Posted: Fri Jan 28, 2022 4:30 Post subject: New Build - 01/28/2022 - r48218
Welcome to Broadcom r48218 beta release thread for reporting, feedback to developers & community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• DNScrypt 1.95 can still be used in WebUIbut v2 (not compatible) requires Golang and thus Entware. See Trac ticket #6246.
• WDS does not work on Broadcom ARM devices (only MIPS<->MIPS) & bridge modes on k4.4 devices may sometimes work
in some configurations for certain builds but are not supported by the bcmdhd driver. Try client or repeater modes, but YMMV.
• VAPs not working at bootare fixed, both unbridged (r40634) and bridged (r47822). Please test, removestartup commands.
• If startup scripts do not work from USB add delay (wait script), sleep 25 or try Administration -> Commands -> Save USB.
• Broadcom ARM devices if 5 GHz channels are missingvia Telnet/SSH: 'nvram set brcm_unlock=1' 'nvram commit' 'reboot'.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs. Logs: 'dmesg' 'cat /tmp/var/log/messages' syslog klog, serial, strace, tcpdump, wireshark.
• Any firewall NAT or WAN issues, show output: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' and /tmp/.ipt file.
• Gremlins: reset & configure manually, not restore a backup. Reboot. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) and applicable configurations to reproduce.
Joined: 18 Mar 2014 Posts: 12884 Location: Netherlands
Posted: Fri Jan 28, 2022 11:44 Post subject:
Router Model: Netgear R6400v1
Firmware Version: DD-WRT v3.0-r48218M Community Build (01/27/22)
Kernel Version: Linux 4.4.300 #1 SMP Thu Jan 27 16:36:45 CET 2022 armv7l
Upgraded from: DD-WRT v3.0-r48138M Community Build
Reset: No not this time
Status: Up and running for 16 hours, basic setup as Gateway, static leases, IPv4, 2.4 GHz with unbridged VAP and 5 GHz.
Running one WireGuard tunnel to Keepsolid and second WireGuard tunnel to own WG server for site-to-site connection.
OpenVPN client tested and working
Disabled "Query DNs in strict order"
Joined: 18 Mar 2014 Posts: 12884 Location: Netherlands
Posted: Fri Jan 28, 2022 11:49 Post subject:
Router Model: Netgear R6400v2, board_id: U12H332T
Firmware Version: DD-WRT v3.0-r48218M Community Build (01/27/22)
Kernel Version: Linux 4.4.300 #1 SMP Thu Jan 27 16:36:45 CET 2022 armv7l
Upgraded from: DD-WRT v3.0-r48138M Community Build
Reset: No not this time
Status: Up and running for 16 hours, basic setup as Gateway, static leases, 2,4GHz and 5Ghz working, USB storage NAS working.
OpenVPN server working.
WireGuard server working with 8 clients (phones , windows and two other routers for site-to-site setup).
Router/Version: Asus AC-3100
File/Kernel: asus_rt-ac3100-firmware.trx(Experimental)/Linux 4.4.299 #5036 SMP Fri Jan 21 04:34:03 +07 2022 armv7l
Previous/Reset: r48141/no
Mode/Status: NAT/SFE/uPNP/no DHCP,DNS/Wireguard client
Issues/Errors:
Installed 48218 (experimental) with no errors. However, there was no WiFi transmission (2.4 GHz or 5 GHz) even though the status page showed radios working normally (but no connections, of course) and Syslog showed no errors. Did standard reboot with no change. Reverted back to r48141 and all working well.
Linksys E2500
DD-WRT v3.0-r48218 mega (01/28/22)
Linux 4.4.300 #13996 Fri Jan 28 04:15:04 +07 2022 mips
'dd-wrt.v24-48218_NEWD-2_K3.x_mega.bin'
GUI install over r48138
used as a WAP --- all good
#
Linksys E1200 v2
DD-WRT v3.0-r48218 mega (01/28/22)
Linux 4.4.300 #13996 Fri Jan 28 04:15:04 +07 2022 mips
'dd-wrt.v24-48218_NEWD-2_K3.x_mega-nv64k.bin'
GUI install over r48138
used as client bridge --- all ok
Router/Version: Trendnet TEW811DRU / DD-WRT v3.0-r48218 mini (01/28/22)
File/Kernel: Linux 4.4.300 #5088 Fri Jan 28 03:14:45 +07 2022 armv7l
Previous/Reset: DD-WRT v3.0-r48141 mini (01/21/22)/no
Mode/Status: Client AP/ Booted ok, Temps: CPU 80.2 °C / WL0 54.3 °C / WL1 60.1 °C
Issues/Errors: temps appear a bit better than 48255-289, GUI accessible - will recheck later as it worked for a while under r48255 before breaking - thanks BS
occasionally loses connection to hotspot
Last edited by angler on Sat Feb 12, 2022 20:32; edited 1 time in total