Posted: Sun Nov 28, 2021 11:05 Post subject: New Build - 11/28/2021 - r47692
[WARNING]: Atheros r47692 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• For issues provide applicable info: 'dmesg', 'cat /tmp/var/log/messages', syslog, klog, serial, strace, tcpdump, wireshark etc.
• Any firewall NAT or WAN issues, show output: 'iptables -vnL', 'iptables -t nat -vnL', 'iptables -t mangle -vnL' and /tmp/.ipt file.
• Search Trac tickets & discuss in forum before opening. Before reporting reset & manually set up, not restore from a backup.
• Please include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) & relevant configuration information.
Status: Up and running for 4 hours , basic setup as Gateway, static leases, 2,4GHz, 5Ghz (Vanilla Firmware), USB storage NAS working, OpenVPN client to Keepsolid with PBR working.
WireGuard client to Keepsolid working , WireGuard client for site-to-site setup to own server working.
WireGuard server(backup for one phone), working
Linksys EA8500...main gateway
DD-WRT v3.0-r47692 std (11/28/21)
Linux 4.9.291 #546 SMP Sat Nov 27 17:05:43 +07 2021 armv7l
GUI install over r47690
static DHCP
local DNS
OVPN server
ext4 samba share encryption required user/PW only
port range forwarding
unbound
both radios good using VANILLA FW
isolated guest net (using target DNS) for wlan0.1 wlan1.1 VLAN on wired port 4 ---> all via br1
HFSC CAKE
All is very good
#
Netgear WNDR3700 V4
DD-WRT v3.0-r47692 std (11/28/21)
Linux 3.18.140-d6 #130010 Sun Nov 28 12:06:46 +07 2021 mips
GUI install over r47665
switch / OVPN server --- everything good
Joined: 14 Sep 2019 Posts: 301 Location: Maine, USA
Posted: Sun Nov 28, 2021 13:41 Post subject:
Router/Version: Netgear WNR2000v3
File: wnr2000v3-webflash.bin
Firmware: DD-WRT v3.0-r47692 std (11/28/21)
Kernel: Linux 3.10.108-d11 #94824 Sun Nov 28 12:12:42 +07 2021 mips
Mode: AP
Previous: r46604
Reset?: N
Status: Working
Upgraded from: DD-WRT v3.0-r47618 std (11/05/21)
Reset: No not this time
Status: Up and running for 6 hours, basic setup as Gateway, static leases, 2.4 GHz and 5 GHz working (vanilla firmware), OpenVPN server working, WireGuard Server working (multiple clients e.g. phone, laptop and site-to-site connection with remote location), NAS and Samba working.
(1) Incoming & Outgoing logs show nothing (not a new issue)
(2) Although the build did load the leases file on reboot, I had to uncheck Use JFFS2 for client lease DB, Apply, re-check and Apply to get leases to start updating to /jffs.
xr500 with bad blocks still bootloops on initial flash. Serial output is the same as before, cannot mount rootfs
Code:
[ 3.543961] No filesystem could mount root, tried: [ 3.545187] squashfs
[ 3.550998]
[ 3.552228] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,6)
Router: Netgear R7800 (272-12536-01)
Firmware: DD-WRT v3.0-r47692 std (11/28/21)
Kernel: Linux 4.9.291 #548 SMP Sun Nov 28 07:18:08 +07 2021 armv7l
Upgraded: from DD-WRT v3.0-r47171 std (08/14/21) via CLI
Reset: nvram erase && reboot
Mode & Uptime: Gateway running OK 3 days
Temperatures: CPU 50 °C / wlan0 47 °C / wlan1 44 °C
Errors: runs fine, but TurboQAM Support option seems to be gone...
Settings: Ignore WAN DNS/disabled SFE/WPA2 AES with Custom Config: basic_rates=60 120 240 supported_rates=60 90 120 180 240 360 480 540/Additional Dnsmasq Options for minor domain-blocking/Port Forwarding/HTB Cake QoS/Elegant Dark Theme/Wireless Settings: