Posted: Sat Feb 05, 2022 14:01 Post subject: New Build - 02/05/2022 - r48296
Welcome to Broadcom r48296 beta release thread for reporting, feedback to developers & community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• DNScrypt 1.95 can still be used in WebUIbut v2 (not compatible) requires Golang and thus Entware. See Trac ticket #6246.
• WDS does not work on Broadcom ARM devices (only MIPS<->MIPS) & bridge modes on k4.4 devices may sometimes work
in some configurations for certain builds but are not supported by the bcmdhd driver. Try client or repeater modes, but YMMV.
• VAPs not working at bootare fixed, both unbridged (r40634) and bridged (r47822). Please test, removestartup commands.
• If startup scripts do not work from USB add delay (wait script), sleep 25 or try Administration -> Commands -> Save USB.
• Broadcom ARM devices if 5 GHz channels are missingvia Telnet/SSH: 'nvram set brcm_unlock=1' 'nvram commit' 'reboot'.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs. Logs: 'dmesg' 'cat /tmp/var/log/messages' syslog klog, serial, strace, tcpdump, wireshark.
• Any firewall NAT or WAN issues, show output: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' and /tmp/.ipt file.
• Gremlins: reset & configure manually, not restore a backup. Reboot. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) and applicable configurations to reproduce.
Router/Version: Trendnet TEW811DRU
File/Kernel: Previous/Reset: DD-WRT v3.0-r48218 mini (01/28/22)/no
Mode/Status: Client AP/ Booted ok, reverted to r48218
Issues/Errors: same symptoms as build r48289, GUI accessible - would break on Status_Wireless.asp page, then refuse connections, had to revert via Edge browser after a few retries from Status/Admin page - so issue is reproduceable.
Joined: 29 Sep 2020 Posts: 260 Location: United States
Posted: Sat Feb 05, 2022 20:01 Post subject:
Router Model: Netgear R7000P
Firmware Version: DD-WRT v3.0-r48296 std (02/05/22)
Kernel Version: Linux 4.4.302 #5200 SMP Sat Feb 5 14:05:54 +07 2022 armv7l
Reset: no
Operating Mode/Setup: Gateway / AP Unbound JFFS2
Status: running well. thanks BS and dd-wrt community
Upgraded with a CLI Flash in PuTTY via Secure Shell
When checking settings in GUI I use a Firefox Private Window with no add-ons
Joined: 01 Dec 2021 Posts: 289 Location: Maryland, United States
Posted: Sat Feb 05, 2022 20:44 Post subject:
Router/Version: Netgear R6300v1
Firmware: DD-WRT v3.0-r48296 giga (02/05/22)
File/Kernel: Linux 4.4.302 #14300 Sat Feb 5 14:32:56 +07 2022 mips
Previous/Reset: r47822 No reset
Mode/Status: Gateway / Working
Issues/Errors: None except IPv6.
I have not tested the "Apply Settings" issue which when used caused previous newer builds to disabled the GUI. I then had to do a 30/30/30 reset to allow me to load the OEM Netgear firmware then go back to DD-WRT.
The IPv6 issue has been posted in another post on this thread. The router cannot get a WAN IPv6 address.
Last edited by PaulGo on Sat Feb 19, 2022 21:06; edited 1 time in total
Netgear R6250
Firmware:DD-WRT v3.0-r48296 std (02/05/22)
Kernel: Linux 4.4.302 #5194 SMP Sat Feb 5 06:34:48 +07 2022 armv7l
Upgrade from CUI without reset
Previous: DD-WRT v3.0-r48289 std (02/04/22)
Mode: Gateway, Wireless AP, CTF & FA Enabled. NAT/QoS Off
CPU Clock 800MHz without fan
Load Average 0.01, 0.02, 0.00
Temperatures CPU 80.2 °C / WL0 51.1 °C / WL1 57.0 °C
DNSMasq cache-size=8888
root@DD-WRT:/tmp# dmesg | grep ctf
create ctf proc
attach ctf for eth%d
_ctf_attach:attach eth%d
bind ctf to eth if
_ctf_attach:attach wl0
_ctf_attach:attach wl1
Joined: 18 Mar 2014 Posts: 12877 Location: Netherlands
Posted: Sun Feb 06, 2022 11:45 Post subject:
Router Model: Netgear R6400v1
Firmware Version: DD-WRT v3.0-r48296M Community Build (02/05/22)
Kernel Version: Linux 4.4.302 #1 SMP Sat Feb 5 10:57:26 CET 2022 armv7l
Upgraded from: DD-WRT v3.0-r48218M Community Build (01/27/22)
Reset: No not this time
Status: Up and running for 24 hours, basic setup as Gateway, static leases, Advanced routing, Port Forwarding, IPv4, 2.4 GHz with unbridged VAP and 5 GHz.
Running one WireGuard tunnel to Keepsolid, second WireGuard tunnel to ddwrt WG server for site-to-site connection, third tunnel to Oracle Cloud server.
OpenVPN client tested and working
Joined: 18 Mar 2014 Posts: 12877 Location: Netherlands
Posted: Sun Feb 06, 2022 11:48 Post subject:
Router Model: Netgear R6400v2, board_id: U12H332T
Firmware Version: DD-WRT v3.0-r48296M Community Build (02/05/22)
Kernel Version: Linux 4.4.302 #1 SMP Sat Feb 5 10:57:26 CET 2022 armv7l
Upgraded from: DD-WRT v3.0-r48218M Community Build (01/27/22)
Reset: No not this time
Status: Up and running for 24 hours, basic setup as Gateway, static leases, 2,4GHz and 5Ghz working, USB storage NAS working.
OpenVPN server working.
WireGuard server working with 8 clients (phones, Windows and two other routers for site-to-site setup).
I didn't have any of these problems yet, my trick is to reboot the router before any upgrade, it also prevents bad flash/bootloop (confirmed to work with other Archer C9 v1 & v2 owners).
Netgear R6700 v3 – Client Bridge
Firmware Version: DD-WRT v3.0-r48296 std (02/05/22)
Kernel Version: Linux 4.4.302 #5194 SMP Sat Feb 5 06:34:48 +07 2022 armv7l
Temperatures: CPU 65.8 °C / WL1 53.4 °C
Current Time: Sun, 06 Feb 2022 15:05:08
Uptime: 3 min
Reset: No
GUI install over 48218
GUI Issues with Status Wireless page and Sys-Info page. Back to 48218
Thank you BS and thanks you gurus for your guides and wisdom _________________ Netgear XR500 - Gateway
R6700 v3 - Station Bridge
