Posted: Sat Nov 06, 2021 1:49 Post subject: New Build - 11/05/2021 - r47618
[WARNING]: This thread is only for feedback on this beta release for developers and the community's benefit.
DO NOT flash this beta release unless you understand the risks involved and device specificrecovery methods.
Avoid discussions! Create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• For issues provide applicable info: 'dmesg', 'cat /tmp/var/log/messages', syslog, klog, serial, strace, tcpdump, wireshark etc.
• Any firewall NAT or WAN issues, show output: 'iptables -vnL', 'iptables -t nat -vnL', 'iptables -t mangle -vnL' and /tmp/.ipt file.
• Search Trac tickets & discuss in forum before opening. Before reporting reset & manually set up, not restore from a backup.
• Please include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) & relevant configuration information.
This one is a head scratcher, I downloaded the web flash image ddwrt-linksys-wrt3200acm-webflash.bin for my Linksys-wrt3200ACM (that's the FTP folder) and... when I upgrade, I end up with the 10/28/2021 build r47608.
Turns out, the hashes for that file are identical.
Update: I don't know if it was a windows glitch or blkt fixing it, but it did download a different file.
I'm going to go with the windows glitch. Using mac or linux from now on for these. _________________ Router: Linksys WRT3200ACM WLAN0 and 1 have same SSID
88W8964 802.11ac WLAN0 Mode AP VHT80 80MHz Mixed Mode Channel and Extension Channel Auto Extension LL-6
88W8964 802.11ac WLAN1 Mode AP 20 MHz Mixed Mode Channel Auto
SD8887 802.11ac disabled but visible on GUI and CLI
TX Power 18 dBm
Antenna Gain 0 dBi
U-APSD (Automatic Power Save)Enabled
Protection Mode None
RTS Threshold Disabled
Short Preamble Disabled
Short GI Enabled
Single User Beamforming Enabled
Multi User Beamforming Enabled
AP Isolation Disabled
Beacon Interval 100
DTIM Interval 2
WMM Support Enabled
Radar Detection Disabled
ScanList default
Sensitivity Range (ACK Timing) 500 (Default: 500 meters)
Max Associated Clients 256 (Default: 256 Clients)
Minimum Signal for authenticate -128
Minimum Signal for connection -128
Poll Time for signal lookup 10
Amount of allowed low signals 3
Wireless security is WPA2 Personal CCMP-128 only
QAM256 is on
Last edited by Argenis on Wed Nov 10, 2021 8:43; edited 1 time in total
Joined: 12 Dec 2007 Posts: 783 Location: Pittsburgh, PA USA
Posted: Tue Nov 09, 2021 22:39 Post subject:
Router/Version: WRT1900AC v1
File/Kernel: DD-WRT v3.0-r47618 std (11/05/21)
Previous/Reset: r47377, no reset
Mode/Status: Gateway, OpenVPN/Wireguard server
Issues/Errors: Had to flash the firmware twice in the GUI, as the first time it showed as successful but left me at r47377. No issues since upgrade, however. _________________ __________________________
Netgear R7800
DD-WRT v3.0 STD
Linksys WRT1900AC
DD-WRT v3.0 STD
Router/Version: WRT3200ACM
File/Kernel: ddwrt-linksys-wrt3200acm-webflash.bin
Previous/Reset: 10/28/2021 build r47608 No Reset
Mode/Status: Gateway/router
Issues/Errors: None, all I use seems good. Initial entry into GUI for management took a bit but subsequent ones seem fine. _________________ Router: Linksys WRT3200ACM WLAN0 and 1 have same SSID
88W8964 802.11ac WLAN0 Mode AP VHT80 80MHz Mixed Mode Channel and Extension Channel Auto Extension LL-6
88W8964 802.11ac WLAN1 Mode AP 20 MHz Mixed Mode Channel Auto
SD8887 802.11ac disabled but visible on GUI and CLI
TX Power 18 dBm
Antenna Gain 0 dBi
U-APSD (Automatic Power Save)Enabled
Protection Mode None
RTS Threshold Disabled
Short Preamble Disabled
Short GI Enabled
Single User Beamforming Enabled
Multi User Beamforming Enabled
AP Isolation Disabled
Beacon Interval 100
DTIM Interval 2
WMM Support Enabled
Radar Detection Disabled
ScanList default
Sensitivity Range (ACK Timing) 500 (Default: 500 meters)
Max Associated Clients 256 (Default: 256 Clients)
Minimum Signal for authenticate -128
Minimum Signal for connection -128
Poll Time for signal lookup 10
Amount of allowed low signals 3
Wireless security is WPA2 Personal CCMP-128 only
QAM256 is on
Posted: Sat Nov 13, 2021 18:22 Post subject: Re: New Build - 11/05/2021 - r47618
Router/Version: WRT3200ACM
File/Kernel: ddwrt-linksys-wrt3200acm-webflash.bin / BusyBox v1.34.1 (2021-11-05 05:34:38 +07) built-in shell (ash)
Previous/Reset: 11/24/2020 build r44863 No Reset
Mode/Status: Gateway/router
Issues/Errors: I had some issues to register a user some time ago, and did not take more time to give a try. So basically the following issue has been ongoing for a while with all newer builds than r44863. After a while, usually around 24 hours the AP just disappear. o_O The only AP I can see now is on wlan1.1. All the others are gone. After a reboot of the router, I did not have to wait 15 minutes before the issue occurred again. Any clue?
Router/Version: Linksys/Marvell WRT1900ACv1 - coffeejar
File/Kernel: ddwrt-svn47618-wrt1900ac-webflash.bin
Previous/Reset: r44048, no reset
Mode/Status: AP only
Router/Version: Linksys/Marvell WRT1900ACv1 - teajar
File/Kernel: ddwrt-svn47618-wrt1900ac-webflash.bin
Previous/Reset: r44048, no reset
Mode/Status: AP only
All devices boradcasting <ssid> & <ssid>-5 on the 2.4GHz & 5GHz bands respectively, using WPA2 + AES
All looking good so far after ~48 hours of use, with a mix of Windows 10, iOS 15, android, chromecast/fire stick/smart TV devices _________________ All the best,