Hello! Need suport for new board wr749n v6 .

Post new topic   Reply to topic    DD-WRT Forum Index -> Atheros WiSOC based Hardware
Author Message
braza
DD-WRT User


Joined: 09 Oct 2006
Posts: 112

PostPosted: Wed Aug 24, 2016 18:53    Post subject: Hello! Need suport for new board wr749n v6 . Reply with quote
Hi.
I have removed the SPI and manual flashed the dd-wrt to my new router wr749n v6 .

I have inserted wr841n v10.

The only POWER LED not worked .

DMESG log.

<5>[ 0.000000] Linux version 3.18.38 (root@nmndev) (gcc version 6.1.0 (LEDE GCC 6.1.0 r1259) ) #1475 Tue Aug 16 05:30:46 CEST 2016
<6>[ 0.000000] bootconsole [early0] enabled
<6>[ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
<4>[ 0.000000] cpu apb ddr apb cpu 650 ddr 390 ahb 216
<6>[ 0.000000] sys id = 160 Qualcomm Atheros QCA9533 ver 2 rev 1.0 (0x0160)
<6>[ 0.000000] Determined physical RAM map:
<6>[ 0.000000] memory: 02000000 @ 00000000 (usable)
<4>[ 0.000000] Zone ranges:
<4>[ 0.000000] Normal [mem 0x00000000-0x01ffffff]
<4>[ 0.000000] Movable zone start for each node
<4>[ 0.000000] Early memory node ranges
<4>[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
<6>[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x01ffffff]
<7>[ 0.000000] On node 0 totalpages: 8192
<7>[ 0.000000] free_area_init_node: node 0, pgdat 802dc2f0, node_mem_map 81000000
<7>[ 0.000000] Normal zone: 64 pages used for memmap
<7>[ 0.000000] Normal zone: 0 pages reserved
<7>[ 0.000000] Normal zone: 8192 pages, LIFO batch:0
<4>[ 0.000000] Primary instruction cache 64kB, 4-way, VIPT, I-cache aliases, linesize 32 bytes.
<4>[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
<7>[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
<7>[ 0.000000] pcpu-alloc: [0] 0
<4>[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
<5>[ 0.000000] Kernel command line: console=ttyS0,115200 root=1f02 rootfstype=squashfs noinitrd init=/sbin/init
<6>[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
<6>[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
<6>[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
<6>[ 0.000000] Writing ErrCtl register=00000000
<6>[ 0.000000] Readback ErrCtl register=00000000
<4>[ 0.000000] Memory: 28996K/32768K available (2278K kernel code, 151K rwdata, 200K rodata, 176K init, 240K bss, 3772K reserved)
<6>[ 0.000000] NR_IRQS:83
<6>[ 0.060000] Calibrating delay loop... 432.53 BogoMIPS (lpj=2162688)
<6>[ 0.060000] pid_max: default: 32768 minimum: 301
<6>[ 0.060000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
<6>[ 0.070000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
<6>[ 0.070000] NET: Registered protocol family 16
<6>[ 0.500000] Switched to clocksource MIPS
<6>[ 0.500000] NET: Registered protocol family 2
<6>[ 0.510000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
<6>[ 0.510000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
<6>[ 0.520000] TCP: Hash tables configured (established 1024 bind 1024)
<6>[ 0.520000] TCP: reno registered
<6>[ 0.530000] UDP hash table entries: 256 (order: 0, 4096 bytes)
<6>[ 0.530000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
<6>[ 0.540000] NET: Registered protocol family 1
<7>[ 0.540000] PCI: CLS 0 bytes, default 32
<5>[ 0.540000] gpio_proc: module loaded and /proc/gpio/ created
<5>[ 0.550000] wl0gpio_proc: module loaded and /proc/wl0gpio/ created
<6>[ 0.560000] futex hash table entries: 256 (order: -1, 3072 bytes)
<6>[ 0.570000] squashfs: version 3.0 (2006/03/15) Phillip Lougher
<6>[ 0.570000] msgmni has been set to 56
<6>[ 0.580000] io scheduler noop registered (default)
<6>[ 0.580000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
<6>[ 0.590000] console [ttyS0] disabled
<6>[ 0.610000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A
<6>[ 0.620000] console [ttyS0] enabled
<6>[ 0.630000] bootconsole [early0] disabled
<0>[ 0.630000] guessed flashsize = 4M
<0>[ 0.640000] scanning for root partition
<0>[ 0.640000] tplink uboot detected
<0>[ 0.650000] guessed bootloader size = 20000
<0>[ 0.660000]
<0>[ 0.660000] found squashfs at 110000
<6>[ 0.670000] adjusted length 3E0000, original length 3DB8C6
<5>[ 0.670000] Creating 9 MTD partitions on "ar7240-nor0":
<5>[ 0.680000] 0x000000000000-0x000000020000 : "RedBoot"
<5>[ 0.680000] 0x000000020000-0x0000003e0000 : "linux"
<5>[ 0.690000] 0x000000110000-0x0000003e0000 : "rootfs"
<5>[ 0.690000] mtd: partition "rootfs" set to be root filesystem
<5>[ 0.700000] 0x0000003e0000-0x000000400000 : "ddwrt"
<5>[ 0.710000] 0x0000003e0000-0x0000003f0000 : "nvram"
<5>[ 0.710000] 0x0000003f0000-0x000000400000 : "board_config"
<5>[ 0.720000] 0x000000000000-0x000000400000 : "fullflash"
<5>[ 0.720000] 0x000000000000-0x000000020000 : "fullboot"
<5>[ 0.730000] 0x000000010000-0x000000020000 : "uboot-env"
<6>[ 0.740000] libphy: Fixed MDIO Bus: probed
<6>[ 0.740000] tun: Universal TUN/TAP device driver, 1.6
<6>[ 0.750000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
<6>[ 0.750000] PPP generic driver version 2.4.2
<6>[ 0.760000] PPP BSD Compression module registered
<6>[ 0.760000] PPP Deflate Compression module registered
<6>[ 0.770000] PPP MPPE Compression module registered
<6>[ 0.770000] NET: Registered protocol family 24
<6>[ 0.780000] u32 classifier
<6>[ 0.790000] Performance counters on
<6>[ 0.790000] input device check on
<6>[ 0.790000] Actions configured
<6>[ 0.800000] Netfilter messages via NETLINK v0.30.
<6>[ 0.800000] nf_conntrack version 0.5.0 (453 buckets, 1812 max)
<4>[ 0.810000] nf_conntrack_rtsp v0.7 loading
<4>[ 0.810000] nf_nat_rtsp v0.7 loading
<6>[ 0.820000] ip_tables: (C) 2000-2006 Netfilter Core Team
<6>[ 0.820000] TCP: westwood registered
<6>[ 0.830000] TCP: hybla registered
<6>[ 0.830000] TCP: vegas registered
<6>[ 0.830000] NET: Registered protocol family 17
<6>[ 0.840000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
<5>[ 0.850000] Bridge firewalling registered
<6>[ 0.860000] 8021q: 802.1Q VLAN Support v1.8
<6>[ 0.860000] searching for nvram
<6>[ 0.860000] nvram size = 0
<6>[ 0.900000] Atheros AR71xx hardware watchdog driver version 0.1.0
<6>[ 0.900000] ar71xx-wdt: timeout=15 secs (max=171) ref freq=25000000
<6>[ 0.930000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
<6>[ 0.940000] Freeing unused kernel memory: 176K (802f4000 - 80320000)
<7>[ 3.080000] ar71xx-wdt: enabling watchdog timer
<6>[ 3.180000] libphy: ag71xx_mdio: probed
<6>[ 3.770000] ag71xx-mdio.1: Found an AR934X built-in switch
<6>[ 3.830000] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
<6>[ 4.500000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042, driver=Generic PHY]
<6>[ 4.510000] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
<6>[ 4.790000] Loading modules backported from Linux version wt-2016-06-20-0-gbc17424
<6>[ 4.800000] Backport generated by backports.git backports-20160216-7-g5735958
<7>[ 5.560000] ath: EEPROM regdomain: 0x0
<7>[ 5.560000] ath: EEPROM indicates default country code should be used
<7>[ 5.560000] ath: doing EEPROM country->regdmn map search
<7>[ 5.560000] ath: country maps to regdmn code: 0x3a
<7>[ 5.560000] ath: Country alpha2 being used: US
<7>[ 5.560000] ath: Regpair used: 0x3a
<7>[ 5.570000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
<6>[ 5.580000] ieee80211 phy0: Atheros AR9531 Rev:2 mem=0xb8100000, irq=79
<6>[ 6.180000] eth0: link up (1000Mbps/Full duplex)
<6>[ 7.490000] device br0 entered promiscuous mode
<6>[ 7.520000] eth0: link down
<6>[ 7.690000] device eth0 entered promiscuous mode
<6>[ 7.700000] br0: port 1(eth0) entered forwarding state
<6>[ 7.710000] br0: port 1(eth0) entered forwarding state
<6>[ 7.710000] device br0 left promiscuous mode
<6>[ 7.720000] device br0 entered promiscuous mode
<6>[ 7.740000] device br0 left promiscuous mode
<6>[ 8.490000] br0: port 1(eth0) entered disabled state
<6>[ 9.290000] eth0: link up (1000Mbps/Full duplex)
<6>[ 9.290000] br0: port 1(eth0) entered forwarding state
<6>[ 9.300000] br0: port 1(eth0) entered forwarding state
<6>[ 11.300000] br0: port 1(eth0) entered forwarding state
<6>[ 12.980000] nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead.
<6>[ 15.190000] device ath0 entered promiscuous mode
<6>[ 15.190000] br0: port 2(ath0) entered forwarding state
<6>[ 15.200000] br0: port 2(ath0) entered forwarding state
<5>[ 15.830000] random: dropbearkey urandom read with 31 bits of entropy available
<6>[ 15.850000] device eth1 entered promiscuous mode
<6>[ 17.040000] device eth1 left promiscuous mode
<6>[ 17.200000] br0: port 2(ath0) entered forwarding state
<5>[ 41.710000] random: nonblocking pool is initialized
<6>[ 145.600000] device eth0 left promiscuous mode
<6>[ 145.610000] br0: port 1(eth0) entered disabled state
<6>[ 145.620000] device ath0 left promiscuous mode
<6>[ 145.630000] br0: port 2(ath0) entered disabled state
<6>[ 145.880000] device br0 entered promiscuous mode
<6>[ 145.920000] eth0: link down
<6>[ 146.090000] device eth0 entered promiscuous mode
<6>[ 146.100000] br0: port 1(eth0) entered forwarding state
<6>[ 146.100000] br0: port 1(eth0) entered forwarding state
<6>[ 146.120000] device br0 left promiscuous mode
<6>[ 146.130000] device br0 entered promiscuous mode
<6>[ 146.150000] device br0 left promiscuous mode
<6>[ 146.630000] br0: port 1(eth0) entered disabled state
<6>[ 147.710000] eth0: link up (1000Mbps/Full duplex)
<6>[ 147.710000] br0: port 1(eth0) entered forwarding state
<6>[ 147.720000] br0: port 1(eth0) entered forwarding state
<6>[ 149.720000] br0: port 1(eth0) entered forwarding state
<6>[ 153.850000] device ath0 entered promiscuous mode
<6>[ 153.860000] br0: port 2(ath0) entered forwarding state
<6>[ 153.860000] br0: port 2(ath0) entered forwarding state
<6>[ 155.860000] br0: port 2(ath0) entered forwarding state

_________________
Sponsor
legolas
DD-WRT Novice


Joined: 22 Feb 2017
Posts: 26

PostPosted: Wed Jun 23, 2021 16:29    Post subject: Reply with quote
Hello, found any solution on this?
_________________
In use, community ISP:
1 tplink WR842ND; 2 WR741N; 3 WR740N : with DD-WRT
1 mymax WR934-BK "original" firmware
1 d-link dsl-2740e with Totolink ND300
2 Sagem F@ST2704 with OpenWrt
1 wavlink ND300
1 wrt54g
waiting:
1 wrt54g
airgrid m5 bullet
kernel-panic69
DD-WRT Guru


Joined: 08 May 2018
Posts: 14126
Location: Texas, USA

PostPosted: Wed Jun 23, 2021 18:01    Post subject: Reply with quote

  1. Please provide a better internal photo of SoC
  2. I have found no information on a TL-WR749N v6 except:
    https://usermanual.wiki/Tp-Link/TlWr749NV6Ug.1033871736/view
  3. I have only found information on a TL-WR740N v6:

    1. https://wikidevi.wi-cat.ru/TP-LINK_TL-WR740N_v6.x
    2. https://fccid.io/TE7WR940NV6
    3. https://openwrt.org/toh/tp-link/tl-wr740n
    4. https://www.tp-link.com/us/support/download/tl-wr740n/#Firmware

If the TL-WR841Nv10 is similar (or if it would be better to use the TL-WR740Nv5 image), that's the only "solution" I can think of because I see no definite information in the header or anywhere in any firmware images that delineate the router model as with other TP-Link devices.

_________________
"Life is but a fleeting moment, a vapor that vanishes quickly; All is vanity"
Contribute To DD-WRT
Pogo - A minimal level of ability is expected and needed...
DD-WRT Releases 2023 (PolitePol)
DD-WRT Releases 2023 (RSS Everything)

----------------------
Linux User #377467 counter.li.org / linuxcounter.net
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Index -> Atheros WiSOC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum