Joined: 06 Jun 2006 Posts: 7492 Location: Dresden, Germany
Posted: Fri Feb 04, 2022 8:58 Post subject:
should be already fixed. new testbuilds will pop up within the next minutes _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
Ain't never had a bit of trouble until yesterday I installed r48261 on the stupid broadcomy RTN12D1.
ONLY way I could fix was using its reset button.
When page came up to set UN & PW I had to set root & admin then could navigate to firmware upgrade page and install older build.
Main EA8500 running r48273
up 1 day 13:18
and all its webif pages are perfectly fine.
----
and I didn't mention--->
Linksys EA8500
DD-WRT v3.0-r48289 std (02/04/22)
Linux 4.9.299 #754 SMP Fri Feb 4 13:40:45 +07 2022 armv7l
is perfectly fine on other EA8500 ...gonna leave main as is w/r48273
Joined: 08 May 2018 Posts: 14246 Location: Texas, USA
Posted: Fri Feb 04, 2022 13:48 Post subject:
The issue was possibly revealed due to browser and browser configuration used, IMHO. Most of the "issues" people have had with the webUI, save and except for the expected hiccup after flashing (without reset) because of timing, I have not had. I would have to look deeper, but this was probably not caused by any of the improvements that were submitted by the-j0ker, either. Just glad the anomaly was found and fixed. _________________ "Life is but a fleeting moment, a vapor that vanishes quickly; All is vanity"
Contribute To DD-WRT Pogo - A minimal level of ability is expected and needed... DD-WRT Releases 2023 (PolitePol)
DD-WRT Releases 2023 (RSS Everything)
----------------------
Linux User #377467 counter.li.org / linuxcounter.net
FWIW, my XR500 (Atheros) did not experience any problems but my R6700 v3 (Broadcom) did have the GUI issue using both Brave (Chrome) and Waterfox (Firefox) browsers. I look forward to trying the fixed version. Thank you for all of the hard work that BrainSlayer and all of the Gurus do. It is greatly appreciated. _________________ Netgear XR500 - Gateway
R6700 v3 - Station Bridge
Joined: 21 Jan 2017 Posts: 1783 Location: Illinois Moderator
Posted: Fri Feb 04, 2022 17:54 Post subject:
FWIW, I did try the obvious things at first like using incognito/private browsing on Latest Chrome, Chrome 91 portable, Opera, and Edge. Cleared cache on all and privite modes on all and all yielded the same thing. Either access for the first 30ish seconds and then dead or no access ever.
So far 48289 is solid!
Working from home today and have noticed no other hiccups, yet.
Joined: 16 Nov 2015 Posts: 6447 Location: UK, London, just across the river..
Posted: Fri Feb 04, 2022 18:13 Post subject:
msoengineer wrote:
FWIW, I did try the obvious things at first like using incognito/private browsing on Latest Chrome, Chrome 91 portable, Opera, and Edge. Cleared cache on all and privite modes on all and all yielded the same thing. Either access for the first 30ish seconds and then dead or no access ever.
So far 48289 is solid!
Working from home today and have noticed no other hiccups, yet.
Thanks BS!
Although i don't have any issues with 1043v2 GUI with pale-moon or opera-dev nor ffx...i have a question for you...
msoenginer did you by any chance entered a wrong credential via GUI...?
I did notice some strange behaviour few builds back, as i put the wrong details and than i had to reboot and restart browser as it was throwing err 400 or 401 don't clearly noticed..but currently on 255 or 261 no issues with correct credentials... _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55630 WAP
TP-Link WR1043NDv2 -DD-WRT 55723 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55779 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55819 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55779 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
Joined: 21 Jan 2017 Posts: 1783 Location: Illinois Moderator
Posted: Fri Feb 04, 2022 19:14 Post subject:
Alozaros wrote:
msoengineer wrote:
FWIW, I did try the obvious things at first like using incognito/private browsing on Latest Chrome, Chrome 91 portable, Opera, and Edge. Cleared cache on all and privite modes on all and all yielded the same thing. Either access for the first 30ish seconds and then dead or no access ever.
So far 48289 is solid!
Working from home today and have noticed no other hiccups, yet.
Thanks BS!
Although i don't have any issues with 1043v2 GUI with pale-moon or opera-dev nor ffx...i have a question for you...
msoenginer did you by any chance entered a wrong credential via GUI...?
I did notice some strange behaviour few builds back, as i put the wrong details and than i had to reboot and restart browser as it was throwing err 400 or 401 don't clearly noticed..but currently on 255 or 261 no issues with correct credentials...
No, I know for 100% I entered the right password. That said, several builds back on my remote PC I did bunk pw but that was on a separate machine. So if the router was storing that, it's possible that may have contributed? Dunno... _________________ FORUM RULES
tried to GUI install over r48261
would NOT work NO how NO way looked ok ...but just stayed on the upgrading screen forever
I downloaded file again but was same as I had previously
Joined: 06 Jun 2006 Posts: 7492 Location: Dresden, Germany
Posted: Fri Feb 04, 2022 20:47 Post subject:
mrjcd wrote:
tried to GUI install over r48261
would NOT work NO how NO way looked ok ...but just stayed on the upgrading screen forever
I downloaded file again but was same as I had previously
yeahuh its webif is just fine --- but so was previous build
install it with ssh
copy the webflashfile file to /tmp/firmware.bin and just wait until its done _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
