New Build - 06/18/2021 - r46974

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware
Goto page Previous  1, 2
Author Message
egc
DD-WRT Guru


Joined: 18 Mar 2014
Posts: 8184
Location: Netherlands

PostPosted: Sat Jun 19, 2021 16:51    Post subject: Reply with quote
Router Model: Netgear R6400v1

Firmware Version: DD-WRT v3.0-r46974M Community Build (06/18/21)
Kernel Version: Linux 4.4.272 #1 SMP Sun Jun 13 08:43:06 CEST 2021 armv7l

Upgraded from: DD-WRT v3.0-r46949M Community Build (06/13/21)
Reset: No not this time

Status: Up and running for 24 hours, basic setup as Gateway, static leases, Advanced routing, Port Forwarding, IPv4, 2.4 GHz and 5 GHz.
Running one WireGuard tunnel to Keepsolid and second WireGuard tunnel to own WG server for site-to-site connection.
OpenVPN client tested and working

Errors: None

Big Thanks to BS and other forum members and developers.

_________________
Routers:Netgear R7800, R6400v1, R6400v2, Linksys EA8500, EA6900 (XvortexCFE), E2000 (converted WRT320N), WRT54GS v1.
WireGuard Documents & Guides:https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=327397
OpenVPN Documents & Guides: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=327398
IPSET: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=327261
Install guide R6400v2:http://forum.dd-wrt.com/phpBB2/viewtopic.php?t=316399
Install guide R7800: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=320614
Forum Guide Lines (important read):https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=324087
Sponsor
thommy181
DD-WRT User


Joined: 16 Mar 2019
Posts: 223
Location: Szczecin, Poland EU

PostPosted: Sat Jun 19, 2021 18:09    Post subject: New Build - 06/18/2021 - r46974 Reply with quote
Router/Version: Netgear WNR3500L v2
Status: Totally can't boot
Errors: Can't boot after flash via ssh

The Netgear WNR3500L v2 can't boot on any version newer than 6/10/2021. Router stay on begin and totally won't to start. Probably it not depend of nvram data. When I can't start router I'm restore it via button on case. Device can't start still. Developpers erased build from 6/13/2021 from server. That was last good build for low end routers like Netgear based on MIPS. Actually I must stay with 6/10/21 build and router is usable.
I'm dump start procedure when is boot problem.
Quote:

Decompressing...done

CFE for WNR3500Lv2 version: v1.0.9
Build Date: Fri May 6 11:54:17 CST 2011
Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
NFLASH Boot partition size = 524288(0x80000)
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.60.136
CPU type 0x19749: 480MHz
Tot mem: 131072 KBytes

Device eth0: hwaddr XXX, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
Checking crc...done.
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: ........ 4429432 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000

Then device do nothing, it's only orange power led lighting.
Pdobrien3
DD-WRT User


Joined: 12 Dec 2015
Posts: 135

PostPosted: Sun Jun 20, 2021 23:56    Post subject: Reply with quote
Router/Version: Asus RT-AC68U H/W Version C1
Mode: WAP
File: DD-WRT v3.0-r46974 std (06/18/21)
Kernel: Linux 4.4.272 #3481 SMP Thu Jun 17 14:46:47 +07 2021 armv7l
Status:

Ok, I have been trying to transition from Firmware: DD-WRT v3.0-r46446 std (04/24/21) with two perfect guest VLANS. I have two other routers with similar setups. I was able to get the guest VLANS (14 and 15) working but when I try to connect to the main wireless interface for the home network, I cant get an IP on the trunk port (2). As soon as I switch to another port, main network works but of course the guest vlans dont. Playing all day and can't figure it out. Are VLANS supposed to be 100% working?
icimasayki
DD-WRT Novice


Joined: 18 Jun 2021
Posts: 2

PostPosted: Mon Jun 21, 2021 2:11    Post subject: Reply with quote
Router/Version: Buffalo WZR-1750DHP
File/Kernel: buffalo-wzr-1750dhp-webflash.bin/Linux 4.4.272 #3481 SMP Thu Jun 17 14:46:47 +07 2021 armv7l
Previous/Reset: 46958/No
Mode/Status: AP, Repeater Bridge, and AP with WDS
Issues/Errors: WDS works only withtout wifi encription

I tried three modes and all worked fine. The performance of WDS is absolutely what I dreamed, so I am looking forward to the day when we can use WDS with WPA2.
kernel-panic69
DD-WRT Guru


Joined: 08 May 2018
Posts: 10195
Location: Texas, USA

PostPosted: Mon Jun 21, 2021 2:38    Post subject: Reply with quote
Maybe the OP didn't quite get fully read:

WDS does not work on Broadcom ARM devices (only MIPS<->MIPS)

https://wikidevi.wi-cat.ru/Buffalo_WZR-1750DHP

https://www.broadcom.com/products/wireless/wireless-lan-infrastructure/bcm4707-4708-4709

_________________
Official Forum Rules, Guidelines & Helpful InformationFirmware FAQInstallation WikiWhere Do I Download Firmware‽
DON'T use Chromium-based browsersRTFM/STFW TL;DR is NOT an excuse. • Why Should I Care What Color the Bikeshed Is‽
Please DO NOT PM me with questions; Ask in the forum. ---------------------- Linux User #377467 counter.li.org / linuxcounter.net
Groundnet
DD-WRT Novice


Joined: 23 Nov 2018
Posts: 4

PostPosted: Mon Jun 21, 2021 19:09    Post subject: Reply with quote
Router/Version: Netgear WNDR3700v3
File: dd-wrt.v24-46974_NEWD-2_K3.x_mega-nv64k.bin
Previous/Reset: 46854 / No reset
Mode/Status: Gateway
Issues/Errors: Fails to get IP from ISP

Wrestled with it for 30 minutes then after running out of swear words reverted to 46854.
Of the things I tried in between swearing the update changed the MAC I had set on the WAN side and if memory serves it was the same MAC as the LAN side, but resetting the wan MAC to what I had recorded had no effect.

Ran out of time reverted the version and restored the config and everything is working again. Will try another version in the future.
Pdobrien3
DD-WRT User


Joined: 12 Dec 2015
Posts: 135

PostPosted: Tue Jun 22, 2021 23:40    Post subject: Reply with quote
Pdobrien3 wrote:
Router/Version: Asus RT-AC68U H/W Version C1
Mode: WAP
File: DD-WRT v3.0-r46974 std (06/18/21)
Kernel: Linux 4.4.272 #3481 SMP Thu Jun 17 14:46:47 +07 2021 armv7l
Status:

Ok, I have been trying to transition from Firmware: DD-WRT v3.0-r46446 std (04/24/21) with two perfect guest VLANS. I have two other routers with similar setups. I was able to get the guest VLANS (14 and 15) working but when I try to connect to the main wireless interface for the home network, I cant get an IP on the trunk port (2). As soon as I switch to another port, main network works but of course the guest vlans dont. Playing all day and can't figure it out. Are VLANS supposed to be 100% working?


So I did a little more digging tonight. Since I couldn't pull an IP wirelessly on the main network, I decided to go back to factory settings and see what would happen. I couldnt pull an IP on the default dd-wrt wireless interface with DHCP turned on.
kernel-panic69
DD-WRT Guru


Joined: 08 May 2018
Posts: 10195
Location: Texas, USA

PostPosted: Wed Jun 23, 2021 0:44    Post subject: Reply with quote
If you had any custom nvram set variables, you must wipe out nvram completely via nvram erase or mtd erase nvram.
_________________
Official Forum Rules, Guidelines & Helpful InformationFirmware FAQInstallation WikiWhere Do I Download Firmware‽
DON'T use Chromium-based browsersRTFM/STFW TL;DR is NOT an excuse. • Why Should I Care What Color the Bikeshed Is‽
Please DO NOT PM me with questions; Ask in the forum. ---------------------- Linux User #377467 counter.li.org / linuxcounter.net
Pdobrien3
DD-WRT User


Joined: 12 Dec 2015
Posts: 135

PostPosted: Wed Jun 23, 2021 0:52    Post subject: Reply with quote
kernel-panic69 wrote:
If you had any custom nvram set variables, you must wipe out nvram completely via nvram erase or mtd erase nvram.


Sorry, I did an nvram erase prior to......still no dhcp.
Goto page Previous  1, 2 Display posts from previous:    Page 2 of 2
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum