New Build - 05/30/2021 - r46816

Post new topic   Reply to topic    DD-WRT Forum Index -> Broadcom SoC based Hardware
Goto page Previous  1, 2
Author Message
BrainSlayer
Site Admin


Joined: 06 Jun 2006
Posts: 7463
Location: Dresden, Germany

PostPosted: Mon May 31, 2021 5:21    Post subject: Re: Asus RT-AC87U Reply with quote
kooper2013 wrote:
Router/Version: Asus RT-AC87U
File/Kernel: asus_rt-ac87u-firmware.trx
Previous/Reset: r46733
Mode/Status: WAP, wg-client, 2.4+5G, DHCP server, SFE on, no fancy config
Issues/Errors: unusable

Unusable for me.
First no GUI access (via LAN), but wg and internet OK. 3 times off/on, then ssh-access and GUI for some time. Took LOGs, see attachment.
wifi: SSIDs were sent, but no device could connect. Access lost entirely after F5 on tab Tunnels.
Reset by button, restored previous config, same issue.

Back to r46733.


according to your log, your wan port is disabled or your 2.4 wifi interface is in client mode. everything else seem to work.

_________________
"So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
Sponsor
BrainSlayer
Site Admin


Joined: 06 Jun 2006
Posts: 7463
Location: Dresden, Germany

PostPosted: Mon May 31, 2021 5:26    Post subject: Reply with quote
turbowells wrote:
Router/Version: Asus RT-N12D
File: dd-wrt.v24-#####_NEWD-2_K3.x_mega.bin
Firmware: DD-WRT v3.0-r46816 mega (05/30/21)
Kernel: Linux 4.4.269 #9704 Sun May 30 06:37:47 +07 2021 mips
Mode: Default settings
Previous: r46442
Reset?: Y
Status: Not working, no WAN IP assigned. Last working version is r46442. Did a few "nvram clear && reboots".

Code:

root@DD-WRT:~# nvram show | grep vlan.*ports | sort
vlan0ports=3 2 1 0 5*
vlan1ports=4 5

root@DD-WRT:~# nvram show | grep port.*vlans | sort
port0vlans=2
port1vlans=1
port2vlans=1
port3vlans=1
port4vlans=1
port5vlans=1 2 16000

root@DD-WRT:~# nvram show | grep vlan.*hwname | sort
vlan0hwname=et0
vlan1hwname=et0

root@DD-WRT:~# nvram show | grep vlan0 | sort
lan_ifnames=vlan0 eth1 eth2 eth3
vlan0_bridged=1
vlan0hwname=et0
vlan0ports=3 2 1 0 5*

root@DD-WRT:~# nvram show | grep vlan1 | sort
pppoe_ifname=vlan1
pppoe_wan_ifname=vlan1
vlan1_hwaddr=B0:6E:BF:77:94:70
vlan1hwname=et0
vlan1ports=4 5
wan_default=vlan1
wan_ifname2=vlan1
wan_ifname=vlan1
wan_ifnames=vlan1


the provided information does not help. too much is missing. swconfig dev switch0 show output for instance.

_________________
"So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
BrainSlayer
Site Admin


Joined: 06 Jun 2006
Posts: 7463
Location: Dresden, Germany

PostPosted: Mon May 31, 2021 7:05    Post subject: Reply with quote
turbowells wrote:
Router/Version: Asus RT-N12D
File: dd-wrt.v24-#####_NEWD-2_K3.x_mega.bin
Firmware: DD-WRT v3.0-r46816 mega (05/30/21)
Kernel: Linux 4.4.269 #9704 Sun May 30 06:37:47 +07 2021 mips
Mode: Default settings
Previous: r46442
Reset?: Y
Status: Not working, no WAN IP assigned. Last working version is r46442. Did a few "nvram clear && reboots".

Code:

root@DD-WRT:~# nvram show | grep vlan.*ports | sort
vlan0ports=3 2 1 0 5*
vlan1ports=4 5

root@DD-WRT:~# nvram show | grep port.*vlans | sort
port0vlans=2
port1vlans=1
port2vlans=1
port3vlans=1
port4vlans=1
port5vlans=1 2 16000

root@DD-WRT:~# nvram show | grep vlan.*hwname | sort
vlan0hwname=et0
vlan1hwname=et0

root@DD-WRT:~# nvram show | grep vlan0 | sort
lan_ifnames=vlan0 eth1 eth2 eth3
vlan0_bridged=1
vlan0hwname=et0
vlan0ports=3 2 1 0 5*

root@DD-WRT:~# nvram show | grep vlan1 | sort
pppoe_ifname=vlan1
pppoe_wan_ifname=vlan1
vlan1_hwaddr=B0:6E:BF:77:94:70
vlan1hwname=et0
vlan1ports=4 5
wan_default=vlan1
wan_ifname2=vlan1
wan_ifname=vlan1
wan_ifnames=vlan1


i tested now a RT-N12D, but found no issues. all is working as expected. will now just try if wan is working.

edit:
found the wan port problem and fixed it

_________________
"So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
lfb
DD-WRT Novice


Joined: 13 Nov 2016
Posts: 16

PostPosted: Mon May 31, 2021 9:18    Post subject: Reply with quote
Router/Version: Buffalo WZR1750DHP
File/Kernel: 46816
Previous/Reset: 45735 / No
Mode/Status: 2G Client bridge, 5G AP, no WAN
Issues/Errors: Switch dead

Dead switch, for a very short time pingeable (less than a minute, web interface starting but never readable). WLAN working as long as one doesn't connect the router via cable. Same behaviour for 46788, working again on 46750.

Linksys EA6900 is working in 46788 though, different setup (2G AP, WAN via WAN port), but firmware images are identical to Buffalo WZR21750.
chuhuanping
DD-WRT Novice


Joined: 10 Sep 2010
Posts: 1

PostPosted: Mon May 31, 2021 14:09    Post subject: Reply with quote
Router/Version: WZR-1750DHP2
Firmware: DD-WRT v3.0-r46816 std (05/30/21)
Kernel: Linux 4.4.269 #3242 SMP Sun May 30 03:22:26 +07 2021 armv7l
Mode: Router, PPPOE ,Wireless AP. CTF Enabled. NAT ON and QOS Off.
Reset: Nope.
Status: Whenever I turn on the bittorrent clients like Bitcomet V1.77, it crashes PPPoE connection everytime and stops the entire WAN connection.
It’s ok as I switch to SFE mode.
dpp3530
DD-WRT Guru


Joined: 12 Dec 2007
Posts: 761
Location: Pittsburgh, PA USA

PostPosted: Mon May 31, 2021 14:19    Post subject: Reply with quote
Updated two Netgear AC1450s and a Linksys EA6700 from 46788. All are being used as wired access points (WAN disabled, DHCP server disabled). I just did an update, no reset.

After update, the routers booted up and pinged a few times, then stopped pinging. No GUI or SSH access. I was able to recover the EA6700 using TFTP. The Netgears required more drastic intervention (https://midnightme.com/2015/03/16/how-to-unbrick-or-fix-a-netgear-ac1450-router/). I'm back on 46788, restored config, and all are working now.

_________________
__________________________
Netgear R7800
DD-WRT v3.0 STD
Linksys WRT1900AC
DD-WRT v3.0 STD
BrainSlayer
Site Admin


Joined: 06 Jun 2006
Posts: 7463
Location: Dresden, Germany

PostPosted: Mon May 31, 2021 14:32    Post subject: Reply with quote
lfb wrote:
Router/Version: Buffalo WZR1750DHP
File/Kernel: 46816
Previous/Reset: 45735 / No
Mode/Status: 2G Client bridge, 5G AP, no WAN
Issues/Errors: Switch dead

Dead switch, for a very short time pingeable (less than a minute, web interface starting but never readable). WLAN working as long as one doesn't connect the router via cable. Same behaviour for 46788, working again on 46750.

Linksys EA6900 is working in 46788 though, different setup (2G AP, WAN via WAN port), but firmware images are identical to Buffalo WZR21750.


already fixed. enable wan as a workaround. this happens only if wan is disabled (or wifi is in client mode)

_________________
"So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
BrainSlayer
Site Admin


Joined: 06 Jun 2006
Posts: 7463
Location: Dresden, Germany

PostPosted: Mon May 31, 2021 14:34    Post subject: Reply with quote
dpp3530 wrote:
Updated two Netgear AC1450s and a Linksys EA6700 from 46788. All are being used as wired access points (WAN disabled, DHCP server disabled). I just did an update, no reset.

After update, the routers booted up and pinged a few times, then stopped pinging. No GUI or SSH access. I was able to recover the EA6700 using TFTP. The Netgears required more drastic intervention (https://midnightme.com/2015/03/16/how-to-unbrick-or-fix-a-netgear-ac1450-router/). I'm back on 46788, restored config, and all are working now.


same for you. enable wan. i fixed the issue already internally. fix will be released tomorrow since building takes a while

_________________
"So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
grmcdorman
DD-WRT Novice


Joined: 15 Oct 2017
Posts: 41

PostPosted: Mon May 31, 2021 17:04    Post subject: Reply with quote
Router/Version: Netgear Nighthawk R7000P
File/Kernel: netgear-r7000p-webflash.bin; Linux version 4.4.269 (root@linux) (gcc version 11.1.0 (OpenWrt GCC 11.1.0 r16592-aabc632023) ) #3202 SMP Fri May 28 02:56:10 +07 2021;
Firmware: DD-WRT v3.0-r46788 std (05/28/21)
Time: 13:03:46 up 1 day, 16:21, load average: 1.56, 1.55, 1.54
Previous/Reset: r46772, no reset
Mode/Status: Gateway (PPPoE)/2.4GHz & 5GHz AP/DHCP server/DNS Server/YaMON3/Samba

Also running syslog-ng and user-space NFSV3 via opkg.

Issues/Errors: Occasionally seeing this in the logs:
Code:

May 31 12:03:34 R7000P kernel: CONSOLE: 168178.085 wl0: Proxy STA [redacted]:79 link is already gone !!??
May 31 08:03:47 R7000P dnsmasq-dhcp[12433]: DHCPREQUEST(br0) [redacted].28 [redacted]:79
May 31 08:03:47 R7000P dnsmasq-dhcp[12433]: DHCPACK(br0) [redacted].28 [redacted]:79 nest-thermostat

Note the wl0 in the first message. The device, nest-thermostat, is on the 5GHz WiFi, wl1. (Timestamps are also odd, with the dnsmasp-dhcp getting timezone conversions applied twice - I'm in GMT-4 - but that's a long outstanding issue.)

However, this is the only hiccup; despite this everything seems to be running smoothly.

EDIT: Fixed hardware from "Nighthack" to "Nighthawk", although a Netgear Nighthack would be a unique device.
lfb
DD-WRT Novice


Joined: 13 Nov 2016
Posts: 16

PostPosted: Tue Jun 01, 2021 5:11    Post subject: Reply with quote
BrainSlayer wrote:
lfb wrote:
Router/Version: Buffalo WZR1750DHP
File/Kernel: 46816
Previous/Reset: 45735 / No
Mode/Status: 2G Client bridge, 5G AP, no WAN
Issues/Errors: Switch dead
......
already fixed. enable wan as a workaround. this happens only if wan is disabled (or wifi is in client mode)
Thanks!
thommy181
DD-WRT User


Joined: 16 Mar 2019
Posts: 353
Location: Szczecin, Poland EU

PostPosted: Tue Jun 01, 2021 10:25    Post subject: New Build - 05/30/2021 - r46816 Reply with quote
Router/Version: Netgear WNR3500L v2
Kernel: Linux 4.4.269 #9688 Sun May 30 06:19:46 +07 2021 mips
Reset: No
Mode: Internet gateway, WIFI AP, Dnsmasq server
Issues: WAN port work little better than earlier, I see vlan0 in switch config tab
Status: Working
Uptime: ~42 h

I'm update device via ssh. Router working rather good. WAN performance is little better than earlier. I have 280 - 290 mbit/s on internet speedometer. ISP serve me ~315 mbit (test on rj-45 cord without router). The WNR3500L v2 have all gigabit ports, but it's rather unavailable speed.
Goto page Previous  1, 2 Display posts from previous:    Page 2 of 2
Post new topic   Reply to topic    DD-WRT Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum