WRT3200ACM wifi "ieee80211 phy1: staid 1 deleted"

Post new topic   Reply to topic    DD-WRT Forum Index -> Marvell MVEBU based Hardware (WRT1900AC etc.)
Author Message
SmithDemocles
DD-WRT Novice


Joined: 19 Dec 2017
Posts: 6

PostPosted: Fri Mar 18, 2022 17:18    Post subject: WRT3200ACM wifi "ieee80211 phy1: staid 1 deleted" Reply with quote
Router Model: Linksys WRT3200ACM
Firmware Version: DD-WRT v3.0-r48494 std (03/15/22)
Kernel Version: Linux 4.9.306 #3135 SMP Tue Mar 15 02:59:36 +07 2022 armv7l
Previous/Reset: Reset
Mode/Status: AP

I used to have installed r48141 (everything worked properly), but decided to update to r48432, but because I messed up with the configuration I had to reset the router.
Since the reset I was not able to have the wifi working with r48432.
Decided to upgrade to r48494 resetting to default settings.

Via Ethernet everything is working as expected.
wifi is giving me issues:
- Devices are not able to connect
- The Channel Width is always 20 no matter the configuration (tried to save and restart the router).

I have tried multiple configurations of Wireless Network Mode and/or Channel Width.
I have tried assigning a specific channel or leaving it set to auto.

The router has 3 physical interfaces, I have always left the third WLAN (wlan2) disable (if I remember properly it was used for DFS Radar Detection).
I tried to set wlan0 and wlan1 together and independently with all sorts of issues...
NO IDEA Sad

I decided to take it slowly.

What I have found out so far:
If I start only the wifi without any security, my devices can log in (tried a Nexus 6 and laptop with linux), but as soon as I choose WPA authentication (no matter which configuration) I am not able to connect.


Current setup:
Wireless Basic Settings:



Wireless Security:



Wireless Status:




Something interesting:
When I try to connect the following message is displayed in the message buffer of the kernel (dmesg):
Code:
ieee80211 phy1: staid 1 deleted


By Google it I have found the following but not much more...


As additional information:
Code:
root@DD-WRT:~# cat /sys/kernel/debug/ieee80211/phy0/mwlwifi/info

driver name: mwlwifi
chip type: 88W8964
hw version: 7
driver version: 10.3.8.0-20181120
firmware version: 0x0903020c
power table loaded from dts: no
firmware region code: 0x30
mac address: 60:38:e0:c7:77:92
2g: disable
5g: enable
antenna: 4 4
irq number: 46
ap macid support: 0000ffff
sta macid support: 00010000
macid used: 00000000
radio: disable
iobase0: e0c80000
iobase1: e0f00000
tx limit: 1024
rx limit: 16384





I am not really sure what to do, any ideas or suggestions are welcome!

Thank you
Sponsor
egc
DD-WRT Guru


Joined: 18 Mar 2014
Posts: 12839
Location: Netherlands

PostPosted: Fri Mar 18, 2022 17:39    Post subject: Reply with quote
Do not use Autochannel

Do use WPA2 Personal with CCMP-128 (AES), you forgot to enable this last one

_________________
Routers:Netgear R7000, R6400v1, R6400v2, EA6900 (XvortexCFE), E2000, E1200v1, WRT54GS v1.
Install guide R6400v2, R6700v3,XR300:https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=316399
Install guide R7800/XR500: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=320614
Forum Guide Lines (important read):https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=324087
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Index -> Marvell MVEBU based Hardware (WRT1900AC etc.) All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum