Posted: Thu Oct 28, 2021 14:50 Post subject: New Build - 10/28/2021 - r47608
[WARNING]: This thread is only for feedback on this beta release for developers and the community's benefit.
DO NOT flash this beta release unless you understand the risks involved and device specificrecovery methods.
Avoid discussions! Create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues:
• Show us your findings with steps to reproduce, configuration, output, logs and important information below!
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
Important:
• For issues provide applicable info: 'dmesg', 'cat /tmp/var/log/messages', syslog, klog, serial, strace, tcpdump, wireshark etc.
• Any firewall NAT or WAN issues, show output: 'iptables -vnL', 'iptables -t nat -vnL', 'iptables -t mangle -vnL' and /tmp/.ipt file.
• Search SVN tickets & discuss in forum before opening. Before reporting: reset & manually set up, not restore from a backup.
• Please include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) & relevant configuration information.
DDWRT worked for a few minutes, but then started to drop connection.
Code:
Oct 28 12:20:06 MAIN user.info : [servicemanager] : waiting for services to finish (1)...
Oct 28 12:20:06 MAIN user.info : [bridge] : interface vlan1 successfully deleted from bridge br0
Oct 28 12:20:06 MAIN kern.info kernel: [ 256.160000] device vlan1 left promiscuous mode
Oct 28 12:20:06 MAIN kern.info kernel: [ 256.160000] device eth0 left promiscuous mode
Oct 28 12:20:06 MAIN kern.info kernel: [ 256.170000] br0: port 1(vlan1) entered disabled state
Oct 28 12:20:06 MAIN user.info : [bridge] : interface wlan0 successfully deleted from bridge br0
Oct 28 12:20:06 MAIN user.info : [bridge] : interface wlan1 successfully deleted from bridge br0
Oct 28 12:20:06 MAIN kern.info kernel: [ 256.180000] device wlan0 left promiscuous mode
Oct 28 12:20:06 MAIN kern.info kernel: [ 256.190000] br0: port 2(wlan0) entered disabled state
Oct 28 12:20:06 MAIN kern.info kernel: [ 256.200000] device wlan1 left promiscuous mode
Oct 28 12:20:06 MAIN kern.info kernel: [ 256.200000] br0: port 3(wlan1) entered disabled state
Oct 28 12:20:06 MAIN user.info : [bridge] : bridge br0 successfully deleted
Oct 28 12:20:06 MAIN user.info : [hostapd] : hostapd daemon successfully stopped
Oct 28 12:20:06 MAIN user.info : [bridge] : interface wlan0 successfully deleted from bridge br0
Oct 28 12:20:06 MAIN user.info : [bridge] : interface wlan1 successfully deleted from bridge br0
Oct 28 12:20:06 MAIN user.info : [bridge] : bridge br0 successfully added
Oct 28 12:20:06 MAIN kern.info kernel: [ 256.730000] device br0 entered promiscuous mode
Oct 28 12:20:06 MAIN user.info : [bridge] : interface vlan1 successfully added to bridge br0
Oct 28 12:20:06 MAIN kern.info kernel: [ 256.820000] device vlan1 entered promiscuous mode
Oct 28 12:20:06 MAIN kern.info kernel: [ 256.830000] device eth0 entered promiscuous mode
Oct 28 12:20:06 MAIN kern.info kernel: [ 256.840000] br0: port 1(vlan1) entered forwarding state
Oct 28 12:20:06 MAIN kern.info kernel: [ 256.840000] br0: port 1(vlan1) entered forwarding state
Oct 28 12:20:06 MAIN kern.info kernel: [ 256.870000] device br0 left promiscuous mode
Oct 28 12:20:06 MAIN kern.info kernel: [ 256.880000] device br0 entered promiscuous mode
Oct 28 12:20:06 MAIN kern.info kernel: [ 256.900000] device br0 left promiscuous mode
Oct 28 12:20:07 MAIN kern.debug kernel: [ 257.030000] ath: EEPROM regdomain: 0x8348
