New Build - 04/24/2021 - r46446

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Atheros WiSOC based Hardware
Goto page Previous  1, 2
Author Message
xl600
DD-WRT Novice


Joined: 04 Dec 2019
Posts: 24

PostPosted: Mon Apr 26, 2021 18:59    Post subject: Reply with quote
ayandon wrote:
xl600 wrote:
The first is that ntpclient refuses to operate. I’ve tried leaving the server field blank, tried us.pool.ntp.org, tried an internal ntp server (which I use for everything inside my lan), and even a cron job. None work. I can log in via ssh and issue “ntpclient us.pool.ntp.org” and get a timesync, but it never works automatically. Granted, I’ve only had this router for a week but this has never been an issue with any other router I’ve used with ddwrt (wrt3200acm among others).


Use this IP as NTP server and check - 129.6.15.28


I had read various posts about using ip addresses directly, but that didn’t work either. I tried 129.6.15.28 and the ip of my internal server.

Sigh....
Sponsor
surfkiller20
DD-WRT Novice


Joined: 23 Feb 2012
Posts: 3

PostPosted: Mon Apr 26, 2021 19:08    Post subject: Reply with quote
tatsuya46 wrote:


and vanilla radio firmware is tried?


Vanilla causes random Connection loss on wlan1. Bridge becomes unusable for a Couple of minutes, Sometimes 5Ghz Radio Stopps working. Only with a reboot 5 GHz is usable again.
At the Moment, 5 GHz With dd-wrt Firmware is Most stable.

I also try different Old Builds Form 2019 and 2020. Same behaviour.
When i build the Bridge on 2,4GHz i don't have this Trouble but Performance on 5 GHz is much better
madmark
DD-WRT Novice


Joined: 29 Jul 2019
Posts: 27

PostPosted: Mon Apr 26, 2021 22:45    Post subject: Reply with quote
Router Model: TP-Link ARCHER-C5 v1
Kernel Version: Linux 3.18.140-d5
Previous/Reset: 04/23/2021 - r46442 / No
Mode/Status: Gateway /2.4 GHz,5.0 GHz, IPv4, Port Forwarding, NTP TimeSync, Samba, VPN
Issues/Errors: router is resetting itself every 30 seconds , When is connected usb drive 128 GB router restarts. When is unplugged usb drive router works.

