12:10 DD-WRT user.info : [sfe] : shortcut forwarding engine successfully stopped
Jan 1 01:12:10 DD-WRT kern.alert kernel: [ 730.900000] fast-classifier (PBR safe v2.1.6b): starting up
Jan 1 01:12:10 DD-WRT kern.alert kernel: [ 730.910000] fast-classifier: registered
Jan 1 01:12:10 DD-WRT user.info : [sfe] : shortcut forwarding engine successfully started
Jan 1 01:12:11 DD-WRT user.info : [sfe] : shortcut forwarding engine successfully started
Jan 1 01:12:30 DD-WRT daemon.err ntpclient[4703]: Failed resolving address to hostname 2.pool.ntp.org: Try again
Jan 1 01:12:30 DD-WRT daemon.err ntpclient[4703]: Failed resolving server 2.pool.ntp.org: Network is down
Jan 1 01:12:30 DD-WRT daemon.notice ntpclient[4703]: Network up, resolved address to hostname 212.18.3.19
Jan 1 01:12:30 DD-WRT daemon.debug ntpclient[4703]: Connecting to 212.18.3.19 [212.18.3.19] ...
Jan 1 01:12:33 DD-WRT kern.info kernel: [ 753.790000] usbcore: registered new interface driver usbfs
Jan 1 01:12:33 DD-WRT kern.info kernel: [ 753.800000] usbcore: registered new interface driver hub
Jan 1 01:12:33 DD-WRT kern.info kernel: [ 753.800000] usbcore: registered new device driver usb
Jan 1 01:12:33 DD-WRT daemon.debug ntpclient[4703]: Timed out waiting for 212.18.3.19 [212.18.3.19].
Jan 1 01:12:33 DD-WRT daemon.debug ntpclient[4703]: Connecting to 88.99.174.22 [88.99.174.22] ...
Jan 1 01:12:33 DD-WRT kern.info kernel: [ 753.920000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Jan 1 01:12:33 DD-WRT kern.info kernel: [ 753.940000] ehci-platform: EHCI generic platform driver
Jan 1 01:12:33 DD-WRT kern.info kernel: [ 753.950000] ehci-platform ehci-platform.0: EHCI Host Controller
Jan 1 01:12:33 DD-WRT kern.info kernel: [ 753.960000] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
Jan 1 01:12:33 DD-WRT kern.emerg kernel: [ 753.960000] forced host mode, usbmode: 00000013
Jan 1 01:12:33 DD-WRT kern.emerg kernel: [ 753.970000] 16-bit UTMI interface enabled, status: 1c000000
Jan 1 01:12:33 DD-WRT kern.info kernel: [ 753.980000] ehci-platform ehci-platform.0: irq 80, io mem 0x1b000000
Jan 1 01:12:34 DD-WRT kern.info kernel: [ 754.000000] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
Jan 1 01:12:34 DD-WRT kern.info kernel: [ 754.000000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
Jan 1 01:12:34 DD-WRT kern.info kernel: [ 754.010000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Jan 1 01:12:34 DD-WRT kern.info kernel: [ 754.020000] usb usb1: Product: EHCI Host Controller
Jan 1 01:12:34 DD-WRT kern.info kernel: [ 754.020000] usb usb1: Manufacturer: Linux 3.18.140-d6 ehci_hcd
Jan 1 01:12:34 DD-WRT kern.info kernel: [ 754.030000] usb usb1: SerialNumber: ehci-platform.0
Jan 1 01:12:34 DD-WRT kern.info kernel: [ 754.040000] hub 1-0:1.0: USB hub found
Jan 1 01:12:34 DD-WRT kern.info kernel: [ 754.040000] hub 1-0:1.0: 1 port detected
Jan 1 01:12:34 DD-WRT kern.info kernel: [ 754.050000] ehci-platform ehci-platform.1: EHCI Host Controller
Jan 1 01:12:34 DD-WRT kern.info kernel: [ 754.050000] ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 2
Jan 1 01:12:34 DD-WRT kern.emerg kernel: [ 754.060000] forced host mode, usbmode: 00000013
Jan 1 01:12:34 DD-WRT kern.emerg kernel: [ 754.070000] 16-bit UTMI interface enabled, status: 1c000000
Jan 1 01:12:34 DD-WRT kern.info kernel: [ 754.070000] ehci-platform ehci-platform.1: irq 81, io mem 0x1b400000
Jan 1 01:12:34 DD-WRT kern.info kernel: [ 754.100000] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 1.00
Jan 1 01:12:34 DD-WRT kern.info kernel: [ 754.100000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
Jan 1 01:12:34 DD-WRT kern.info kernel: [ 754.110000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Jan 1 01:12:34 DD-WRT kern.info kernel: [ 754.120000] usb usb2: Product: EHCI Host Controller
Jan 1 01:12:34 DD-WRT kern.info kernel: [ 754.120000] usb usb2: Manufacturer: Linux 3.18.140-d6 ehci_hcd
Jan 1 01:12:34 DD-WRT kern.info kernel: [ 754.130000] usb usb2: SerialNumber: ehci-platform.1
Jan 1 01:12:34 DD-WRT kern.info kernel: [ 754.140000] hub 2-0:1.0: USB hub found
Jan 1 01:12:34 DD-WRT kern.info kernel: [ 754.140000] hub 2-0:1.0: 1 port detected
Jan 1 01:12:34 DD-WRT kern.notice kernel: [ 754.750000] SCSI subsystem initialized
Jan 1 01:12:35 DD-WRT kern.info kernel: [ 755.030000] usbcore: registered new interface driver usb-storage
Jan 1 01:12:35 DD-WRT kern.info kernel: [ 755.420000] usbcore: registered new interface driver usblp
Jan 1 01:12:36 DD-WRT daemon.debug ntpclient[4703]: Timed out waiting for 88.99.174.22 [88.99.174.22].
Jan 1 01:12:36 DD-WRT daemon.err process_monitor[2273]: cyclic NTP Update failed (servers 2.pool.ntp.org 212.18.3.19 88.99.174.22)
Jan 1 01:13:08 DD-WRT user.info : [servicemanager] : waiting for services to finish (4)...
Jan 1 01:13:10 DD-WRT user.info : [proftpd] : server successfully started
Jan 1 01:13:11 DD-WRT user.info : [minidlna] : DLNA Media Server successfully started
Jan 1 01:13:11 DD-WRT kern.alert kernel: [ 791.870000] fast-classifier: shutting down
Jan 1 01:13:11 DD-WRT user.info : [sfe] : shortcut forwarding engine successfully stopped
Jan 1 01:13:12 DD-WRT daemon.err ntpclient[4906]: Failed resolving address to hostname 2.pool.ntp.org: Try again
Jan 1 01:13:12 DD-WRT daemon.err ntpclient[4906]: Failed resolving server 2.pool.ntp.org: Network is down
Jan 1 01:13:12 DD-WRT daemon.notice ntpclient[4906]: Network up, resolved address to hostname 212.18.3.19
Jan 1 01:13:12 DD-WRT daemon.debug ntpclient[4906]: Connecting to 212.18.3.19 [212.18.3.19] ...
Jan 1 01:13:12 DD-WRT kern.alert kernel: [ 792.650000] fast-classifier (PBR safe v2.1.6b): starting up
Jan 1 01:13:12 DD-WRT kern.alert kernel: [ 792.660000] fast-classifier: registered
Jan 1 01:13:12 DD-WRT user.info : [sfe] : shortcut forwarding engine successfully started
Jan 1 01:13:14 DD-WRT kern.info kernel: [ 794.050000] Linux kernel CIFS/SMB SERVER 3.4.4 by Namjae Jeon
Jan 1 01:13:14 DD-WRT user.info wsdd2[5221]: starting.
Jan 1 01:13:14 DD-WRT user.info : [smbd] : samba started
Jan 1 01:13:14 DD-WRT local5.err ksmbd: [ksmbd-manager/5225]: ERROR: Can't open `/tmp/ksmbd.subauth': No such file or directory
Jan 1 01:13:14 DD-WRT local5.info ksmbd: [ksmbd-worker/5226]: INFO: User already exists nobody
Jan 1 01:13:14 DD-WRT kern.alert kernel: [ 794.370000] fast-classifier: shutting down
Jan 1 01:13:14 DD-WRT user.info : [sfe] : shortcut forwarding engine successfully stopped
Jan 1 01:13:15 DD-WRT kern.alert kernel: [ 795.190000] fast-classifier (PBR safe v2.1.6b): starting up
Jan 1 01:13:15 DD-WRT kern.alert kernel: [ 795.190000] fast-classifier: registered
Jan 1 01:13:15 DD-WRT user.info : [sfe] : shortcut forwarding engine successfully started
Jan 1 01:13:15 DD-WRT daemon.debug ntpclient[4906]: Timed out waiting for 212.18.3.19 [212.18.3.19].
Jan 1 01:13:15 DD-WRT daemon.debug ntpclient[4906]: Connecting to 88.99.174.22 [88.99.174.22] ...
Jan 1 01:13:16 DD-WRT user.info : [sfe] : shortcut forwarding engine successfully started
Jan 1 01:13:18 DD-WRT daemon.debug ntpclient[4906]: Timed out waiting for 88.99.174.22 [88.99.174.22].
Jan 1 01:13:18 DD-WRT daemon.err process_monitor[2273]: cyclic NTP Update failed (servers 2.pool.ntp.org 212.18.3.19 88.99.174.22)
Jan 1 01:13:53 DD-WRT daemon.err ntpclient[5557]: Failed resolving address to hostname 2.pool.ntp.org: Try again
Jan 1 01:13:53 DD-WRT daemon.err ntpclient[5557]: Failed resolving server 2.pool.ntp.org: Network is down
Jan 1 01:13:53 DD-WRT daemon.notice ntpclient[5557]: Network up, resolved address to hostname 212.18.3.19
Jan 1 01:13:53 DD-WRT daemon.debug ntpclient[5557]: Connecting to 212.18.3.19 [212.18.3.19] ...
Jan 1 01:13:56 DD-WRT daemon.debug ntpclient[5557]: Timed out waiting for 212.18.3.19 [212.18.3.19].
Jan 1 01:13:56 DD-WRT daemon.debug ntpclient[5557]: Connecting to 88.99.174.22 [88.99.174.22] ...
Jan 1 01:13:59 DD-WRT daemon.debug ntpclient[5557]: Timed out waiting for 88.99.174.22 [88.99.174.22].
Jan 1 01:13:59 DD-WRT daemon.err process_monitor[2273]: cyclic NTP Update failed (servers 2.pool.ntp.org 212.18.3.19 88.99.174.22)
Jan 1 01:14:17 DD-WRT user.info : [bridge] : interface vlan1 successfully deleted from bridge br0
Jan 1 01:14:17 DD-WRT kern.info kernel: [ 857.220000] device vlan1 left promiscuous mode
Jan 1 01:14:17 DD-WRT kern.info kernel: [ 857.230000] br0: port 1(vlan1) entered disabled state
Jan 1 01:14:17 DD-WRT user.info : [bridge] : interface vlan2 successfully deleted from bridge br0
Jan 1 01:14:17 DD-WRT kern.info kernel: [ 857.240000] device vlan2 left promiscuous mode
Jan 1 01:14:17 DD-WRT kern.info kernel: [ 857.250000] device eth0 left promiscuous mode
Jan 1 01:14:17 DD-WRT kern.info kernel: [ 857.250000] br0: port 2(vlan2) entered disabled state
Jan 1 01:14:17 DD-WRT user.info : [bridge] : interface wlan0 successfully deleted from bridge br0
Jan 1 01:14:17 DD-WRT kern.info kernel: [ 857.270000] device wlan0 left promiscuous mode
Jan 1 01:14:17 DD-WRT kern.info kernel: [ 857.270000] br0: port 3(wlan0) entered disabled state
Jan 1 01:14:17 DD-WRT user.info : [bridge] : interface wlan1 successfully deleted from bridge br0
Jan 1 01:14:17 DD-WRT kern.info kernel: [ 857.280000] device wlan1 left promiscuous mode
Jan 1 01:14:17 DD-WRT kern.info kernel: [ 857.290000] br0: port 4(wlan1) entered disabled state
Jan 1 01:14:17 DD-WRT user.info : [bridge] : bridge br0 successfully deleted
Jan 1 01:14:17 DD-WRT user.info : [hostapd] : hostapd daemon successfully stopped
Jan 1 01:14:17 DD-WRT kern.info kernel: [ 857.630000] ath10k_pci 0000:00:00.0: boot upload otp to 0x1234 len 6209
Jan 1 01:14:17 DD-WRT kern.warn kernel: [ 857.660000] ath10k_pci 0000:00:00.0: otp stream is empty, using board.bin contents
Jan 1 01:14:18 DD-WRT kern.info kernel: [ 858.560000] ath10k_pci 0000:00:00.0: Init Max Stations to 128
Jan 1 01:14:18 DD-WRT kern.info kernel: [ 858.580000] ath10k_pci 0000:00:00.0: P 135 V 16 T 433
Jan 1 01:14:18 DD-WRT kern.info kernel: [ 858.590000] ath10k_pci 0000:00:00.0: alloc rem: 9492 iram: 42308
Jan 1 01:14:18 DD-WRT kern.info kernel: [ 858.590000] ath10k_pci 0000:00:00.0: wmi event ready sw_version 0x41000061 abi_version 1 mac_addr e8:48:b8:c1:a5:1a status 0
Jan 1 01:14:18 DD-WRT kern.warn kernel: [ 858.610000] ath10k_pci 0000:00:00.0: pdev param 0 not supported by firmware
Jan 1 01:14:18 DD-WRT kern.warn kernel: [ 858.630000] ath10k_pci 0000:00:00.0: failed to set vdev 0 tx encap mode: -122
Jan 1 01:14:18 DD-WRT user.debug : mac80211: start deconfigure_single_ath9k
Jan 1 01:14:18 DD-WRT user.debug : mac80211: start delete_ath9k_devices
Jan 1 01:14:18 DD-WRT user.info : [bridge] : interface wlan0 successfully deleted from bridge br0
Jan 1 01:14:18 DD-WRT user.debug : mac80211: leave delete_ath9k_devices
Jan 1 01:14:18 DD-WRT user.debug : mac80211: leave deconfigure_single_ath9k
Jan 1 01:14:18 DD-WRT user.debug : mac80211: start deconfigure_single_ath9k
Jan 1 01:14:18 DD-WRT user.debug : mac80211: start delete_ath9k_devices
Jan 1 01:14:18 DD-WRT user.info : [bridge] : interface wlan1 successfully deleted from bridge br0
Jan 1 01:14:18 DD-WRT user.debug : mac80211: leave delete_ath9k_devices
Jan 1 01:14:18 DD-WRT user.debug : mac80211: leave deconfigure_single_ath9k
Jan 1 01:14:19 DD-WRT user.info : [bridge] : bridge br0 successfully added
Jan 1 01:14:19 DD-WRT kern.info kernel: [ 859.050000] device br0 entered promiscuous mode
Jan 1 01:14:19 DD-WRT user.info : [bridge] : interface vlan1 successfully added to bridge br0
Jan 1 01:14:19 DD-WRT kern.info kernel: [ 859.150000] device vlan1 entered promiscuous mode
Jan 1 01:14:19 DD-WRT kern.info kernel: [ 859.150000] device eth0 entered promiscuous mode
Jan 1 01:14:19 DD-WRT kern.info kernel: [ 859.160000] br0: port 1(vlan1) entered forwarding state
Jan 1 01:14:19 DD-WRT kern.info kernel: [ 859.170000] br0: port 1(vlan1) entered forwarding state
Jan 1 01:14:19 DD-WRT user.info : [bridge] : interface vlan2 successfully added to bridge br0
Jan 1 01:14:19 DD-WRT kern.info kernel: [ 859.250000] device vlan2 entered promiscuous mode
Jan 1 01:14:19 DD-WRT kern.info kernel: [ 859.260000] br0: port 2(vlan2) entered forwarding state
Jan 1 01:14:19 DD-WRT kern.info kernel: [ 859.260000] br0: port 2(vlan2) entered forwarding state
Jan 1 01:14:19 DD-WRT kern.info kernel: [ 859.280000] device br0 left promiscuous mode
Jan 1 01:14:19 DD-WRT kern.info kernel: [ 859.290000] device br0 entered promiscuous mode
Jan 1 01:14:19 DD-WRT kern.info kernel: [ 859.310000] device br0 left promiscuous mode
Jan 1 01:14:19 DD-WRT user.debug : mac80211: start deconfigure_single_ath9k
Jan 1 01:14:19 DD-WRT user.debug : mac80211: start delete_ath9k_devices
Jan 1 01:14:19 DD-WRT user.debug : mac80211: leave delete_ath9k_devices
Jan 1 01:14:19 DD-WRT user.debug : mac80211: leave deconfigure_single_ath9k
Jan 1 01:14:19 DD-WRT user.debug : mac80211: start deconfigure_single_ath9k
Jan 1 01:14:19 DD-WRT user.debug : mac80211: start delete_ath9k_devices
Jan 1 01:14:19 DD-WRT user.debug : mac80211: leave delete_ath9k_devices
Jan 1 01:14:19 DD-WRT user.debug : mac80211: leave deconfigure_single_ath9k
Jan 1 01:14:19 DD-WRT kern.debug kernel: [ 859.450000] ath: EEPROM regdomain: 0x8348
Jan 1 01:14:19 DD-WRT kern.debug kernel: [ 859.450000] ath: EEPROM indicates we should expect a country code
Jan 1 01:14:19 DD-WRT kern.debug kernel: [ 859.450000] ath: doing EEPROM country->regdmn map search
Jan 1 01:14:19 DD-WRT kern.debug kernel: [ 859.450000] ath: country maps to regdmn code: 0x3a
Jan 1 01:14:19 DD-WRT kern.debug kernel: [ 859.450000] ath: Country alpha2 being used: US
Jan 1 01:14:19 DD-WRT kern.debug kernel: [ 859.450000] ath: Regpair used: 0x3a
Jan 1 01:14:19 DD-WRT kern.debug kernel: [ 859.450000] ath: regdomain 0x8348 dynamically updated by user
Jan 1 01:14:19 DD-WRT kern.debug kernel: [ 859.450000] ath: EEPROM regdomain: 0x8348
Jan 1 01:14:19 DD-WRT kern.debug kernel: [ 859.450000] ath: EEPROM indicates we should expect a country code
Jan 1 01:14:19 DD-WRT kern.debug kernel: [ 859.450000] ath: doing EEPROM country->regdmn map search
Jan 1 01:14:19 DD-WRT kern.debug kernel: [ 859.450000] ath: country maps to regdmn code: 0x3a
Jan 1 01:14:19 DD-WRT kern.debug kernel: [ 859.450000] ath: Country alpha2 being used: US
Jan 1 01:14:19 DD-WRT kern.debug kernel: [ 859.450000] ath: Regpair used: 0x3a
Jan 1 01:14:19 DD-WRT kern.debug kernel: [ 859.450000] ath: regdomain 0x8348 dynamically updated by user
Jan 1 01:14:19 DD-WRT user.debug : mac80211: start configure_single_ath9k
Jan 1 01:14:19 DD-WRT user.debug : mac80211: start setRTS
Jan 1 01:14:19 DD-WRT user.debug : mac80211: leave setRTS
Jan 1 01:14:31 DD-WRT user.info : [autochannel] : wlan0: freq:2452 qual:85 noise:-93 eirp: 24
Jan 1 01:14:31 DD-WRT user.info : [autochannel] : wlan0: freq:2432 qual:79 noise:-95 eirp: 24
Jan 1 01:14:31 DD-WRT user.info : [autochannel] : wlan0: freq:2442 qual:68 noise:-94 eirp: 24
Jan 1 01:14:31 DD-WRT user.info : [autochannel] : wlan0: freq:2462 qual:62 noise:-95 eirp: 24
Jan 1 01:14:31 DD-WRT user.info : [autochannel] : wlan0: freq:2412 qual:46 noise:-95 eirp: 24
Jan 1 01:14:31 DD-WRT user.info : [autochannel] : wlan0: freq:2447 qual:41 noise:-94 eirp: 24
Jan 1 01:14:31 DD-WRT user.info : [autochannel] : wlan0: freq:2437 qual:38 noise:-95 eirp: 24
Jan 1 01:14:31 DD-WRT user.info : [autochannel] : wlan0: freq:2457 qual:36 noise:-95 eirp: 24
Jan 1 01:14:31 DD-WRT user.info : [autochannel] : wlan0: freq:2422 qual:29 noise:-95 eirp: 24
Jan 1 01:14:31 DD-WRT user.info : [autochannel] : wlan0: freq:2417 qual:23 noise:-95 eirp: 24
Jan 1 01:14:31 DD-WRT user.info : [autochannel] : wlan0: freq:2427 qual:19 noise:-95 eirp: 24
Jan 1 01:17:43 DD-WRT user.debug : mac80211: leave setMacFilter
Jan 1 01:17:44 DD-WRT kern.info kernel: [ 1064.260000] ath10k_pci 0000:00:00.0: boot upload otp to 0x1234 len 6209
Jan 1 01:17:44 DD-WRT kern.warn kernel: [ 1064.290000] ath10k_pci 0000:00:00.0: otp stream is empty, using board.bin contents
Jan 1 01:17:45 DD-WRT kern.info kernel: [ 1065.390000] ath10k_pci 0000:00:00.0: Init Max Stations to 128
Jan 1 01:17:45 DD-WRT kern.info kernel: [ 1065.410000] ath10k_pci 0000:00:00.0: P 135 V 16 T 433
Jan 1 01:17:45 DD-WRT kern.info kernel: [ 1065.420000] ath10k_pci 0000:00:00.0: alloc rem: 9492 iram: 42308
Jan 1 01:17:45 DD-WRT kern.info kernel: [ 1065.420000] ath10k_pci 0000:00:00.0: wmi event ready sw_version 0x41000061 abi_version 1 mac_addr e8:48:b8:c1:a5:1a status 0
Jan 1 01:17:45 DD-WRT kern.warn kernel: [ 1065.440000] ath10k_pci 0000:00:00.0: pdev param 0 not supported by firmware
Jan 1 01:17:45 DD-WRT kern.warn kernel: [ 1065.460000] ath10k_pci 0000:00:00.0: failed to set vdev 0 tx encap mode: -122
Jan 1 01:17:45 DD-WRT kern.info kernel: [ 1065.480000] device wlan1 entered promiscuous mode
Jan 1 01:17:45 DD-WRT kern.info kernel: [ 1065.610000] br0: port 4(wlan1) entered forwarding state
Jan 1 01:17:45 DD-WRT kern.info kernel: [ 1065.620000] br0: port 4(wlan1) entered forwarding state
Jan 1 01:17:45 DD-WRT user.info : [bridge] : interface wlan1 successfully added to bridge br0
Jan 1 01:17:46 DD-WRT user.info : [dnsmasq] : daemon successfully stopped
Jan 1 01:17:46 DD-WRT user.info : [wsdd2] : windows service discovery daemon successfully stopped
Jan 1 01:17:46 DD-WRT user.debug wsdd2[5938]: 'Terminated' signal received.
Jan 1 01:17:46 DD-WRT user.info wsdd2[5938]: terminating.
Jan 1 01:17:46 DD-WRT user.info : [ksmbd.mountd] : samba daemon successfully stopped
Jan 1 01:17:46 DD-WRT local5.info ksmbd: [ksmbd-worker/5942]: INFO: Child received signal: 15 (Terminated)
Jan 1 01:17:46 DD-WRT local5.err ksmbd: [ksmbd-manager/5941]: ERROR: WARNING: child process exited abnormally: 5942
Jan 1 01:17:46 DD-WRT local5.err ksmbd: [ksmbd-manager/5941]: ERROR: can't execute kill 5942: No such process
Jan 1 01:17:46 DD-WRT local5.info ksmbd: [ksmbd-manager/5941]: INFO: Exiting. Bye!
Jan 1 01:17:46 DD-WRT kern.info kernel: [ 1066.210000] ksmbd: kill command received
Jan 1 01:17:46 DD-WRT user.info : [dnsmasq] : daemon successfully started
Jan 1 01:17:47 DD-WRT kern.info kernel: [ 1067.220000] Linux kernel CIFS/SMB SERVER 3.4.4 by Namjae Jeon
Jan 1 01:17:47 DD-WRT user.info wsdd2[6943]: starting.
Jan 1 01:17:47 DD-WRT user.info : [smbd] : samba started
Jan 1 01:17:47 DD-WRT local5.info ksmbd: [ksmbd-worker/6947]: INFO: User already exists nobody
Jan 1 01:17:47 DD-WRT kern.info kernel: [ 1067.680000] br0: port 3(wlan0) entered forwarding state
Jan 1 01:17:50 DD-WRT user.info : [httpd] : daemon successfully stopped
Jan 1 01:17:50 DD-WRT daemon.info httpd[3160]: [httpd] : httpd server shutdown
Jan 1 01:17:50 DD-WRT daemon.info httpd[6991]: [httpd] : httpd server started at port 80
Jan 1 01:17:50 DD-WRT user.info : [httpd] : http daemon successfully started
Jan 1 01:18:00 DD-WRT daemon.err ntpclient[7016]: Failed resolving address to hostname 2.pool.ntp.org: Try again
Jan 1 01:18:00 DD-WRT daemon.err ntpclient[7016]: Failed resolving server 2.pool.ntp.org: Network is down
Jan 1 01:18:00 DD-WRT daemon.notice ntpclient[7016]: Network up, resolved address to hostname 212.18.3.19
Jan 1 01:18:00 DD-WRT daemon.debug ntpclient[7016]: Connecting to 212.18.3.19 [212.18.3.19] ...
Jan 1 01:18:00 DD-WRT kern.info kernel: [ 1080.640000] br0: port 4(wlan1) entered forwarding state
Jan 1 01:18:03 DD-WRT daemon.debug ntpclient[7016]: Timed out waiting for 212.18.3.19 [212.18.3.19].
Jan 1 01:18:03 DD-WRT daemon.debug ntpclient[7016]: Connecting to 88.99.174.22 [88.99.174.22] ...
Jan 1 01:18:06 DD-WRT daemon.debug ntpclient[7016]: Timed out waiting for 88.99.174.22 [88.99.174.22].
Jan 1 01:18:06 DD-WRT daemon.err process_monitor[2273]: cyclic NTP Update failed (servers 2.pool.ntp.org 212.18.3.19 88.99.174.22)
Jan 1 01:18:41 DD-WRT daemon.err ntpclient[7071]: Failed resolving address to hostname 2.pool.ntp.org: Try again
Jan 1 01:18:41 DD-WRT daemon.err ntpclient[7071]: Failed resolving server 2.pool.ntp.org: Network is down
Jan 1 01:18:41 DD-WRT daemon.notice ntpclient[7071]: Network up, resolved address to hostname 212.18.3.19
Jan 1 01:18:41 DD-WRT daemon.debug ntpclient[7071]: Connecting to 212.18.3.19 [212.18.3.19] ...
Jan 1 01:18:44 DD-WRT daemon.debug ntpclient[7071]: Timed out waiting for 212.18.3.19 [212.18.3.19].
Jan 1 01:18:44 DD-WRT daemon.debug ntpclient[7071]: Connecting to 88.99.174.22 [88.99.174.22] ...