Oct 28 12:20:07 MAIN kern.debug kernel: [ 257.030000] ath: EEPROM indicates we should expect a country code
Oct 28 12:20:07 MAIN kern.debug kernel: [ 257.030000] ath: doing EEPROM country->regdmn map search
Oct 28 12:20:07 MAIN kern.debug kernel: [ 257.030000] ath: country maps to regdmn code: 0x3a
Oct 28 12:20:07 MAIN kern.debug kernel: [ 257.030000] ath: Country alpha2 being used: US
Oct 28 12:20:07 MAIN kern.debug kernel: [ 257.030000] ath: Regpair used: 0x3a
Oct 28 12:20:07 MAIN kern.debug kernel: [ 257.030000] ath: regdomain 0x8348 dynamically updated by user
Oct 28 12:20:07 MAIN kern.debug kernel: [ 257.030000] ath: EEPROM regdomain: 0x8348
Oct 28 12:20:07 MAIN kern.debug kernel: [ 257.030000] ath: EEPROM indicates we should expect a country code
Oct 28 12:20:07 MAIN kern.debug kernel: [ 257.030000] ath: doing EEPROM country->regdmn map search
Oct 28 12:20:07 MAIN kern.debug kernel: [ 257.030000] ath: country maps to regdmn code: 0x3a
Oct 28 12:20:07 MAIN kern.debug kernel: [ 257.030000] ath: Country alpha2 being used: US
Oct 28 12:20:07 MAIN kern.debug kernel: [ 257.030000] ath: Regpair used: 0x3a
Oct 28 12:20:07 MAIN kern.debug kernel: [ 257.030000] ath: regdomain 0x8348 dynamically updated by user
Oct 28 12:20:07 MAIN kern.info kernel: [ 257.330000] device wlan0 entered promiscuous mode
Oct 28 12:20:09 MAIN kern.info kernel: [ 259.020000] br0: port 2(wlan0) entered forwarding state
Oct 28 12:20:09 MAIN kern.info kernel: [ 259.030000] br0: port 2(wlan0) entered forwarding state
Oct 28 12:20:09 MAIN user.info : [bridge] : interface wlan0 successfully added to bridge br0
Oct 28 12:20:09 MAIN kern.info kernel: [ 259.120000] ath10k_pci 0000:00:00.0: user requested fw restart
Oct 28 12:20:09 MAIN kern.warn kernel: [ 259.230000] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:00:00.0.bin failed with error -2
Oct 28 12:20:09 MAIN kern.warn kernel: [ 259.240000] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/cal-pci-0000:00:00.0.bin failed with error -2
Oct 28 12:20:09 MAIN kern.warn kernel: [ 259.250000] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-6.bin failed with error -2
Oct 28 12:20:09 MAIN kern.info kernel: [ 259.260000] ath10k_pci 0000:00:00.0: found firmware features ie (4 B)
Oct 28 12:20:09 MAIN kern.info kernel: [ 259.270000] ath10k_pci 0000:00:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
Oct 28 12:20:09 MAIN kern.info kernel: [ 259.280000] ath10k_pci 0000:00:00.0: kconfig debug 1 debugfs 1 tracing 0 dfs 0 testmode 0
Oct 28 12:20:09 MAIN kern.info kernel: [ 259.290000] ath10k_pci 0000:00:00.0: firmware ver 10.2.4-97.2-ddwrt-6301M api 5 features wmi-10.x,no-p2p,wmi-10.2,raw-mode,mfp,allows-mesh-bcast,peer-fixed-rate crc32 69ddfd64
Oct 28 12:20:09 MAIN kern.info kernel: [ 259.340000] ath10k_pci 0000:00:00.0: boot get otp board id result 0x00000001 board_id 0 chip_id 0 ext_bid_support 0
Oct 28 12:20:09 MAIN kern.info kernel: [ 259.350000] ath10k_pci 0000:00:00.0: board id does not exist in otp, ignore it (-2144456272)
Oct 28 12:20:09 MAIN kern.info kernel: [ 259.360000] ath10k_pci 0000:00:00.0: boot using board name 'bus=pci,vendor=168c,device=003c,subsystem-vendor=0000,subsystem-device=0000'
Oct 28 12:20:09 MAIN kern.info kernel: [ 259.370000] ath10k_pci 0000:00:00.0: boot using board name 'bus=pci,vendor=168c,device=003c,subsystem-vendor=0000,subsystem-device=0000'
Oct 28 12:20:09 MAIN kern.warn kernel: [ 259.380000] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
Oct 28 12:20:09 MAIN kern.info kernel: [ 259.390000] ath10k_pci 0000:00:00.0: board_file api 1 bmi_id N/A crc32 aaa71214
Oct 28 12:20:09 MAIN kern.info kernel: [ 259.410000] ath10k_pci 0000:00:00.0: boot upload otp to 0x1234 len 6209
Oct 28 12:20:09 MAIN kern.warn kernel: [ 259.440000] ath10k_pci 0000:00:00.0: otp stream is empty, using board.bin contents
Oct 28 12:20:10 MAIN kern.info kernel: [ 260.350000] ath10k_pci 0000:00:00.0: Init Max Stations to 118
Oct 28 12:20:10 MAIN kern.info kernel: [ 260.360000] ath10k_pci 0000:00:00.0: P 135 V 16 T 433
Oct 28 12:20:10 MAIN kern.info kernel: [ 260.370000] ath10k_pci 0000:00:00.0: alloc rem: 9492 iram: 42308
Oct 28 12:20:10 MAIN kern.info kernel: [ 260.380000] ath10k_pci 0000:00:00.0: wmi event ready sw_version 0x41000061 abi_version 1 mac_addr d8:47:32:59:93:d3 status 0
Oct 28 12:20:10 MAIN kern.info kernel: [ 260.390000] ath10k_pci 0000:00:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta 118 raw 0 hwcrypto 1
Oct 28 12:20:13 MAIN kern.warn kernel: [ 263.540000] ath10k_pci 0000:00:00.0: wmi command 36870 timeout, restarting hardware
Oct 28 12:20:13 MAIN kern.warn kernel: [ 263.540000] ath10k_pci 0000:00:00.0: ani_enable failed from debugfs: -11
Oct 28 12:20:13 MAIN kern.warn kernel: [ 263.550000] ath10k_pci 0000:00:00.0: cannot restart a device that hasn't been started
Oct 28 12:20:13 MAIN kern.info kernel: [ 263.870000] ath10k_pci 0000:00:00.0: boot upload otp to 0x1234 len 6209
Oct 28 12:20:13 MAIN kern.warn kernel: [ 263.900000] ath10k_pci 0000:00:00.0: otp stream is empty, using board.bin contents
Oct 28 12:20:14 MAIN kern.info kernel: [ 264.810000] ath10k_pci 0000:00:00.0: Init Max Stations to 118
Oct 28 12:20:14 MAIN kern.info kernel: [ 264.820000] ath10k_pci 0000:00:00.0: P 135 V 16 T 433
Oct 28 12:20:14 MAIN kern.info kernel: [ 264.830000] ath10k_pci 0000:00:00.0: alloc rem: 9492 iram: 42308
Oct 28 12:20:14 MAIN kern.info kernel: [ 264.840000] ath10k_pci 0000:00:00.0: wmi event ready sw_version 0x41000061 abi_version 1 mac_addr d8:47:32:59:93:d3 status 0
Oct 28 12:20:14 MAIN kern.warn kernel: [ 264.850000] ath10k_pci 0000:00:00.0: pdev param 0 not supported by firmware
Oct 28 12:20:14 MAIN kern.warn kernel: [ 264.870000] ath10k_pci 0000:00:00.0: failed to set vdev 0 tx encap mode: -122
Oct 28 12:20:14 MAIN kern.info kernel: [ 264.890000] device wlan1 entered promiscuous mode
Oct 28 12:20:15 MAIN kern.info kernel: [ 265.320000] br0: port 3(wlan1) entered forwarding state
Oct 28 12:20:15 MAIN kern.info kernel: [ 265.320000] br0: port 3(wlan1) entered forwarding state
Oct 28 12:20:15 MAIN user.info : [bridge] : interface wlan1 successfully added to bridge br0
Oct 28 12:20:15 MAIN user.info : [dnsmasq] : daemon successfully stopped
Oct 28 12:20:16 MAIN user.info : [dnsmasq] : daemon successfully started
Oct 28 12:20:19 MAIN user.info : [httpd] : daemon successfully stopped
Oct 28 12:20:19 MAIN daemon.info httpd[1296]: [httpd] : httpd server shutdown
Oct 28 12:20:19 MAIN daemon.info httpd[3817]: [httpd] : httpd server started at port 80
Oct 28 12:20:19 MAIN user.info : [httpd] : http daemon successfully started
Oct 28 12:20:21 MAIN kern.info kernel: [ 271.880000] br0: port 1(vlan1) entered forwarding state
Oct 28 12:20:24 MAIN kern.info kernel: [ 274.080000] br0: port 2(wlan0) entered forwarding state
Oct 28 12:20:28 MAIN kern.info kernel: [ 278.250000] ath10k_pci 0000:00:00.0: consec fail!!
Oct 28 12:20:28 MAIN kern.info kernel: [ 278.660000] ath10k_pci 0000:00:00.0: consec fail!!
Oct 28 12:20:29 MAIN kern.info kernel: [ 279.010000] ath10k_pci 0000:00:00.0: consec fail!!
Oct 28 12:20:29 MAIN kern.info kernel: [ 279.700000] ath10k_pci 0000:00:00.0: consec fail!!
Oct 28 12:20:30 MAIN kern.info kernel: [ 280.060000] ath10k_pci 0000:00:00.0: consec fail!!
Oct 28 12:20:30 MAIN kern.info kernel: [ 280.360000] br0: port 3(wlan1) entered forwarding state
Oct 28 12:20:46 MAIN kern.info kernel: [ 296.280000] ath10k_pci 0000:00:00.0: consec fail!!
Oct 28 12:20:50 MAIN kern.info kernel: [ 300.860000] ath10k_pci 0000:00:00.0: consec fail!!
Oct 28 12:20:52 MAIN kern.info kernel: [ 302.100000] ath10k_pci 0000:00:00.0: consec fail!!
Oct 28 12:20:52 MAIN kern.info kernel: [ 302.750000] ath10k_pci 0000:00:00.0: consec fail!!
Oct 28 12:20:53 MAIN kern.info kernel: [ 303.570000] ath10k_pci 0000:00:00.0: consec fail!!
Oct 28 12:21:00 MAIN kern.info kernel: [ 310.760000] ath10k_pci 0000:00:00.0: consec fail!!
Oct 28 12:21:01 MAIN kern.info kernel: [ 311.120000] ath10k_pci 0000:00:00.0: consec fail!!
Oct 28 12:21:01 MAIN kern.info kernel: [ 311.480000] ath10k_pci 0000:00:00.0: consec fail!!
Oct 28 12:21:02 MAIN kern.info kernel: [ 312.440000] ath10k_pci 0000:00:00.0: consec fail!!
Oct 28 12:21:02 MAIN kern.info kernel: [ 312.790000] ath10k_pci 0000:00:00.0: consec fail!!
Oct 28 12:21:10 MAIN kern.info kernel: [ 320.530000] ath10k_pci 0000:00:00.0: consec fail!!
Oct 28 12:21:11 MAIN kern.info kernel: [ 321.720000] ath10k_pci 0000:00:00.0: consec fail!!
Oct 28 12:21:12 MAIN kern.info kernel: [ 322.080000] ath10k_pci 0000:00:00.0: consec fail!!
Oct 28 12:21:15 MAIN kern.info kernel: [ 325.860000] ath10k_pci 0000:00:00.0: consec fail!!
Oct 28 12:21:19 MAIN kern.info kernel: [ 329.650000] ath10k_pci 0000:00:00.0: consec fail!!
Oct 28 12:21:20 MAIN kern.info kernel: [ 330.700000] ath10k_pci 0000:00:00.0: consec fail!!
Oct 28 12:21:22 MAIN kern.info kernel: [ 332.220000] ath10k_pci 0000:00:00.0: consec fail!!
Oct 28 12:21:22 MAIN kern.info kernel: [ 332.840000] ath10k_pci 0000:00:00.0: consec fail!!
Last edited by herkow on Thu Oct 28, 2021 15:51; edited 1 time in total
Netgear WNDR3700 V4
DD-WRT v3.0-r47608 std (10/28/21)
Linux 3.18.140-d6 #129266 Thu Oct 28 16:54:14 +07 2021 mips
GUI install over r47596
uptime 2:45
radios, ovpn server, all good but ---
SAMBA still borked on this build same as last several
https://svn.dd-wrt.com/ticket/7486#comment:10
Joined: 16 Nov 2015 Posts: 6440 Location: UK, London, just across the river..
Posted: Thu Oct 28, 2021 20:34 Post subject:
Router Model TP-Link WR1043ND V2
Firmware Version DD-WRT v3.0-r47608 std (10/28/21)
Kernel Version Linux 3.18.140-d6 #129238 Thu Oct 28 15:59:36 +07 2021 mips
update: CLI r47528 > r47608
reset: NO
mode: Gateway
status: Operational 2h+
errors: Nothing new, yet.... bootloop after update (with no reset) problems resolved, unit is fully operation, so far so good, big thanks BS ...!! https://svn.dd-wrt.com/changeset/47597
Now speaking of improvements...since few builds backwards, lets say from a bit of a time...on save & apply router restarts: start up, firewall, custom script and shut down script...
Is there any chance to exclude shutdown script from those process restart...or delay start up script, so after execution of all the rest, start up script will run at last, so all the services will be rebooted...
The issue is, i have some shut down rules and i have always manually restart those services on any save & apply ...
I know i can use only save button and wait till the next reboot, but..its not that functional, and i tend to not reboot my router unless in not really needed...
Thanks in advance... _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55630 WAP
TP-Link WR1043NDv2 -DD-WRT 55723 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55779 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55819 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55779 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
Last edited by Alozaros on Fri Oct 29, 2021 9:41; edited 1 time in total
Joined: 08 May 2018 Posts: 14223 Location: Texas, USA
Posted: Thu Oct 28, 2021 21:26 Post subject:
Apparently the kernel backports that got reverted either affected kernel size or were askew somehow. Good to know things are good now, but I intend to follow-up on this. Thanks for the report!
Upgraded: DD-WRT v3.0-r47377 std (09/07/21)
Reset: No not this time
Status: Up and running for 4 hours, basic setup as Gateway, static leases, 2.4 GHz and 5 GHz working (vanilla firmware), OpenVPN server working, WireGuard Server working.
Router/Version: Netgear R7800
File: dd-wrt-webupgrade.bin
Firmware: DD-WRT v3.0-r47608 std (10/28/21) (prev. DD-WRT v3.0-r47581 std (10/20/21))
Kernel: Linux 4.9.287 #527 SMP Thu Oct 28 11:54:26 +07 2021 armv7l
Mode: Gateway, SFE disabled, 2.4G and 5G wifi, Wireguard for external access, WAN to 4G, Keep Alive reboot 6:02 in the morning
Reset: No
Status: Ok. Installed it two days ago.
Router Model / Version: Netgear XR500
Previous Firmware: Stock
Current Firmware: DD-WRT v3.0-r47608 std (10/28/21)
File:: factory-to-ddwrt.img
Kernel: Linux 4.9.287 #527 SMP Thu Oct 28 11:54:26 +07 2021 armv7l
Reset: No
Wireless: Disabled
Routing: Operating - Gateway
Setup: Default
Services: Default
Administration: Default
Uptime: up 2:27, load average: 0.00, 0.00, 0.00
Temperature: CPU 51.123 °C
Status: OK
Issues: See Below
1.) Just noticed that every time I do a reset using the GUI or Shell the swconfig tab disappears. It only shows up when I install a new firmware without resetting. This happens on this build and the last few firmware's that I tested dating back to the May build.
2.) I also lose access to the router (shell and GUI) when I try to add VLANS after a clean install. As soon as I add a VLAN and hit apply, I lose access to the router. I need to reset the router in order to access it again.
3.) Guid Vlan config doesn't match the config from console. Related to issue #2 ??
Code:
root@DD-WRT:~# swconfig dev switch0 show
Global attributes:
enable_vlan: 0
enable_mirror_rx: 0
enable_mirror_tx: 0
mirror_monitor_port: 0
mirror_source_port: 0
disable_all_leds: ???
arl_age_time: 300
arl_table: address resolution table
Port 0: MAC XX:XX:XX:XX:XX:XX
Port 1: MAC XX:XX:XX:XX:XX:XX
Port 6: MAC XX:XX:XX:XX:XX:XX