New Build - 05/09/2021 - r46604

Post new topic   Reply to topic    DD-WRT Forum Index -> Broadcom SoC based Hardware
Goto page Previous  1, 2, 3, 4  Next
Author Message
amadeus
DD-WRT Novice


Joined: 06 Nov 2019
Posts: 38

PostPosted: Mon May 10, 2021 19:15    Post subject: Reply with quote
Router/Version: Netgear r6700v3
Firmware: DD-WRT v3.0-r46604 std (05/09/21)
Kernel: Linux 4.4.268 #2925 SMP Sun May 9 06:37:15 +07 2021 armv7l
Mode: Wireless AP.
Reset: Nope.
Previous: 03/12/2021 - r45993
Status: Working fine so far. CTF can be chosen as shortcut forwarding engine but flow acceleration is not being applied. Goes back to disabled after router reboot.
Temperatures: CPU 73.6 °C / WL0 47.2 °C / WL1 56.4 °C



log.txt
 Description:
boot log

Download
 Filename:  log.txt
 Filesize:  30.78 KB
 Downloaded:  105 Time(s)

Sponsor
lpy
DD-WRT Novice


Joined: 17 Oct 2017
Posts: 38

PostPosted: Mon May 10, 2021 20:45    Post subject: Reply with quote
amadeus wrote:
Working fine so far. CTF can be chosen as shortcut forwarding engine but flow acceleration is not being applied. Goes back to disabled after router reboot.

I'm sure someone will correct if I'm wrong but I remember reading something a long time ago that it can't be used with QoS. So you'll have to pick one or the other.
amadeus
DD-WRT Novice


Joined: 06 Nov 2019
Posts: 38

PostPosted: Mon May 10, 2021 21:22    Post subject: Reply with quote
lpy wrote:
amadeus wrote:
Working fine so far. CTF can be chosen as shortcut forwarding engine but flow acceleration is not being applied. Goes back to disabled after router reboot.

I'm sure someone will correct if I'm wrong but I remember reading something a long time ago that it can't be used with QoS. So you'll have to pick one or the other.

I've also heard about that, but I have QoS disabled. So there has to be another reason.
kernel-panic69
DD-WRT Guru


Joined: 08 May 2018
Posts: 14125
Location: Texas, USA

PostPosted: Mon May 10, 2021 21:26    Post subject: Re: Q Reply with quote
kooper2013 wrote:
kernel-panic69 wrote:
@kooper2013:

The Asus RT-AC87U 5GHz doesn't work in DD-WRT due to them being Quantenna hardware and no drivers that will work with current kernel, etc. This is a known issue that will never be fixed.


I know the Quantenna was and is problematic, but 5GHz was working in previous builds of March and April. I'm following the SVN quite a bit and didn't notice any related changes there.
So take it as a hint to others, nothing more and nothing less.


AFAIK, there is *NO* Quantenna drivers in DD-WRT, so I don't know *how* the 5GHz was ever working. And a lot of times, you will *NOT* see certain things in public SVN (driver_repository_changelogs).

_________________
"Life is but a fleeting moment, a vapor that vanishes quickly; All is vanity"
Contribute To DD-WRT
Pogo - A minimal level of ability is expected and needed...
DD-WRT Releases 2023 (PolitePol)
DD-WRT Releases 2023 (RSS Everything)

----------------------
Linux User #377467 counter.li.org / linuxcounter.net
itwontbewe
DD-WRT User


Joined: 29 Sep 2020
Posts: 260
Location: United States

PostPosted: Tue May 11, 2021 1:12    Post subject: Reply with quote
Router: Netgear R7000P
Kernel: Linux 4.4.268 #2931 SMP Sun May 9 07:02:31 +07 2021 armv7l
Reset: no
Mode/Status: Gateway AP 2.4GHz 5Ghz IPv6 Unbound custom conf JFFS2 SFE:Disable static leases / working
Issues: running well thanks BrainSlayer and dd-wrt community


Last edited by itwontbewe on Sat May 22, 2021 14:10; edited 2 times in total
lpy
DD-WRT Novice


Joined: 17 Oct 2017
Posts: 38

PostPosted: Tue May 11, 2021 2:05    Post subject: Reply with quote
amadeus wrote:
lpy wrote:
amadeus wrote:
Working fine so far. CTF can be chosen as shortcut forwarding engine but flow acceleration is not being applied. Goes back to disabled after router reboot.

I'm sure someone will correct if I'm wrong but I remember reading something a long time ago that it can't be used with QoS. So you'll have to pick one or the other.

I've also heard about that, but I have QoS disabled. So there has to be another reason.

Yeah must be something else. If I disable QoS, FA remains enabled. According to the internets it's not compatible with "Port Forwarding, QoS, IP Traffic Monitor, and Parental Control."
kooper2013
DD-WRT User


Joined: 10 Jan 2013
Posts: 109
Location: DE

PostPosted: Tue May 11, 2021 21:10    Post subject: Re: Q Reply with quote
kernel-panic69 wrote:

AFAIK, there is *NO* Quantenna drivers in DD-WRT, so I don't know *how* the 5GHz was ever working. And a lot of times, you will *NOT* see certain things in public SVN (driver_repository_changelogs).


https://svn.dd-wrt.com/search?q=quantenna
and
https://svn.dd-wrt.com/search?q=qtn

The useless auto commit changelogs for the 'blob' should not be related to qtn.

-eod-

_________________
3xBuffalo WLI-H4-D1300
1xBuffalo WZR-D1800H
1xBuffalo WHR-HP-G300N
1xBuffalo WHR-1166D (stock f/w)
1xAsus RT-AC87U
1xAsus RT-AC88U
1xTP710
kernel-panic69
DD-WRT Guru


Joined: 08 May 2018
Posts: 14125
Location: Texas, USA

PostPosted: Tue May 11, 2021 21:50    Post subject: Re: Q Reply with quote
kooper2013 wrote:
kernel-panic69 wrote:

AFAIK, there is *NO* Quantenna drivers in DD-WRT, so I don't know *how* the 5GHz was ever working. And a lot of times, you will *NOT* see certain things in public SVN (driver_repository_changelogs).

https://svn.dd-wrt.com/search?q=quantenna
and
https://svn.dd-wrt.com/search?q=qtn

The useless auto commit changelogs for the 'blob' should not be related to qtn.

-eod-

I could've been mistaken with another firmware project here; if it's not working, re-open the ticket with syslogs or provide applicable information here. Just saying it doesn't work means zero.

https://svn.dd-wrt.com/ticket/7051

I just added a link to the current GPL tarball to this ticket:

https://svn.dd-wrt.com/ticket/5351

Keep in mind, the RT-AC87U 5GHz webUI functionality doesn't work as most people would expect, and BrainSlayer in not so many words told me it won't be fixed.

_________________
"Life is but a fleeting moment, a vapor that vanishes quickly; All is vanity"
Contribute To DD-WRT
Pogo - A minimal level of ability is expected and needed...
DD-WRT Releases 2023 (PolitePol)
DD-WRT Releases 2023 (RSS Everything)

----------------------
Linux User #377467 counter.li.org / linuxcounter.net
jrscs
DD-WRT User


Joined: 09 Aug 2010
Posts: 413

PostPosted: Wed May 12, 2021 16:54    Post subject: RT-AC87u A1 Reply with quote
Starting with r46604 the 5 GHz radio (wl1) has not worked on RT-AC87u A1. There is no visible SSID being broadcast and no connections from devices that worked on prior r46446. Even when the router has been reset to factory defaults there is no radio present (SSID broadcast).

Enclosed are log files which might point to the issue.



dmesg.txt
 Description:
dmesg.txt

Download
 Filename:  dmesg.txt
 Filesize:  9.74 KB
 Downloaded:  101 Time(s)


catmessages.txt
 Description:
catmessages.txt

Download
 Filename:  catmessages.txt
 Filesize:  4.3 KB
 Downloaded:  102 Time(s)


syslog.txt
 Description:
syslog

Download
 Filename:  syslog.txt
 Filesize:  3.89 KB
 Downloaded:  87 Time(s)


_________________
Netgear XR500, R7800
Asus AC87Ua1
Repeater Bridge
Netgear R6400v2otp
kernel-panic69
DD-WRT Guru


Joined: 08 May 2018
Posts: 14125
Location: Texas, USA

PostPosted: Wed May 12, 2021 17:07    Post subject: RE: RT-AC87U Reply with quote
I have emailed BrainSlayer about this issue, I have not received a response yet. He will either reply to my email or respond in this thread, I do not know which.
_________________
"Life is but a fleeting moment, a vapor that vanishes quickly; All is vanity"
Contribute To DD-WRT
Pogo - A minimal level of ability is expected and needed...
DD-WRT Releases 2023 (PolitePol)
DD-WRT Releases 2023 (RSS Everything)

----------------------
Linux User #377467 counter.li.org / linuxcounter.net
thommy181
DD-WRT User


Joined: 16 Mar 2019
Posts: 353
Location: Szczecin, Poland EU

PostPosted: Wed May 12, 2021 17:38    Post subject: New Build - 05/09/2021 - r46604 Reply with quote
Router/Version: Netgear WNR3500L v2
Kernel: Linux 4.4.268 #8666 Sun May 9 11:38:16 +07 2021 mips
Reset: No
Mode: Internet gateway, WIFI AP, dnsmasq server
Status: Working
Uptime: ~ 54h
Errors: Router working rather good. I have many errors and warnings in log. (ex. Login data are good, but I have information about incorrect password / login...)

Quote:
Jan 1 01:00:14 Myrouter kern.warn kernel: Found a AMD NAND flash with 2048B pages or 128KB blocks; total size 128MB
Jan 1 01:00:14 kern.warn kernel: Primary instruction cache 32kB, 4-way, VIPT, I-cache aliases, linesize 32 bytes.
Jan 1 01:00:14 kern.warn kernel: Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Jan 1 01:00:14 kern.warn kernel: PCI: no core
Jan 1 01:00:14 kern.warn kernel: PCI: no core
Jan 1 01:00:14 kern.warn kernel: PCI: Fixing up bridge
Jan 1 01:00:14 kern.warn kernel: PCI: Fixing up bus 0
Jan 1 01:00:14 kern.err kernel: pflash: found no supported devices
Jan 1 01:00:14 kern.warn kernel: ERROR: Unknown flash, device_id:0x00
Jan 1 01:00:14 kern.err kernel: bcmsflash: found no supported devices
Jan 1 01:00:14 kern.warn kernel: Boot partition size = 524288(0x80000)
Jan 1 01:00:14 kern.warn kernel: lookup_nflash_rootfs_offset: offset = 0x500000
Jan 1 01:00:14 kern.warn kernel: nf_conntrack_rtsp v0.7 loading
Jan 1 01:00:14 kern.warn kernel: et_module_init: passivemode set to 0x0
Jan 1 01:00:14 kern.warn kernel: et_module_init: txworkq set to 0x0
Jan 1 01:00:14 kern.warn kernel: et_module_init: et_txq_thresh set to 0xce4
Jan 1 01:00:14 kern.warn kernel: et_module_init: et_rxlazy_timeout set to 0x3e8
Jan 1 01:00:14 kern.warn kernel: et_module_init: et_rxlazy_framecnt set to 0x20
Jan 1 01:00:14 kern.warn kernel: et_module_init: et_rxlazy_dyn_thresh set to 0
Jan 1 01:00:14 kern.warn kernel: et_module_init: et_ctf_disable set to 1
Jan 1 01:00:14 kern.warn kernel: eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 7.14.164.18 (r692288)
Jan 1 01:00:14 kern.err kernel: roboswitch: error (-14) while accessing MII phy registers with ioctls
Jan 1 01:00:14 kern.err kernel: roboswitch: No such device
Jan 1 01:00:14 kern.err kernel: roboswitch: No such device
Jan 1 01:00:14 kern.err kernel: roboswitch: No such device
Jan 1 01:00:14 kern.warn kernel: wl: module license 'Proprietary' taints kernel.
Jan 1 01:00:14 kern.warn kernel: Disabling lock debugging due to kernel taint
Jan 1 01:00:14 kern.warn kernel: bcm_robo_config_vlan_fun vid=1, vlan->members=0x11e, vlan->untag=0x1e
Jan 1 01:00:14 kern.warn kernel: bcm_robo_config_vlan_fun ports=1 2 3 4 8t
Jan 1 01:00:14 kern.warn kernel: bcm_robo_config_vlan_fun vid=2, vlan->members=0x101, vlan->untag=0x101
Jan 1 01:00:14 kern.warn kernel: bcm_robo_config_vlan_fun ports=0 8
Jan 1 01:00:15 kern.warn kernel: bcm_robo_config_vlan_fun vid=1, vlan->members=0x118, vlan->untag=0x18
Jan 1 01:00:15 kern.warn kernel: bcm_robo_config_vlan_fun ports=3 4 8t
Jan 1 01:00:15 kern.warn kernel: bcm_robo_config_vlan_fun vid=2, vlan->members=0x101, vlan->untag=0x1
Jan 1 01:00:15 kern.warn kernel: bcm_robo_config_vlan_fun ports=0 81t
May 10 16:24:16 kern.warn kernel: br0: received packet on eth1 with own address as source address
May 10 16:27:19 kern.warn kernel: br0: received packet on eth1 with own address as source address
May 10 18:00:42 daemon.err httpd[1619]: httpd : Request Error Code 401: Authorization required. Wrong username and/or password!
May 11 07:56:11 daemon.err httpd[1619]: httpd : Request Error Code 401: Authorization required. Wrong username and/or password!
May 11 16:17:43 kern.warn kernel: br0: received packet on eth1 with own address as source address
May 11 16:27:40 kern.warn kernel: br0: received packet on eth1 with own address as source address
May 11 18:11:55 daemon.err httpd[11264]: httpd : Request Error Code 401: Authorization required. Wrong username and/or password!
May 11 18:15:56 kern.warn kernel: br0: received packet on eth1 with own address as source address
May 11 18:15:58 kern.warn kernel: br0: received packet on eth1 with own address as source address
May 11 18:17:55 kern.warn kernel: br0: received packet on eth1 with own address as source address
May 11 18:18:20 kern.warn kernel: br0: received packet on eth1 with own address as source address
May 11 18:18:22 kern.warn kernel: br0: received packet on eth1 with own address as source address
May 11 18:37:20 daemon.err httpd[16008]: httpd : Request Error Code 401: Authorization required. Wrong username and/or password!
May 11 18:45:19 kern.warn kernel: br0: received packet on eth1 with own address as source address
May 11 18:47:31 kern.warn kernel: br0: received packet on eth1 with own address as source address
May 11 18:48:12 kern.warn kernel: br0: received packet on eth1 with own address as source address
May 11 18:51:15 kern.warn kernel: br0: received packet on eth1 with own address as source address
May 11 18:54:18 kern.warn kernel: br0: received packet on eth1 with own address as source address
May 11 18:55:43 kern.warn kernel: br0: received packet on eth1 with own address as source address
May 11 18:55:51 kern.warn kernel: br0: received packet on eth1 with own address as source address
May 11 18:56:31 kern.warn kernel: br0: received packet on eth1 with own address as source address
May 11 18:56:51 kern.warn kernel: br0: received packet on eth1 with own address as source address
May 11 18:57:06 kern.warn kernel: br0: received packet on eth1 with own address as source address
May 11 18:57:14 kern.warn kernel: br0: received packet on eth1 with own address as source address
May 11 18:57:32 kern.warn kernel: br0: received packet on eth1 with own address as source address
May 11 18:57:50 kern.warn kernel: br0: received packet on eth1 with own address as source address
May 11 18:58:33 kern.warn kernel: br0: received packet on eth1 with own address as source address
May 11 19:01:35 kern.warn kernel: br0: received packet on eth1 with own address as source address
May 12 08:03:15 kern.warn kernel: br0: received packet on eth1 with own address as source address
May 12 08:06:17 kern.warn kernel: br0: received packet on eth1 with own address as source address
May 12 08:59:24 daemon.err httpd[16008]: httpd : Request Error Code 401: Authorization required. Wrong username and/or password!
May 12 12:18:14 kern.warn kernel: br0: received packet on eth1 with own address as source address
May 12 12:18:28 kern.warn kernel: br0: received packet on eth1 with own address as source address
May 12 12:21:44 kern.warn kernel: br0: received packet on eth1 with own address as source address
May 12 12:24:46 kern.warn kernel: br0: received packet on eth1 with own address as source address
May 12 13:38:09 kern.warn kernel: br0: received packet on eth1 with own address as source address
May 12 13:38:23 kern.warn kernel: br0: received packet on eth1 with own address as source address
May 12 13:38:37 kern.warn kernel: br0: received packet on eth1 with own address as source address
May 12 13:38:48 kern.warn kernel: br0: received packet on eth1 with own address as source address
May 12 19:03:06 daemon.err httpd[16008]: httpd : Request Error Code 401: Authorization required. Wrong username and/or password!
kooper2013
DD-WRT User


Joined: 10 Jan 2013
Posts: 109
Location: DE

PostPosted: Wed May 12, 2021 20:08    Post subject: Re: Q Reply with quote
kernel-panic69 wrote:

I could've been mistaken with another firmware project here; if it's not working, re-open the ticket with syslogs or provide applicable information here. Just saying it doesn't work means zero.

https://svn.dd-wrt.com/ticket/7051

I just added a link to the current GPL tarball to this ticket:

https://svn.dd-wrt.com/ticket/5351

Keep in mind, the RT-AC87U 5GHz webUI functionality doesn't work as most people would expect, and BrainSlayer in not so many words told me it won't be fixed.


I know that BS was p*ssed about the qtn-driver and several things can't be set nor read. Thanks for the link on svn. I don't think BS will do anything.

Nothing in the syslog related to qtn/quantenna. Attached.



ac87-syslog-r46604.zip
 Description:

Download
 Filename:  ac87-syslog-r46604.zip
 Filesize:  7.45 KB
 Downloaded:  116 Time(s)


_________________
3xBuffalo WLI-H4-D1300
1xBuffalo WZR-D1800H
1xBuffalo WHR-HP-G300N
1xBuffalo WHR-1166D (stock f/w)
1xAsus RT-AC87U
1xAsus RT-AC88U
1xTP710
BrainSlayer
Site Admin


Joined: 06 Jun 2006
Posts: 7463
Location: Dresden, Germany

PostPosted: Thu May 13, 2021 5:51    Post subject: Re: 5GHZ not working Reply with quote
kooper2013 wrote:
Router/Version: Asus RT-AC87U
File/Kernel: asus_rt-ac87u-firmware.trx, Linux 4.4.268 #2933 SMP Sun May 9 07:09:58 +07 2021 armv7l
Previous/Reset: r46294, no
Mode/Status: Router, WAP, WG-client
Issues/Errors: 5GHz not working

5GHz is not working. Parameters are WPA2 only, AC/N mixed, VHT80, upper/upper.
SSID is not seen by iPhone nor AVM 3000 (a repeater).

Also wireguard stopped working after ~20 minutes.

Flashed twice, also TRX-files verified (to exclude a bad flash).
Going back, can't use this build.


i'm sure wireguard is totally unrelated here. there is nothing i have changed on wireguard over a long time. i suspect that your peer has a problem

beside this. post logs next time (syslog, whatever). its hard to work with spare informations

update:
5 ghz wifi problem will be fixed with next build. discovered and fixed the problem already

_________________
"So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
kooper2013
DD-WRT User


Joined: 10 Jan 2013
Posts: 109
Location: DE

PostPosted: Thu May 13, 2021 9:04    Post subject: Re: 5GHZ not working Reply with quote
BrainSlayer wrote:


i'm sure wireguard is totally unrelated here. there is nothing i have changed on wireguard over a long time. i suspect that your peer has a problem

beside this. post logs next time (syslog, whatever). its hard to work with spare informations

update:
5 ghz wifi problem will be fixed with next build. discovered and fixed the problem already


Great & thanks, BS (+KP)! I was reluctant to post LOGs due to low userbase and qtn radio used on very few devices (Netgear R7500, Linksys E8350, E8400, this AC87, some siblings and more rare devices). Also jrscs just confirmed.

wg was probably unrelated to the new build, but was working on previous build 5 minutes before. Will look at the LOGs next time. Promised.

https://svn.dd-wrt.com/changeset/46643
Perhaps I can also get my AC88 back from retirement.

_________________
3xBuffalo WLI-H4-D1300
1xBuffalo WZR-D1800H
1xBuffalo WHR-HP-G300N
1xBuffalo WHR-1166D (stock f/w)
1xAsus RT-AC87U
1xAsus RT-AC88U
1xTP710
BrainSlayer
Site Admin


Joined: 06 Jun 2006
Posts: 7463
Location: Dresden, Germany

PostPosted: Thu May 13, 2021 15:12    Post subject: Reply with quote
the new build is already out. i tested it specific on a ac87
_________________
"So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
Goto page Previous  1, 2, 3, 4  Next Display posts from previous:    Page 2 of 4
Post new topic   Reply to topic    DD-WRT Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum