Posted: Fri May 28, 2021 9:56 Post subject: New Build - 05/28/2021 - r46788
[WARNING]: This thread is only for feedback on this beta release for developers and the community's benefit.
DO NOT flash this beta release unless you understand the risks involved and device specificrecovery methods.
Avoid discussions! Create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues:
• Show us your findings with steps to reproduce, configuration, output, logs and important information below!
Important:
• For issues provide applicable info: 'dmesg', 'cat /tmp/var/log/messages', syslog, klog, serial, strace, tcpdump, wireshark etc.
• Any firewall NAT or WAN issues, show output: 'iptables -vnL', 'iptables -t nat -vnL', 'iptables -t mangle -vnL' and /tmp/.ipt file.
• Search SVN tickets & discuss in forum before opening. Before reporting: reset & manually set up, not restore from a backup.
• Please include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) & relevant configuration information.
Netgear WNDR3700 V4
DD-WRT v3.0-r46788 std (05/28/21)
Linux 3.18.140-d6 #116992 Fri May 28 05:52:37 +07 2021 mips
GUI install over r46779
good
#
Linksys EA8500
DD-WRT v3.0-r46788 std (05/28/21)
Linux 4.9.269 #207 SMP Thu May 27 15:18:19 +07 2021 armv7l
good
main gateway router has:
DD-WRT v3.0-r46788 std (05/27/21)
Linux 4.9.269 #205 SMP Thu May 27 12:30:50 +07 2021 armv7l
she is worky great --- up 23:05 --- so I will leave her alone
---
EDIT: alright then ---
I put this on main gateway EA8500 cause the previous r46788 would:
CPUs hang at 100% after upload several files to its USB via samba.
After GUI installing this r46788 public release I uloaded a couple GBs and
she is all good showing CPUs going back to normal.
since I have previous r46788 listed as recommened on the EA8500 install webpage
I will change it to this public release
AND just so you know the r46788 public release has sha256sum =
2988bf90a9de8041d1c6bd2d8b26a7e0346f956a3ae572f20b6c157683b6f936
Last edited by mrjcd on Fri May 28, 2021 15:14; edited 1 time in total
Status: Working Fine running vanilla firmware type for 2.4ghz & 5ghz, uptime 15 Min, Samba Share still needs password even if set as public.
Switch Config tab working on R7800.
well shitdarn I thought we was all good but I reckon the silly ath10k:
firmware ver 10.4-ddwrt-9980-tW-13-6144M api 5 features mfp,peer-flow-ctrl,allows-mesh-bcast,peer-fixed-rate crc32 5506e25d
went to some far away place after 1 day little over 8hrs --- the 2.4 ... NO broadcast --NO nothing.
My 3 chromecast, couple desktops, & couple tablets all on 2.4 just went to shit, dead in the water.
The 5GHz was perfectly fine and doing what she is supposed to.
Anyways I switched both radios to the 'VANILLA' firmware and 2.4 came alive so we will see how she does after day or so.
bit of dmesg:
Code:
[ 34.575241] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: init_itable=0,nobarrier,nobh,barrier=0
[ 34.977861] Linux kernel CIFS/SMB SERVER 3.3.9 by Namjae Jeon <linkinjeon@kernel.org>
[ 35.345336] IMQ: use 2 as queue number
[ 35.352508] IMQ driver loaded successfully. (numdevs = 16, numqueues = 2, imq_dev_accurate_stats = 1)
[ 35.352535] Hooking IMQ after NAT on PREROUTING.
[ 35.360813] Hooking IMQ before NAT on POSTROUTING.
[ 38.301395] br1: port 1(wlan0.1) entered learning state
[ 52.301880] br1: port 2(vlan4) entered learning state
[ 53.301584] br1: port 1(wlan0.1) entered forwarding state
[ 67.301876] br1: port 2(vlan4) entered forwarding state
[116562.979985] device wlan0.1 left promiscuous mode
[116562.980133] br1: port 1(wlan0.1) entered disabled state
[116562.992798] device vlan4 left promiscuous mode
[116562.994627] br1: port 2(vlan4) entered disabled state
[116563.034230] br0: port 3(wlan1) entered disabled state
[116563.034400] br0: port 2(wlan0) entered disabled state
[116563.038429] br0: port 1(vlan1) entered disabled state
[116563.054878] device wlan1 left promiscuous mode
[116563.055021] br0: port 3(wlan1) entered disabled state
[116563.059226] device wlan0 left promiscuous mode
[116563.063517] br0: port 2(wlan0) entered disabled state
[116563.068505] device vlan1 left promiscuous mode
[116563.073057] device eth0 left promiscuous mode
[116563.077623] br0: port 1(vlan1) entered disabled state
[116563.525787] ath10k_pci 0000:01:00.0: No VIF found for vdev 1
[116563.525812] ath10k_pci 0000:01:00.0: no vif for vdev_id 1 found
[116563.559492] ath10k_pci 0000:01:00.0: peer-unmap-event: unknown peer id 1
[116563.559545] ath10k_pci 0000:01:00.0: peer-unmap-event: unknown peer id 1
[116563.565358] ath10k_pci 0000:01:00.0: peer-unmap-event: unknown peer id 1
[116563.678991] ath10k_pci 0001:01:00.0: peer-unmap-event: unknown peer id 0
[116563.679048] ath10k_pci 0001:01:00.0: peer-unmap-event: unknown peer id 0
[116563.684809] ath10k_pci 0001:01:00.0: peer-unmap-event: unknown peer id 0
[116563.828924] ath10k_pci 0000:01:00.0: peer-unmap-event: unknown peer id 0
[116563.828963] ath10k_pci 0000:01:00.0: peer-unmap-event: unknown peer id 0
[116564.396091] device br0 entered promiscuous mode
[116564.531095] br0: port 1(vlan1) entered blocking state
[116564.531125] br0: port 1(vlan1) entered disabled state
[116564.535501] device vlan1 entered promiscuous mode
[116564.540335] device eth0 entered promiscuous mode
[116564.545167] br0: port 1(vlan1) entered blocking state
[116564.549881] br0: port 1(vlan1) entered forwarding state
[116564.564428] device br0 left promiscuous mode
[116564.567052] device br0 entered promiscuous mode
[116564.630905] device br0 left promiscuous mode
[116564.694825] ath: EEPROM regdomain: 0x8348
[116564.694831] ath: EEPROM indicates we should expect a country code
[116564.694835] ath: doing EEPROM country->regdmn map search
[116564.694840] ath: country maps to regdmn code: 0x3a
[116564.694844] ath: Country alpha2 being used: US
[116564.694847] ath: Regpair used: 0x3a
[116564.694852] ath: regdomain 0x8348 dynamically updated by user
[116564.694867] ath: EEPROM regdomain: 0x8348
[116564.694870] ath: EEPROM indicates we should expect a country code
[116564.694873] ath: doing EEPROM country->regdmn map search
[116564.694877] ath: country maps to regdmn code: 0x3a
[116564.694880] ath: Country alpha2 being used: US
[116564.694882] ath: Regpair used: 0x3a
[116564.694886] ath: regdomain 0x8348 dynamically updated by user
[116564.704424] ath10k_pci 0000:01:00.0: user requested fw restart
[116564.794163] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0-vanilla/firmware-6.bin failed with error -2
[116565.032818] ath10k_pci 0000:01:00.0: found firmware features ie (4 B)
[116565.032852] ath10k_pci 0000:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003801ff sub 168c:0002
[116565.038316] ath10k_pci 0000:01:00.0: kconfig debug 1 debugfs 1 tracing 0 dfs 0 testmode 0
[116565.049741] ath10k_pci 0000:01:00.0: firmware ver 3.15-00018 api 5 features no-p2p,mfp,peer-flow-ctrl,allows-mesh-bcast,no-ps,peer-fixed-rate crc32 663fd9e8
[116565.113930] ath10k_pci 0000:01:00.0: boot get otp board id result 0x00008800 board_id 2 chip_id 1 ext_bid_support 0
[116565.113964] ath10k_pci 0000:01:00.0: boot using board name 'bus=pci,bmi-chip-id=1,bmi-board-id=2'
[116565.123587] ath10k_pci 0000:01:00.0: boot using board name 'bus=pci,bmi-chip-id=1,bmi-board-id=2'
[116565.132802] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 1:2 crc32 792a3d38
[116565.162400] ath10k_pci 0000:01:00.0: boot already acquired valid otp board id,skip download, board_id 2 chip_id 1
[116565.182953] ath10k_pci 0000:01:00.0: boot upload otp to 0x1234 len 11241
[116566.330446] ath10k_pci 0000:01:00.0: Init Max Stations to 512
[116566.404784] ath10k_pci 0000:01:00.0: wmi event ready sw_version 0x01000000 abi_version 3 mac_addr c0:56:27:06:39:fd status 0
[116566.435015] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 512 raw 0 hwcrypto 1
[116569.608061] ath10k_warn: 1 callbacks suppressed
[116569.608073] ath10k_pci 0000:01:00.0: wmi command 36872 timeout, restarting hardware
[116569.611778] ath10k_pci 0000:01:00.0: ani_enable failed from debugfs: -11
[116569.648450] ath10k_pci 0000:01:00.0: cannot restart a device that hasn't been started
[116569.895846] ath10k_pci 0000:01:00.0: boot get otp board id result 0x00008800 board_id 2 chip_id 1 ext_bid_support 0
[116569.916426] ath10k_pci 0000:01:00.0: boot upload otp to 0x1234 len 11241
[116571.066836] ath10k_pci 0000:01:00.0: Init Max Stations to 512
[116571.140372] ath10k_pci 0000:01:00.0: wmi event ready sw_version 0x01000000 abi_version 3 mac_addr c0:56:27:06:39:fd status 0
[116571.264672] ath10k_pci 0000:01:00.0: bdf failsafe status event received from fw: 0
[116571.272832] br0: port 2(wlan0) entered blocking state
[116571.272854] br0: port 2(wlan0) entered disabled state
[116571.277089] device wlan0 entered promiscuous mode
[116571.282129] br0: port 2(wlan0) entered blocking state
[116571.286750] br0: port 2(wlan0) entered forwarding state
[116571.292405] br0: port 2(wlan0) entered disabled state
[116573.395212] br0: port 2(wlan0) entered blocking state
[116573.395244] br0: port 2(wlan0) entered forwarding state
[116573.406763] br1: port 1(wlan0.1) entered blocking state
[116573.406794] br1: port 1(wlan0.1) entered disabled state
[116573.411588] device wlan0.1 entered promiscuous mode
[116573.423800] br1: port 1(wlan0.1) entered blocking state
[116573.576749] ath10k_pci 0001:01:00.0: user requested fw restart
[116573.669106] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0-vanilla/firmware-6.bin failed with error -2
[116573.669147] ath10k_pci 0001:01:00.0: found firmware features ie (4 B)
[116573.679470] ath10k_pci 0001:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003801ff sub 168c:0002
[116573.685981] ath10k_pci 0001:01:00.0: kconfig debug 1 debugfs 1 tracing 0 dfs 0 testmode 0
[116573.697440] ath10k_pci 0001:01:00.0: firmware ver 3.15-00018 api 5 features no-p2p,mfp,peer-flow-ctrl,allows-mesh-bcast,no-ps,peer-fixed-rate crc32 663fd9e8
[116573.761485] ath10k_pci 0001:01:00.0: boot get otp board id result 0x00008400 board_id 1 chip_id 1 ext_bid_support 0
[116573.761517] ath10k_pci 0001:01:00.0: boot using board name 'bus=pci,bmi-chip-id=1,bmi-board-id=1'
[116573.771154] ath10k_pci 0001:01:00.0: boot using board name 'bus=pci,bmi-chip-id=1,bmi-board-id=1'
[116573.780483] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id 1:1 crc32 792a3d38
[116573.809793] ath10k_pci 0001:01:00.0: boot already acquired valid otp board id,skip download, board_id 1 chip_id 1
[116573.830221] ath10k_pci 0001:01:00.0: boot upload otp to 0x1234 len 11241
[116574.976423] ath10k_pci 0001:01:00.0: Init Max Stations to 512
[116575.049194] ath10k_pci 0001:01:00.0: wmi event ready sw_version 0x01000000 abi_version 3 mac_addr c0:56:27:06:39:fd status 0
[116575.078780] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 512 raw 0 hwcrypto 1
[116578.257917] ath10k_pci 0001:01:00.0: wmi command 36872 timeout, restarting hardware
[116578.257971] ath10k_pci 0001:01:00.0: ani_enable failed from debugfs: -11
[116578.298156] ath10k_pci 0001:01:00.0: cannot restart a device that hasn't been started
[116578.485456] ath10k_pci 0001:01:00.0: boot get otp board id result 0x00008400 board_id 1 chip_id 1 ext_bid_support 0
[116578.505874] ath10k_pci 0001:01:00.0: boot upload otp to 0x1234 len 11241
[116579.649159] ath10k_pci 0001:01:00.0: Init Max Stations to 512
[116579.720154] ath10k_pci 0001:01:00.0: wmi event ready sw_version 0x01000000 abi_version 3 mac_addr c0:56:27:06:39:fd status 0
[116579.837300] ath10k_pci 0001:01:00.0: bdf failsafe status event received from fw: 0
[116579.844748] br0: port 3(wlan1) entered blocking state
[116579.844776] br0: port 3(wlan1) entered disabled state
[116579.849401] device wlan1 entered promiscuous mode
[116580.536925] br0: port 3(wlan1) entered blocking state
[116580.536956] br0: port 3(wlan1) entered forwarding state
[116580.801254] br1: port 2(vlan4) entered blocking state
[116580.803609] br1: port 2(vlan4) entered disabled state
[116580.808968] device vlan4 entered promiscuous mode
[116580.813812] br1: port 2(vlan4) entered blocking state
[116580.819194] br1: port 2(vlan4) entered blocking state
[116580.941213] ksmbd: kill command received
[116581.705317] Linux kernel CIFS/SMB SERVER 3.3.9 by Namjae Jeon <linkinjeon@kernel.org>
[116593.302100] br1: port 1(wlan0.1) entered learning state
[116600.301518] br1: port 2(vlan4) entered learning state
[116608.301416] br1: port 1(wlan0.1) entered forwarding state
[116615.301582] br1: port 2(vlan4) entered forwarding state
root@Citadel-Station-Homeworld:~# uptime
18:27:04 up 1 day, 8:29, load average: 0.03, 0.04, 0.00
root@Citadel-Station-Homeworld:~# date
Sat May 29 18:27:06 CDT 2021
root@Citadel-Station-Homeworld:~#
Connection to citadel-station-homeworld.mrjcd.com closed.
mrjcd@Fat-Deb:~$
Router/Version: Netgear R7800
File/Kernel: DD-WRT v3.0-r46788 std (05/28/21)
Previous/Reset: r46772/cli erase nvram
Mode/Status: Operational
Issues/Errors: Vanilla firmware for both radios
Uptime: about 30 hours
Had to switch to vanilla firmware to get my wireless-N clients to have reasonable download speeds. N on 2.4Ghz would yield less than 10Mbps down - N on 5Ghz wasn't much better. The AC clients seem happy with on 5Ghz radio with vanilla. _________________ Netgear R9000
Netgear R7800 (spare)
Linksys WRT1200ac v2 (spare)