Posted: Sun Jan 16, 2022 12:01 Post subject: New Build - 01/16/2022 - r48128
Welcome to Atheros r48128 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs. Logs: 'dmesg' 'cat /tmp/var/log/messages' syslog klog, serial, strace, tcpdump, wireshark.
• Any firewall NAT or WAN issues, show output: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' and /tmp/.ipt file.
• Gremlins: reset & configure manually, not restore a backup. Reboot. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) and applicable configurations to reproduce.
Joined: 05 Oct 2008 Posts: 666 Location: Helsinki, Finland / nr. Alkmaar, Netherlands
Posted: Sun Jan 16, 2022 13:14 Post subject:
Router Model: Netgear R7800
Firmware Version: DD-WRT v3.0-r48128 std (01/16/22)
Kernel Version: Linux 4.9.296 #687 SMP Sun Jan 16 05:27:29 +07 2022 armv7l
Status: Working
Per Yngve Berg wrote:
Errors: On the syslog screen, the Next/Previous buttons are covered by a horizontal scrollbar.
All 13 channels are still shown where some lower and upper channels are used as extensions channel.
On my R7800, upgraded to r48128, the prev/next buttons on the syslog page appear quite normal.
Whenever I pick a different channel from the list 1 - 13, the lower/upper pull-down button adjusts itself immediately to show lower or upper or both as appropriate without saving or applying.
Router Model: Netgear R7800
Firmware Version: DD-WRT v3.0-r48128 std (01/16/22)
Kernel Version: Linux 4.9.296 #687 SMP Sun Jan 16 05:27:29 +07 2022 armv7l
Status: Working
Per Yngve Berg wrote:
Errors: On the syslog screen, the Next/Previous buttons are covered by a horizontal scrollbar.
All 13 channels are still shown where some lower and upper channels are used as extensions channel.
On my R7800, upgraded to r48128, the prev/next buttons on the syslog page appear quite normal.
Whenever I pick a different channel from the list 1 - 13, the lower/upper pull-down button adjusts itself immediately to show lower or upper or both as appropriate without saving or applying.
Linksys EA8500...main gateway
DD-WRT v3.0-r48128 std (01/16/22)
Linux 4.9.296 #685 SMP Sun Jan 16 05:04:25 +07 2022 armv7l
GUI install over r48124
all good
Update method: SSH / CLI
Router/Version: Netgear R9000 Nighthawk X10
File/Kernel: DD-WRT v3.0-r48128 std (01/16/22)
Previous/Reset: DD-WRT v3.0-r48081 std (01/11/22) / No
Mode/Status: Gateway / Working Normally
Issues/Errors: Although the build did load the leases file on reboot, and the Use JFFS2 for client lease DB option was checked, I had to click Apply on the page to get the dnsmasq.leases file to start updating on /jffs. Also, the Active Clients table on the Status, LAN tab had many Hostnames as * until I erased /tmp/dnsmasq.leases. _________________ Netgear R9000
DD-WRT v3.0-r55819 std (04/17/24)
Linux 4.9.337 #722 SMP Wed Apr 17 04:16:49 +07 2024 armv7l
Gateway, AP, DNSMasq, Clock 2000MHz
VAP on wlan1 for internet devices
IPv4 & IPv6 (Prefix Delegation)
Static Leases & DHCP
CloudFlare, no SFE, SmartDNS, no QoS
2.4GHz: Vanilla, Airtime Fairness, NG-Mixed, ACK Timing 3150, WPA2 w/AES & WPA3
5GHz: Vanilla, Airtime Fairness, AC/N Mixed, ACK Timing 3150, WPA2 w/AES & WPA3
2 Netgear AX1800 WiFi Mesh Extenders
Xfinity 1.2Gbps/35Mbps
Netgear WNDR3700 V4
DD-WRT v3.0-r48128 std (01/16/22)
Linux 3.18.140-d6 #134415 Sun Jan 16 09:57:43 +07 2022 mips
used as switch / ovpn server / samba share 16GB ext2 flash drive
all good
Joined: 15 Aug 2016 Posts: 223 Location: Melbourne, Australia
Posted: Mon Jan 17, 2022 3:56 Post subject:
Hi,
Over the last few versions, I noticed that my Netgear R7800 does not SEEM to properly update its Dynamic Domain Name System (DDNS). This results in my repeated failures to remotely connect to its OpenVPN server, from laptop's OpenVPN client.
A manually forced refresh on R7800 to update DDNS indicates that it's updated. But no remote connection trial could get through.
As soon as R7800 is backed down to r47692, I can remotely connect with no problem at all. Not sure what gives?
Would be grateful for help in resolving this issue in order to update beyond r47692 (28th Nov., 2021).
Thank you. _________________ Life is a journey; travel alone makes it less enjoyable and lonely.
Joined: 06 Jun 2006 Posts: 7492 Location: Dresden, Germany
Posted: Mon Jan 17, 2022 16:40 Post subject:
Per Yngve Berg wrote:
Router Model: Netgear R7800
Firmware Version: DD-WRT v3.0-r48128 std (01/16/22)
Kernel Version: Linux 4.9.296 #687 SMP Sun Jan 16 05:27:29 +07 2022 armv7l
Status: Working
Errors: On the syslog screen, the Next/Previous buttons are covered by a horizontal scrollbar.
All 13 channels are still shown where some lower and upper channels are used as extensions channel.
can you post a screenshot to give me a impression what this is about? _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s