Author
Message
kernel-panic69 DD-WRT Guru Joined: 08 May 2018 Posts: 14223 Location: Texas, USA
Back to top
Sponsor
drnorton DD-WRT User Joined: 08 Dec 2009 Posts: 137
Posted: Thu Nov 25, 2021 9:28 Post subject:
Dynamic Routing is disabled.
I use Router. Only in Gateway Mode
I become dynamic routing.
The Repeater is wired. So I can use it on second floor.
Back to top
|2e4per DD-WRT Novice Joined: 12 Jun 2007 Posts: 32 Location: Aachen, Germany
Posted: Sat Nov 27, 2021 7:54 Post subject:
Per Yngve Berg wrote: swconfig dev switch0 vlan 1 set ports="0 1 2 3 4 5t"
swconfig dev switch0 vlan 2 set ports="5t"
swconfig dev switch0 set apply
I think you can safely drop out the second line concerning vlan2 and uncheck it in the switch config gui also.
Furthermore I strongly recommend a powercylce after taking those changes and save apply in the gut.
I saw my R7000P several times struggling after taking such changes without powercycle.. _________________|2e4per
all running site-to-site OpenVPN
4x WRT54GL v1.1 @ 14929
1x WRT320N chang'd to E2000 bricked -> debricked @ v3.0-r29519 mega
1x Archer C7 v2.0 @ v3.0-r29519 std
1x Archer C7 v4.0 @ v3.0-r35874 std
1x ASUS RT-AC68U H/W ver.E1 @ v3.0-r36070M kongac
2x Netgear R7000P @ v3.0-r36070M kongac
Back to top
drnorton DD-WRT User Joined: 08 Dec 2009 Posts: 137
Posted: Sat Nov 27, 2021 15:01 Post subject:
Hi ...
I become some error after the command:
Unknown attribute "ports=0 1 2 3 4 5t"
Is it the right syntax ?
Back to top
Per Yngve Berg DD-WRT Guru Joined: 13 Aug 2013 Posts: 6868 Location: Romerike, Norway
Posted: Sat Nov 27, 2021 15:46 Post subject:
Did you enter the quotes?
Back to top
|2e4per DD-WRT Novice Joined: 12 Jun 2007 Posts: 32 Location: Aachen, Germany
Posted: Sat Nov 27, 2021 16:29 Post subject:
drnorton wrote:
Unknown attribute "ports=0 1 2 3 4 5t"
No you set the first " in wrong place. It should be right after the equal sign. _________________|2e4per
all running site-to-site OpenVPN
4x WRT54GL v1.1 @ 14929
1x WRT320N chang'd to E2000 bricked -> debricked @ v3.0-r29519 mega
1x Archer C7 v2.0 @ v3.0-r29519 std
1x Archer C7 v4.0 @ v3.0-r35874 std
1x ASUS RT-AC68U H/W ver.E1 @ v3.0-r36070M kongac
2x Netgear R7000P @ v3.0-r36070M kongac
Back to top
drnorton DD-WRT User Joined: 08 Dec 2009 Posts: 137
Posted: Sun Nov 28, 2021 12:47 Post subject:
I used this commands:
Code:
swconfig dev switch0 vlan 1 set ports="0 1 2 3 4 5t"
swconfig dev switch0 vlan 2 set ports="5t"
swconfig dev switch0 set apply
And the result was:
Unknown attribute "ports=0 1 2 3 4 5t"
Even I set the " at the right place behind the equal sign. Mhhmm...
Back to top
|2e4per DD-WRT Novice Joined: 12 Jun 2007 Posts: 32 Location: Aachen, Germany
Posted: Sun Nov 28, 2021 12:56 Post subject:
Did you use them line by line ?
or did you throw it all in ?
I would recommend to ssh into the device and on console at least it should work. _________________|2e4per
all running site-to-site OpenVPN
4x WRT54GL v1.1 @ 14929
1x WRT320N chang'd to E2000 bricked -> debricked @ v3.0-r29519 mega
1x Archer C7 v2.0 @ v3.0-r29519 std
1x Archer C7 v4.0 @ v3.0-r35874 std
1x ASUS RT-AC68U H/W ver.E1 @ v3.0-r36070M kongac
2x Netgear R7000P @ v3.0-r36070M kongac
Back to top
the-joker DD-WRT Developer/Maintainer Joined: 31 Jul 2021 Posts: 2146 Location: All over YOUR webs
Back to top
Per Yngve Berg DD-WRT Guru Joined: 13 Aug 2013 Posts: 6868 Location: Romerike, Norway
Posted: Sun Nov 28, 2021 13:24 Post subject:
The equalizer sign shall be a space.
swconfig dev switch0 vlan 1 set ports "0 1 2 3 4 5t"
Back to top
|2e4per DD-WRT Novice Joined: 12 Jun 2007 Posts: 32 Location: Aachen, Germany
Posted: Sun Nov 28, 2021 13:30 Post subject:
You're right. There shouldn't be an eqal sign.
My bad, appologizes. _________________|2e4per
all running site-to-site OpenVPN
4x WRT54GL v1.1 @ 14929
1x WRT320N chang'd to E2000 bricked -> debricked @ v3.0-r29519 mega
1x Archer C7 v2.0 @ v3.0-r29519 std
1x Archer C7 v4.0 @ v3.0-r35874 std
1x ASUS RT-AC68U H/W ver.E1 @ v3.0-r36070M kongac
2x Netgear R7000P @ v3.0-r36070M kongac
Back to top
drnorton DD-WRT User Joined: 08 Dec 2009 Posts: 137
Posted: Mon Nov 29, 2021 16:19 Post subject:
hihihihi...
Don't worry.
Now is running. And I can use the WAN Post as LAN Port.
Thanks a lot
Back to top