The factory to dd-wrt is for installing DD-WRT from the Linksys GUI. This file will be used under two circumstances.
1. You are installing DD-WRT for the first time.
2. You have switched back to opposite partition and you have the Linksys Stock Firmware on that partition.
Everything work great
in my wrt3200AM on ddwrt (test with speedchecker Tab)always my 50 mbps here
i have connect my Alcatel Lucent router to Wan of my Linksys
I see this is your first post. Welcome to this forum. I am sure someone will be able to help you.
But you have spent 49 Euros to buy the connection. Shouldn't you make Cyberghost earn their money by helping you with the first-time installation? They should take your system in remote and do this for the first time user - else you should ask for a refund. I did this with another provider who were reluctant to help.
https://forum.dd-wrt.com/phpBB2/viewtopic.php?p=1141826#1141826 _________________ PROFESSIONAL STUDENT my.Mistakes ∝ my.Learning ... provided I have the patience & persistence to learn
I see this is your first post. I am sure someone in the forum will be able to help you.
But you have spent 49 Euros to buy the connection. Shouldn't you make Cyberghost earn their money by helping you with the first-time installation? They should take your system in remote and do this for the first time user - else you should ask for a refund. I did this with another provider who were reluctant to help.
https://forum.dd-wrt.com/phpBB2/viewtopic.php?p=1141826#1141826
hello thank you for your answer, I have buy it today, I have send a message today too.
I'm waiting answer, I have a 30 days money back if until Wednesday I have no answer, I'll ask a refund thank you for your help.
I am not a user of CyberGhost ... but there is one error that I could see at quick glance. This is an error in your dd-wrt setup.
Image 1: Basic Setup page ...
Under Network Setup -> Router IP (middle of the image)
Gateway and Local DNS - both should be left at 0.0.0.0 (You have changed these)
Try to change that and see if it works.
If it does ... cheers !!
If it does not ... wait for some CyberGhost expert (I did not read the links that you provided) _________________ PROFESSIONAL STUDENT my.Mistakes ∝ my.Learning ... provided I have the patience & persistence to learn
I am not a user of CyberGhost ... but there is one error that I could see at quick glance. This is an error in your dd-wrt setup.
Image 1: Basic Setup page ...
Under Network Setup -> Router IP (middle of the image)
Gateway and Local DNS - both should be left at 0.0.0.0 (You have changed these)
Try to change that and see if it works.
If it does ... cheers !!
If it does not ... wait for some CyberGhost expert (I did not read the links that you provided)
hello thank you for your help,
i have make the change but nothing
do you think is important to be at 192.168.1.1 like you ?
do you think is important to be at 192.168.1.1 like you ?
No. But do keep the Gateway and the Local DNS at 0.0.0.0 (default) - else you will have other complications (unless CyberGhost asks you to do some changes here - which is very unlikely)
I am not using CyberGhost and neither have I read their tutorials. Guess you need to wait now till someone experienced in CyberGhost responds - or till you get a response from their techsupport.
All the best !! _________________ PROFESSIONAL STUDENT my.Mistakes ∝ my.Learning ... provided I have the patience & persistence to learn
Just one more thing.
Here, the experts make changes to dd-wrt and post for users to give feedback. Once they are certain that a version is stable for a router, they recommend this on the "Supported Routers" wiki ...
https://wiki.dd-wrt.com/wiki/index.php/Supported_Devices
This wiki recommends build 30605 as stable for WRT3200ACM. Is this the same as your router WRT3200ACME? Please check if your router is supported.
You are using the 37139 (which also seems to be for WRT3200ACM - but in beta testing and not yet declared as stable).
Although there is no reason why 37139 should not work, for first time installation, it is always advisable to use the stable build. If you have time to spare - you could try to install build 30605 and then start from zero.
Else, I suggest you wait till cyberghost support reverts back - or some cyberghost user from this forum responds. _________________ PROFESSIONAL STUDENT my.Mistakes ∝ my.Learning ... provided I have the patience & persistence to learn
Just one more thing.
Here, the experts make changes to dd-wrt and post for users to give feedback. Once they are certain that a version is stable for a router, they recommend this on the "Supported Routers" wiki ...
https://wiki.dd-wrt.com/wiki/index.php/Supported_Devices
This wiki recommends build 30605 as stable for WRT3200ACM. Is this the same as your router WRT3200ACME? Please check if your router is supported.
You are using the 37139 (which also seems to be for WRT3200ACM - but in beta testing and not yet declared as stable).
Although there is no reason why 37139 should not work, for first time installation, it is always advisable to use the stable build. If you have time to spare - you could try to install build 30605 and then start from zero.
Else, I suggest you wait till cyberghost support reverts back - or some cyberghost user from this forum responds.
hello how are you today,
I'm at work for the journey when I'll go home tonight I'll change the firmware to test
Joined: 18 Mar 2014 Posts: 12837 Location: Netherlands
Posted: Mon Oct 08, 2018 14:52 Post subject:
Your username and password can be entered in the GUI (like you did) so do not insert:
Code:
auth-user-pass /tmp/key.txt
in additional config and do not enter anythng in Commands/Startup (remove that picture it gives your username and password).
The line in your additional config which is shown in your picture seems wrong, resolv-retry infinite should be on the following line, this could be the cause of your problem
I would suggest not placing anything at all in Additional config, all important things can be done in the GUI.
You can add:
Code:
reneg-sec 0
keepalive 10 120
remote-cert-tls server
Do not use any firewall rules, just tick NAT and Firewall (like you did)
Your username and password can be entered in the GUI (like you did) so do not insert:
Code:
auth-user-pass /tmp/key.txt
in additional config and do not enter anythng in Commands/Startup (remove that picture it gives your username and password).
The line in your additional config which is shown in your picture seems wrong, resolv-retry infinite should be on the following line, this could be the cause of your problem
I would suggest not placing anything at all in Additional config, all important things can be done in the GUI.
You can add:
Code:
reneg-sec 0
keepalive 10 120
remote-cert-tls server
Do not use any firewall rules, just tick NAT and Firewall (like you did)
Try another server/port
Try another build
hello you're right I have make a mistake with my connexion password on the picture I have remove this in cyber ghost, I have create a new.
- nothing in additional config from cyber ghost
- nothing in command startup from cyber ghost
- no firewall rules from cyber ghost
- no change firmware last build beta October
- no change server at my side (French)
- same port from cyber ghost
- add in additional config
Quote:
reneg-sec 0
keepalive 10 120
remote-cert-tls server
I don't know why the configs on the VPN don't work for you. I have recently out the configurations on my PC, and they seem to work really nice. Maybe there is something wrong with your wifi settings.