Posted: Fri Jan 28, 2022 4:30 Post subject: New Build - 01/28/2022 - r48218
Welcome to Marvell r48218 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs. Logs: 'dmesg' 'cat /tmp/var/log/messages' syslog klog, serial, strace, tcpdump, wireshark.
• Any firewall NAT or WAN issues, show output: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' and /tmp/.ipt file.
• Gremlins: reset & configure manually, not restore a backup. Reboot. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) and applicable configurations to reproduce.
Upgrade from 01-21-2022-r48141 build yesterday.
WPA2/WPA3 personal does not work together. It causes all android devices disconnect.It only works WPA2 only.
Uptime only few hours then hard reset by rest button, WRT32x only can access change password page then cannot display anything after apply. (Dead loop)
Never update this Build
Last edited by raywan on Mon Jan 31, 2022 11:28; edited 1 time in total
Posted: Sun Jan 30, 2022 17:02 Post subject: WRT-3200acm - r48218
Iḿ having no joy with either this build or the 48208 i think it was.
I did a full reset prior to flashing and also after flashing but after the intial setting of user and password the wireless tab and security tabs fail to work, even after leaving the router for a few hours to settle down.
Not sure if im missing something here but managed to reflash back to 47225 and all seems well again.
Posted: Sun Jan 30, 2022 17:30 Post subject: Re: WRT-3200acm - r48218
KJB wrote:
Iḿ having no joy with either this build or the 48208 i think it was.
I did a full reset prior to flashing and also after flashing but after the intial setting of user and password the wireless tab and security tabs fail to work, even after leaving the router for a few hours to settle down.
Not sure if im missing something here but managed to reflash back to 47225 and all seems well again.
Anyone else with a similar problem?
me too. I am trying to figure out what is the problem why httpd seems not working.
I flashed r48218 couple of hours without issues but after woke up in the morning. WRT32x cannot connect and cannot access the web management interface. So, i tried hard reset the WRT32x with hard reset bottom few times but no help. It can only display password change page and nothing can been shown after apply.
is there any method is flash back the previous firmware in this situation?
There is a triple power toggle failover method to force switch the boot partition.
It is a pain sometimes to find correct timing, so here are alternate descriptions.
Power ON and when LAN LED is blinking immediately turn it OFF then wait at least three seconds, repeat.
Then power it on a third time and let it run.
Another visual cue is power LED blinks a few times then turns off for about 2 seconds, switch power OFF.
Try nvram show | grep net.ipv4.tcp_tw_ ; if those values are 1, set them to 0 with nvram set then do an nvram commit and then a reboot via telnet or ssh.
Quote:
you should be accessing with Firefox / FF ESR portable, Pale Moon Portable, Waterfox Classic in private browsing mode with no extensions, add-ons, or plugins loaded whatsoever *separate* from your internet surfing.
I can confirm having issues with WPA3 and android devices, also one Linux system I use extensively can not get decent speeds connects at 433/433Mbit but can't reach more than ~30 Mbit (only in linux, same system with Windows 10 is ok). I was on Openwrt 21.02.1 (WPA2 only) and had no issues with the Linux system.
I can confirm having issues with WPA3 and android devices, also one Linux system I use extensively can not get decent speeds connects at 433/433Mbit but can't reach more than ~30 Mbit (only in linux, same system with Windows 10 is ok). I was on Openwrt 21.02.1 (WPA2 only) and had no issues with the Linux system.
I just installed OpenWrt 21.02.1 on the other partition and I can confirm my Linux system gets the speed as expected. I guess this is some bug with DD-WRT and Atheros ATH10k cards in Linux as I used older live distro as a test and it gave the same results (old kernel and userspace tools the ATH10K driver and firmware is mostly without significant changes). _________________ WRT1900ACS v1
