New Build - 12/23/2021 - r47911

Post new topic   Reply to topic    DD-WRT Forum Index -> Marvell MVEBU based Hardware (WRT1900AC etc.)
Author Message
blkt
DD-WRT Guru


Joined: 20 Jan 2019
Posts: 4309

PostPosted: Thu Dec 23, 2021 4:53    Post subject: New Build - 12/23/2021 - r47911 Reply with quote
Welcome to Marvell r47911 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specific recovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.


Downloads: HTTPS, FTP

CLI Flash: 'cd /tmp' then 'wget {file URL}' (http only) or 'curl -O {file URL}' (http, https, ftp). 'write {file} linux' then 'reboot'.

Trac SVN: repository since last build r47900 (mirror)

OpenVPN 2.5.5: Changelog, Guides, Server, PBR, DNS, Kill Switch, Watchdog, Reverse PBR, Client, Multiple, tips & scripts.
WireGuard 1.0.20211208/Tools: Changelog, Guides, Client, Server, Advanced, PBR, KS, tips and scripts. Thanks BS & egc!

Notes:
• WRT1200AC, WRT1200AC V2, WRT1900AC, WRT1900AC V2, WRT1900ACS, WRT1900ACS V2, WRT3200ACM and WRT32X.
MiniDLNA, CoovaChilli, Privoxy, iperf3, CAKE, FreeRADIUS, dnsmasq, Unbound, Tor, Squid, Asterisk, OpenSSL, BusyBox, SmartDNS, curl, ProFTPD, mac80211
In-kernel Samba (ksmbd 3.4.2+++) guest behavior now selectable. • WSD updateANTFS/NTFS3 kernel mode driver+++
CVE-2020-26147, CVE-2020-24586, CVE-2020-24587 & CVE-2020-24588 fragattack fixed.
• 'Assign WAN port to Switch' gone, set Connection Type Disabled. • WebUI MAC Filtering (47184-47205). • Sputnik removed.
• 'Ignore WAN DNS' also ignores WAN domain. • Milkfish removed.
New DD-WRT inspired themes conversion by the-joker & BrainSlayer, micro builds excluded, see UI theme test info thread.
• 401 bad request: Ethernet WebUI -> Wireless -> Basic Settings -> Advanced Settings -> Wireless GUI Access Enable, Save

Issues, observations, and/or workarounds reported:
WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!

Important:
• For issues provide applicable info: 'dmesg' 'cat /tmp/var/log/messages', syslog klog, serial, strace, tcpdump, wireshark etc.
• Any firewall NAT or WAN issues, show output: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' and /tmp/.ipt file.
• Gremlins: reset & configure manually, not restore a backup. Reboot. Search Trac & discuss in forum before opening tickets.
• Please include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) & relevant configuration information.

Example Template:
Code:
[b]Router/Version: [/b]
[b]File/Kernel: [/b]
[b]Previous/Reset: [/b]
[b]Mode/Status: [/b]
[b]Issues/Errors: [/b]
Sponsor
Rickers
DD-WRT User


Joined: 10 May 2015
Posts: 66

PostPosted: Fri Dec 24, 2021 3:59    Post subject: Reply with quote
Router/Version: WRT1900ACv1
File/Kernel: ddwrt-linksys-wrt1900ac-webflash.bin, R47911
Previous/Reset: prior 47822/Set Factory Defaults in UI after update and reapplied settings
Mode/Status: AP, sysctl settings at factory defaults
Issues/Errors: None

Things good so far. No 5GHz issues yet with Apple/Android devices.

I did notice that the 'Sensitivity Range (ACK Timing)' item is missing from the Wireless/Basic Settings page.
kernel-panic69
DD-WRT Guru


Joined: 08 May 2018
Posts: 12959
Location: Texas, USA

PostPosted: Fri Dec 24, 2021 15:01    Post subject: Reply with quote
Rickers wrote:
Router/Version: WRT1900ACv1
I did notice that the 'Sensitivity Range (ACK Timing)' item is missing from the Wireless/Basic Settings page.

Is this after clicking the checkbox for "Advanced Settings", where it always has been for non-Broadcom devices?

_________________
"Life is but a fleeting moment, a vapor that vanishes quickly; All is vanity"
Contribute To DD-WRT
Pogo - A minimal level of ability is expected and needed...
At some point, people just get plain tired of this place.
Because they are tired of bottom-feeders and the same old hat.

----------------------
Linux User #377467 counter.li.org / linuxcounter.net
Rickers
DD-WRT User


Joined: 10 May 2015
Posts: 66

PostPosted: Fri Dec 24, 2021 18:46    Post subject: Reply with quote
kernel-panic69 wrote:

Is this after clicking the checkbox for "Advanced Settings", where it always has been for non-Broadcom devices?

Yes. The attached images are from 47692 and 47911. 47822 still had that setting and, when I set Factory Defaults, the value changed to 500 and I left it at that value. On 47911, it's gone.
kernel-panic69
DD-WRT Guru


Joined: 08 May 2018
Posts: 12959
Location: Texas, USA

PostPosted: Fri Dec 24, 2021 20:23    Post subject: Reply with quote
This is for *both* radios, correct? I will forward to BrainSlayer. Not sure if this is intentional or not.

EDIT- This setting is not supported on Marvell (never was, apparently):
Quote:
i check the sources and removed the setting from non supported chipsets. only qca/atheros and mediatek supports it and also broadcom under certain untested conditions

_________________
"Life is but a fleeting moment, a vapor that vanishes quickly; All is vanity"
Contribute To DD-WRT
Pogo - A minimal level of ability is expected and needed...
At some point, people just get plain tired of this place.
Because they are tired of bottom-feeders and the same old hat.

----------------------
Linux User #377467 counter.li.org / linuxcounter.net
Rickers
DD-WRT User


Joined: 10 May 2015
Posts: 66

PostPosted: Sat Dec 25, 2021 1:36    Post subject: Reply with quote
Yes, both 2.4 and 5.
kernel-panic69
DD-WRT Guru


Joined: 08 May 2018
Posts: 12959
Location: Texas, USA

PostPosted: Sat Dec 25, 2021 4:38    Post subject: Reply with quote
And it won't return as Marvell wireless chipsets do not / never did support the function / feature.
_________________
"Life is but a fleeting moment, a vapor that vanishes quickly; All is vanity"
Contribute To DD-WRT
Pogo - A minimal level of ability is expected and needed...
At some point, people just get plain tired of this place.
Because they are tired of bottom-feeders and the same old hat.

----------------------
Linux User #377467 counter.li.org / linuxcounter.net
brucebanner
DD-WRT Novice


Joined: 24 Dec 2021
Posts: 5

PostPosted: Sat Dec 25, 2021 23:58    Post subject: Reply with quote
I am running this build (Firmware: DD-WRT v3.0-r47911 std (12/23/21) for a couple of days on Linksys WRT3200ACM with close to 30 clients, and I do not see any issues. I have 2G and 5G radios enabled and I have clients connected to both.
wrtloop
DD-WRT Novice


Joined: 09 Jan 2021
Posts: 9

PostPosted: Fri Dec 31, 2021 17:11    Post subject: Reply with quote
Router/Version: WRT3200ACM
File/Kernel: Firmware: DD-WRT v3.0-r47911 std (12/23/21)
Previous/Reset: r44048 / Yes / manual configuration from scratch
Mode/Status: Gateway, ipv4 and ipv6, 2.4G and 5G wifi, DHCP, Wireguard "server" for external access, DDNS, Port Forwarding, Keep Alive reboot each day
Issues/Errors: basically None Smile, router runs for a few days now without glitches and it replaced the r44048 version for me.

Note: I had to clear the MTU field for IPV6 configurations to work with my ISP. I also had to set Use external IP check to NO to get the DDNS working. For some ESP devices, I had to set WMM Support to disable in 2.4 GHz wlan.

Clients: iPad Pro, Android Samsung Galaxy S20, 4 ESP devices, Bose SoundTouch, 3 wired PC Windows 10, few Raspberry Pies, Playstation 4, laptops with Win10
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Index -> Marvell MVEBU based Hardware (WRT1900AC etc.) All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum