Posted: Thu Jul 08, 2021 7:28 Post subject: New Build - 07/08/2021 - r47033
[WARNING]: This thread is only for feedback on this beta release for developers and the community's benefit.
DO NOT flash this beta release unless you understand the risks involved and device specificrecovery methods.
Avoid discussions! Create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues:
• Show us your findings with steps to reproduce, configuration, output, logs and important information below!
Important:
• For issues provide applicable info: 'dmesg', 'cat /tmp/var/log/messages', syslog, klog, serial, strace, tcpdump, wireshark etc.
• Any firewall NAT or WAN issues, show output: 'iptables -vnL', 'iptables -t nat -vnL', 'iptables -t mangle -vnL' and /tmp/.ipt file.
• Search SVN tickets & discuss in forum before opening. Before reporting: reset & manually set up, not restore from a backup.
• Please include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) & relevant configuration information.
Linksys EA8500
DD-WRT v3.0-r47033 std (07/08/21)
Linux 4.9.274 #315 SMP Wed Jul 7 03:22:04 +07 2021 armv7l
GUI install over r47000
switch / ovpn server / VLAN on two ports / samba share x2 -- 32 GB ext4 + 16GB ext4
#
Netgear WNDR3700 V4
DD-WRT v3.0-r47033 std (07/08/21)
Linux 3.18.140-d6 #120613 Thu Jul 8 08:28:47 +07 2021 mips
GUI install over r47000 ...would NOT upgrade till I cleared dumbass Chrome's cache then all good
switch / ovpn server
#
Linksys EA8500...main router
DD-WRT v3.0-r47033 std (07/08/21)
Linux 4.9.274 #315 SMP Wed Jul 7 03:22:04 +07 2021 armv7l
GUI install over r47000
ovpn server / VLAN on one port + wlan0.1 via br1 / samba share 32 GB ext4
Stupid thing showed correct WAN IP + local DNS all good but could NOT access my public webserver or anything the on WAN.
Done a simple reboot thru the webif and she is all very good after that.
------
all 3 units worky very nice ... after the reboot of main
ovpn servers all good tested using Moto Edge plus w/openVPN for android
AND
I have OVPN on this Debian 'Bullseve' laptop still connected to the WNDR3700V4 ovpn server writting/posting all this...
...using the Moto Edge plus as hotspot. too bad out around my homeworld can only get 4G Verizon network and its not very good.
although in/around any decent sized town the Moto Edge plus will connect to Verizon's 5G wideband network and that is really nice
Joined: 08 May 2018 Posts: 14246 Location: Texas, USA
Posted: Thu Jul 08, 2021 14:04 Post subject:
Router Model & Version: TP-Link TL-WA901ND v2
Firmware: DD-WRT v3.0-r47032 std (07/07/21)
File: tl-wa901ndv2-webflash.bin
Kernel: Linux 3.10.108-d11 #85417 Wed Jul 7 02:20:51 +07 2021 mips
Previous: 20548
Reset: No
Mode: AP
Uptime: ~24hrs
Status: Ok
Issues/Errors: None. This release fixes an issue since 2013 where you had to flash 20675+ then revert to 20458 to have a working WAN/ethernet port on this AP. _________________ "Life is but a fleeting moment, a vapor that vanishes quickly; All is vanity"
Contribute To DD-WRT Pogo - A minimal level of ability is expected and needed... DD-WRT Releases 2023 (PolitePol)
DD-WRT Releases 2023 (RSS Everything)
----------------------
Linux User #377467 counter.li.org / linuxcounter.net
Status: Working Fine except Samba; running vanilla firmware type for 2.4ghz & DD-wrt for 5ghz, uptime 30 min
Samba share not accessible, following errors in syslog
Jul 8 17:13:17 R7800 local5.err ksmbd: [ksmbd-manager/2696]: ERROR: Can't open `/tmp/ksmbd.subauth': No such file or directory
>> this file exists in the folder, this error appears only once then get following log
update: via CLI
status: Operational 12h +
reset: NO
errors: will report later in a day....on previous builds WiFi was a nightmare with some devices...still waiting to see 47033 if its more stable ...will report tomorrow _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55630 WAP
TP-Link WR1043NDv2 -DD-WRT 55723 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55779 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55819 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55779 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
Joined: 19 Nov 2008 Posts: 274 Location: Madison, CT, US
Posted: Fri Jul 09, 2021 15:48 Post subject:
Routers: Netgear r7800 and r7500v2
Firmware: DD-WRT r47033 from r46974
Reset: No
Used a WDS system. Working fine so far.
ddwrt drivers for wifi
NAS Truenas operational
USB could not install with r46974 so have not tried on r47033. Mounted but had trouble with FS ntfs and extfat. Do not want fat32.
Wireguard operational.
Thank you BS. Really appreciate the work you and your team provide. _________________ Netgear R7800(2), R7500v2(2) WDS, Asus RT-AC68R (2)
As mentioned in the previous build (r47000), every time I do a reset using the GUI or Shell the swconfig tab disappears. It only shows up when I install a new firmware without resetting. This happens on this build and the last few firmware's that I tested dating back to the May build. This also happens on my Netgear XR500.
I also lose access to the router (shell and GUI) when I try to add VLANS after a reset. As soon as I add a VLAN and hit apply, I lose access to the router. I need to reset the router in order to access it again. Perhaps it has something to do with the GUI showing lan ports on VLAN0 while in the CLI lan ports are on VLAN1. See attached picture.
Posted: Sat Jul 10, 2021 14:55 Post subject: Netgear R7800 wifi
Router/Version: Netgear R7800
File/Kernel: 47033
Previous/Reset: 47000, not reset
Mode/Status: WDS AP, QoS
Issues/Errors: Wifi not working on some clients. Some clients connect, others don't. Didn't modify Wifi settings between versions at all. Inplace downgrade to 47000 fixed the Wifi issue.
Posted: Sat Jul 10, 2021 15:20 Post subject: Re: Netgear R7800 wifi
ian5142 wrote:
Router/Version: Netgear R7800
File/Kernel: 47033
Previous/Reset: 47000, not reset
Mode/Status: WDS AP, QoS
Issues/Errors: Wifi not working on some clients. Some clients connect, others don't. Didn't modify Wifi settings between versions at all. Inplace downgrade to 47000 fixed the Wifi issue.