Jan 1 01:18:47 DD-WRT daemon.debug ntpclient[7071]: Timed out waiting for 88.99.174.22 [88.99.174.22].
Jan 1 01:18:47 DD-WRT daemon.err process_monitor[2273]: cyclic NTP Update failed (servers 2.pool.ntp.org 212.18.3.19 88.99.174.22)
Jan 1 01:19:22 DD-WRT daemon.err ntpclient[7160]: Failed resolving address to hostname 2.pool.ntp.org: Try again
Jan 1 01:19:22 DD-WRT daemon.err ntpclient[7160]: Failed resolving server 2.pool.ntp.org: Network is down
Jan 1 01:19:22 DD-WRT daemon.notice ntpclient[7160]: Network up, resolved address to hostname 212.18.3.19
Jan 1 01:19:22 DD-WRT daemon.debug ntpclient[7160]: Connecting to 212.18.3.19 [212.18.3.19] ...
Jan 1 01:19:25 DD-WRT daemon.debug ntpclient[7160]: Timed out waiting for 212.18.3.19 [212.18.3.19].
Jan 1 01:19:25 DD-WRT daemon.debug ntpclient[7160]: Connecting to 88.99.174.22 [88.99.174.22] ...
Jan 1 01:19:28 DD-WRT daemon.debug ntpclient[7160]: Timed out waiting for 88.99.174.22 [88.99.174.22].
Jan 1 01:19:28 DD-WRT daemon.err process_monitor[2273]: cyclic NTP Update failed (servers 2.pool.ntp.org 212.18.3.19 88.99.174.22)
Jan 1 01:20:03 DD-WRT daemon.err ntpclient[7177]: Failed resolving address to hostname 2.pool.ntp.org: Try again
Jan 1 01:20:03 DD-WRT daemon.err ntpclient[7177]: Failed resolving server 2.pool.ntp.org: Network is down
Jan 1 01:20:03 DD-WRT daemon.notice ntpclient[7177]: Network up, resolved address to hostname 212.18.3.19
Jan 1 01:20:03 DD-WRT daemon.debug ntpclient[7177]: Connecting to 212.18.3.19 [212.18.3.19] ...
Jan 1 01:20:06 DD-WRT daemon.debug ntpclient[7177]: Timed out waiting for 212.18.3.19 [212.18.3.19].
Jan 1 01:20:06 DD-WRT daemon.debug ntpclient[7177]: Connecting to 88.99.174.22 [88.99.174.22] ...
Jan 1 01:20:09 DD-WRT daemon.debug ntpclient[7177]: Timed out waiting for 88.99.174.22 [88.99.174.22].
Jan 1 01:20:09 DD-WRT daemon.err process_monitor[2273]: cyclic NTP Update failed (servers 2.pool.ntp.org 212.18.3.19 88.99.174.22)
Jan 1 01:20:44 DD-WRT daemon.err ntpclient[7201]: Failed resolving address to hostname 2.pool.ntp.org: Try again
Jan 1 01:20:44 DD-WRT daemon.err ntpclient[7201]: Failed resolving server 2.pool.ntp.org: Network is down
Jan 1 01:20:44 DD-WRT daemon.notice ntpclient[7201]: Network up, resolved address to hostname 212.18.3.19
Jan 1 01:20:44 DD-WRT daemon.debug ntpclient[7201]: Connecting to 212.18.3.19 [212.18.3.19] ...
Jan 1 01:20:47 DD-WRT daemon.debug ntpclient[7201]: Timed out waiting for 212.18.3.19 [212.18.3.19].
Jan 1 01:20:47 DD-WRT daemon.debug ntpclient[7201]: Connecting to 88.99.174.22 [88.99.174.22] ...
Jan 1 01:20:50 DD-WRT daemon.debug ntpclient[7201]: Timed out waiting for 88.99.174.22 [88.99.174.22].
Jan 1 01:20:50 DD-WRT daemon.err process_monitor[2273]: cyclic NTP Update failed (servers 2.pool.ntp.org 212.18.3.19 88.99.174.22)
Jan 1 01:21:25 DD-WRT daemon.err ntpclient[7217]: Failed resolving address to hostname 2.pool.ntp.org: Try again
Jan 1 01:21:25 DD-WRT daemon.err ntpclient[7217]: Failed resolving server 2.pool.ntp.org: Network is down
Jan 1 01:21:25 DD-WRT daemon.notice ntpclient[7217]: Network up, resolved address to hostname 212.18.3.19
Jan 1 01:21:25 DD-WRT daemon.debug ntpclient[7217]: Connecting to 212.18.3.19 [212.18.3.19] ...
Jan 1 01:21:28 DD-WRT daemon.debug ntpclient[7217]: Timed out waiting for 212.18.3.19 [212.18.3.19].
Jan 1 01:21:28 DD-WRT daemon.debug ntpclient[7217]: Connecting to 88.99.174.22 [88.99.174.22] ...
Jan 1 01:21:31 DD-WRT daemon.debug ntpclient[7217]: Timed out waiting for 88.99.174.22 [88.99.174.22].
Jan 1 01:21:31 DD-WRT daemon.err process_monitor[2273]: cyclic NTP Update failed (servers 2.pool.ntp.org 212.18.3.19 88.99.174.22)
Jan 1 01:22:06 DD-WRT daemon.err ntpclient[7302]: Failed resolving address to hostname 2.pool.ntp.org: Try again
Jan 1 01:22:06 DD-WRT daemon.err ntpclient[7302]: Failed resolving server 2.pool.ntp.org: Network is down
Jan 1 01:22:06 DD-WRT daemon.notice ntpclient[7302]: Network up, resolved address to hostname 212.18.3.19
Jan 1 01:22:06 DD-WRT daemon.debug ntpclient[7302]: Connecting to 212.18.3.19 [212.18.3.19] ...
Jan 1 01:22:09 DD-WRT daemon.debug ntpclient[7302]: Timed out waiting for 212.18.3.19 [212.18.3.19].
Jan 1 01:22:09 DD-WRT daemon.debug ntpclient[7302]: Connecting to 88.99.174.22 [88.99.174.22] ...
Jan 1 01:22:12 DD-WRT daemon.debug ntpclient[7302]: Timed out waiting for 88.99.174.22 [88.99.174.22].
Jan 1 01:22:12 DD-WRT daemon.err process_monitor[2273]: cyclic NTP Update failed (servers 2.pool.ntp.org 212.18.3.19 88.99.174.22)
Jan 1 01:22:47 DD-WRT daemon.err ntpclient[7337]: Failed resolving address to hostname 2.pool.ntp.org: Try again
Jan 1 01:22:47 DD-WRT daemon.err ntpclient[7337]: Failed resolving server 2.pool.ntp.org: Network is down
Jan 1 01:22:47 DD-WRT daemon.notice ntpclient[7337]: Network up, resolved address to hostname 212.18.3.19
Jan 1 01:22:47 DD-WRT daemon.debug ntpclient[7337]: Connecting to 212.18.3.19 [212.18.3.19] ...
Jan 1 01:22:50 DD-WRT daemon.debug ntpclient[7337]: Timed out waiting for 212.18.3.19 [212.18.3.19].
Jan 1 01:22:50 DD-WRT daemon.debug ntpclient[7337]: Connecting to 88.99.174.22 [88.99.174.22] ...
Jan 1 01:22:53 DD-WRT daemon.debug ntpclient[7337]: Timed out waiting for 88.99.174.22 [88.99.174.22].
Jan 1 01:22:53 DD-WRT daemon.err process_monitor[2273]: cyclic NTP Update failed (servers 2.pool.ntp.org 212.18.3.19 88.99.174.22)
Jan 1 01:23:28 DD-WRT daemon.err ntpclient[7516]: Failed resolving address to hostname 2.pool.ntp.org: Try again
Jan 1 01:23:28 DD-WRT daemon.err ntpclient[7516]: Failed resolving server 2.pool.ntp.org: Network is down
Jan 1 01:23:28 DD-WRT daemon.notice ntpclient[7516]: Network up, resolved address to hostname 212.18.3.19
Jan 1 01:23:28 DD-WRT daemon.debug ntpclient[7516]: Connecting to 212.18.3.19 [212.18.3.19] ...
Jan 1 01:23:31 DD-WRT daemon.debug ntpclient[7516]: Timed out waiting for 212.18.3.19 [212.18.3.19].
Jan 1 01:23:31 DD-WRT daemon.debug ntpclient[7516]: Connecting to 88.99.174.22 [88.99.174.22] ...
Jan 1 01:23:34 DD-WRT daemon.debug ntpclient[7516]: Timed out waiting for 88.99.174.22 [88.99.174.22].
Jan 1 01:23:34 DD-WRT daemon.err process_monitor[2273]: cyclic NTP Update failed (servers 2.pool.ntp.org 212.18.3.19 88.99.174.22)
Jan 1 01:24:09 DD-WRT daemon.err ntpclient[7567]: Failed resolving address to hostname 2.pool.ntp.org: Try again
Jan 1 01:24:09 DD-WRT daemon.err ntpclient[7567]: Failed resolving server 2.pool.ntp.org: Network is down
Jan 1 01:24:09 DD-WRT daemon.notice ntpclient[7567]: Network up, resolved address to hostname 212.18.3.19
Jan 1 01:24:09 DD-WRT daemon.debug ntpclient[7567]: Connecting to 212.18.3.19 [212.18.3.19] ...
Jan 1 01:24:12 DD-WRT daemon.debug ntpclient[7567]: Timed out waiting for 212.18.3.19 [212.18.3.19].
Jan 1 01:24:12 DD-WRT daemon.debug ntpclient[7567]: Connecting to 88.99.174.22 [88.99.174.22] ...
Jan 1 01:24:15 DD-WRT daemon.debug ntpclient[7567]: Timed out waiting for 88.99.174.22 [88.99.174.22].
Jan 1 01:24:15 DD-WRT daemon.err process_monitor[2273]: cyclic NTP Update failed (servers 2.pool.ntp.org 212.18.3.19 88.99.174.22)
Jan 1 01:24:50 DD-WRT daemon.err ntpclient[7611]: Failed resolving address to hostname 2.pool.ntp.org: Try again
Jan 1 01:24:50 DD-WRT daemon.err ntpclient[7611]: Failed resolving server 2.pool.ntp.org: Network is down
Jan 1 01:24:50 DD-WRT daemon.notice ntpclient[7611]: Network up, resolved address to hostname 212.18.3.19
Jan 1 01:24:50 DD-WRT daemon.debug ntpclient[7611]: Connecting to 212.18.3.19 [212.18.3.19] ...
Jan 1 01:24:53 DD-WRT daemon.debug ntpclient[7611]: Timed out waiting for 212.18.3.19 [212.18.3.19].
Jan 1 01:24:53 DD-WRT daemon.debug ntpclient[7611]: Connecting to 88.99.174.22 [88.99.174.22] ...
Jan 1 01:24:56 DD-WRT daemon.debug ntpclient[7611]: Timed out waiting for 88.99.174.22 [88.99.174.22].
Jan 1 01:24:56 DD-WRT daemon.err process_monitor[2273]: cyclic NTP Update failed (servers 2.pool.ntp.org 212.18.3.19 88.99.174.22)
Jan 1 01:25:31 DD-WRT daemon.err ntpclient[7664]: Failed resolving address to hostname 2.pool.ntp.org: Try again
Jan 1 01:25:31 DD-WRT daemon.err ntpclient[7664]: Failed resolving server 2.pool.ntp.org: Network is down
Jan 1 01:25:31 DD-WRT daemon.notice ntpclient[7664]: Network up, resolved address to hostname 212.18.3.19
Jan 1 01:25:31 DD-WRT daemon.debug ntpclient[7664]: Connecting to 212.18.3.19 [212.18.3.19] ...
Jan 1 01:25:34 DD-WRT daemon.debug ntpclient[7664]: Timed out waiting for 212.18.3.19 [212.18.3.19].
Jan 1 01:25:34 DD-WRT daemon.debug ntpclient[7664]: Connecting to 88.99.174.22 [88.99.174.22] ...
Jan 1 01:25:37 DD-WRT daemon.debug ntpclient[7664]: Timed out waiting for 88.99.174.22 [88.99.174.22].
Jan 1 01:25:37 DD-WRT daemon.err process_monitor[2273]: cyclic NTP Update failed (servers 2.pool.ntp.org 212.18.3.19 88.99.174.22)
Jan 1 01:26:13 DD-WRT daemon.err ntpclient[7760]: Failed resolving address to hostname 2.pool.ntp.org: Try again
Jan 1 01:26:13 DD-WRT daemon.err ntpclient[7760]: Failed resolving server 2.pool.ntp.org: Network is down
Jan 1 01:26:13 DD-WRT daemon.notice ntpclient[7760]: Network up, resolved address to hostname 212.18.3.19
Jan 1 01:26:13 DD-WRT daemon.debug ntpclient[7760]: Connecting to 212.18.3.19 [212.18.3.19] ...
Jan 1 01:26:16 DD-WRT daemon.debug ntpclient[7760]: Timed out waiting for 212.18.3.19 [212.18.3.19].
Jan 1 01:26:16 DD-WRT daemon.debug ntpclient[7760]: Connecting to 88.99.174.22 [88.99.174.22] ...
Jan 1 01:26:19 DD-WRT daemon.debug ntpclient[7760]: Timed out waiting for 88.99.174.22 [88.99.174.22].
Jan 1 01:26:19 DD-WRT daemon.err process_monitor[2273]: cyclic NTP Update failed (servers 2.pool.ntp.org 212.18.3.19 88.99.174.22)
Jan 1 01:26:54 DD-WRT daemon.err ntpclient[7858]: Failed resolving address to hostname 2.pool.ntp.org: Try again
Jan 1 01:26:54 DD-WRT daemon.err ntpclient[7858]: Failed resolving server 2.pool.ntp.org: Network is down
Jan 1 01:26:54 DD-WRT daemon.notice ntpclient[7858]: Network up, resolved address to hostname 212.18.3.19
Jan 1 01:26:54 DD-WRT daemon.debug ntpclient[7858]: Connecting to 212.18.3.19 [212.18.3.19] ...
Jan 1 01:26:57 DD-WRT daemon.debug ntpclient[7858]: Timed out waiting for 212.18.3.19 [212.18.3.19].
Jan 1 01:26:57 DD-WRT daemon.debug ntpclient[7858]: Connecting to 88.99.174.22 [88.99.174.22] ...
Jan 1 01:27:00 DD-WRT daemon.debug ntpclient[7858]: Timed out waiting for 88.99.174.22 [88.99.174.22].
Jan 1 01:27:00 DD-WRT daemon.err process_monitor[2273]: cyclic NTP Update failed (servers 2.pool.ntp.org 212.18.3.19 88.99.174.22)
If you see my error.....
Can I try to put an old version, but which one to choose?
Thanks again
Joined: 08 May 2018 Posts: 14224 Location: Texas, USA
Posted: Sat May 14, 2022 0:37 Post subject:
Post your wireless settings' screenshots - ensure you tick Advanced settings. First problem is you're using autochannel. Use a wifi analyzer app on your phone and pick a channel. You should also read the included router firmware help links within the firmware itself.
Hello gentlemen.
I tested several things thanks to you.
Actually I fixed the time via Ntp server. tks
I put fixed channels back on Wl0 and Wl1. (I had put auto because it did not work fixed)
I am channel 1 on Archer v2 and channel 5 on Archer V5
I voluntarily put different channels (and which are not occupied by my neighbors)
But you will see this on my settings.
Previously I had this connection:
Provider box <--RJ45-->Archer V2 Lan <--RJ45 --> Archer V5 Lan and it didn't work
now I have put the 2 Archers in parallel
Archer V2 Lan<--Rj45-->Provider Box<--Rj45-->Archer V5 Lan
It seems to work...
I have an Archer on the ground floor and an Archer in the basement to convert into a cinema and sports hall.
I put the same SSIDs back on the WLs in order to make a minimum of cuts when switching with the telephones.
If there are bugs I will change the SSIDs.
Code:
Delete because error
sorry
Do you think my config is correct?
Can we use the Mesh system if I take another Archer C5?
Thanks a lot and good Week-end!!!
Last edited by vwstepha on Sat May 14, 2022 12:51; edited 1 time in total
Joined: 31 Jul 2021 Posts: 2146 Location: All over YOUR webs
Posted: Fri May 20, 2022 12:47 Post subject:
Marked as solved.
In future try to get such verbose log output attached to reply instead of posting inline, otherwise trying to read trough the thread is a nightmare that can possibly put off any people trying to help from actually doing so.