Jan 1 01:00:13 DD-WRT syslog.info syslogd started: BusyBox v1.33.0
Jan 1 01:00:13 DD-WRT user.info : klogd : daemon successfully started
Jan 1 01:00:13 DD-WRT kern.notice kernel: klogd started: BusyBox v1.33.0 (2021-04-24 08:35:47 +07)
Jan 1 01:00:13 DD-WRT kern.notice kernel: [ 0.000000] Linux version 3.18.140-d6 (root@linux) (gcc version 9.2.0 (OpenWrt GCC 9.2.0 r10890-7d542dc804) ) #113933 Sat Apr 24 08:35:30 +07 2021
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 0.000000] bootconsole [early0] enabled
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
Jan 1 01:00:13 DD-WRT kern.warn kernel: [ 0.000000] cpu apb ddr apb cpu 720 ddr 600 ahb 200
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 0.000000] sys id = 1130 Qualcomm Atheros QCA9558 ver 1 rev 1.0 (0x1130)
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 0.000000] Determined physical RAM map:
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 0.000000] memory: 08000000 @ 00000000 (usable)
Jan 1 01:00:13 DD-WRT kern.warn kernel: [ 0.000000] Zone ranges:
Jan 1 01:00:13 DD-WRT kern.warn kernel: [ 0.000000] Normal [mem 0x00000000-0x07ffffff]
Jan 1 01:00:13 DD-WRT kern.warn kernel: [ 0.000000] Movable zone start for each node
Jan 1 01:00:13 DD-WRT kern.warn kernel: [ 0.000000] Early memory node ranges
Jan 1 01:00:13 DD-WRT kern.warn kernel: [ 0.000000] node 0: [mem 0x00000000-0x07ffffff]
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x07ffffff]
Jan 1 01:00:13 DD-WRT kern.debug kernel: [ 0.000000] On node 0 totalpages: 32768
Jan 1 01:00:13 DD-WRT kern.debug kernel: [ 0.000000] free_area_init_node: node 0, pgdat 802e37a0, node_mem_map 81000000
Jan 1 01:00:13 DD-WRT kern.debug kernel: [ 0.000000] Normal zone: 256 pages used for memmap
Jan 1 01:00:13 DD-WRT kern.debug kernel: [ 0.000000] Normal zone: 0 pages reserved
Jan 1 01:00:13 DD-WRT kern.debug kernel: [ 0.000000] Normal zone: 32768 pages, LIFO batch:7
Jan 1 01:00:13 DD-WRT kern.warn kernel: [ 0.000000] Primary instruction cache 64kB, 4-way, VIPT, linesize 32 bytes.
Jan 1 01:00:13 DD-WRT kern.warn kernel: [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Jan 1 01:00:13 DD-WRT kern.debug kernel: [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
Jan 1 01:00:13 DD-WRT kern.debug kernel: [ 0.000000] pcpu-alloc: [0] 0
Jan 1 01:00:13 DD-WRT kern.warn kernel: [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
Jan 1 01:00:13 DD-WRT kern.notice kernel: [ 0.000000] Kernel command line: console=ttyS0,115200 root=1f02 rootfstype=squashfs noinitrd init=/sbin/init
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 0.000000] Writing ErrCtl register=00000000
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 0.000000] Readback ErrCtl register=00000000
Jan 1 01:00:13 DD-WRT kern.warn kernel: [ 0.000000] Memory: 126560K/131072K available (2263K kernel code, 154K rwdata, 244K rodata, 144K init, 144K bss, 4512K reserved, 0K cma-reserved)
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 0.000000] NR_IRQS:83
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 0.060000] Calibrating delay loop... 358.80 BogoMIPS (lpj=1794048)
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 0.060000] pid_max: default: 32768 minimum: 301
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 0.060000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 0.070000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 0.070000] NET: Registered protocol family 16
Jan 1 01:00:13 DD-WRT kern.debug kernel: [ 0.080000] ar71xx: using random MAC address for eth0
Jan 1 01:00:13 DD-WRT kern.debug kernel: [ 0.280000] ar71xx: using random MAC address for eth1
Jan 1 01:00:13 DD-WRT kern.warn kernel: [ 0.480000] ar724x-pci ar724x-pci.0: PCIe link is down
Jan 1 01:00:13 DD-WRT kern.warn kernel: [ 0.490000] registering PCI controller with io_map_base unset
Jan 1 01:00:13 DD-WRT kern.warn kernel: [ 0.490000] registering PCI controller with io_map_base unset
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 0.510000] PCI host bridge to bus 0000:00
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 0.510000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff]
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 0.520000] pci_bus 0000:00: root bus resource [io 0x0000]
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 0.520000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
Jan 1 01:00:13 DD-WRT kern.debug kernel: [ 0.530000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
Jan 1 01:00:13 DD-WRT kern.notice kernel: [ 0.800000] 0x000000ff0000-0x000001000000 : "board_config"
Jan 1 01:00:13 DD-WRT kern.notice kernel: [ 0.800000] 0x000000000000-0x000001000000 : "fullflash"
Jan 1 01:00:13 DD-WRT kern.notice kernel: [ 0.810000] 0x000000000000-0x000000020000 : "fullboot"
Jan 1 01:00:13 DD-WRT kern.notice kernel: [ 0.810000] 0x000000010000-0x000000020000 : "uboot-env"
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 0.820000] libphy: Fixed MDIO Bus: probed
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 0.830000] u32 classifier
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 0.830000] Performance counters on
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 0.840000] input device check on
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 0.840000] Actions configured
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 0.840000] Netfilter messages via NETLINK v0.30.
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 0.850000] nf_conntrack version 0.5.0 (1977 buckets, 7908 max)
Jan 1 01:00:13 DD-WRT kern.warn kernel: [ 0.850000] nf_conntrack_rtsp v0.7 loading
Jan 1 01:00:13 DD-WRT kern.warn kernel: [ 0.860000] nf_nat_rtsp v0.7 loading
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 0.860000] ip_tables: (C) 2000-2006 Netfilter Core Team
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 10.600000] ath10k_pci 0000:01:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
Jan 1 01:00:13 DD-WRT kern.warn kernel: [ 10.800000] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:01:00.0.bin failed with error -2
Jan 1 01:00:13 DD-WRT kern.warn kernel: [ 10.810000] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/cal-pci-0000:01:00.0.bin failed with error -2
Jan 1 01:00:13 DD-WRT kern.warn kernel: [ 10.820000] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-6.bin failed with error -2
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 11.070000] ath10k_pci 0000:01:00.0: found firmware features ie (4 B)
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 11.080000] ath10k_pci 0000:01:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 11.090000] ath10k_pci 0000:01:00.0: kconfig debug 1 debugfs 1 tracing 0 dfs 0 testmode 0
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 11.100000] ath10k_pci 0000:01:00.0: firmware ver 10.2.4-97.2-ddwrt-6155M api 5 features wmi-10.x,no-p2p,wmi-10.2,raw-mode,mfp,allows-mesh-bcast,peer-fixed-rate crc32 f20d852a
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 11.140000] ath10k_pci 0000:01:00.0: boot get otp board id result 0x00000001 board_id 0 chip_id 0 ext_bid_support 0
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 11.150000] ath10k_pci 0000:01:00.0: board id does not exist in otp, ignore it (0)
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 11.150000] ath10k_pci 0000:01:00.0: boot using board name 'bus=pci,vendor=168c,device=003c,subsystem-vendor=0000,subsystem-device=0000'
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 11.170000] ath10k_pci 0000:01:00.0: boot using board name 'bus=pci,vendor=168c,device=003c,subsystem-vendor=0000,subsystem-device=0000'
Jan 1 01:00:13 DD-WRT kern.warn kernel: [ 11.180000] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 11.190000] ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A crc32 9e0a5c0f
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 11.200000] ath10k_pci 0000:01:00.0: boot upload otp to 0x1234 len 6211
Jan 1 01:00:13 DD-WRT kern.warn kernel: [ 11.230000] ath10k_pci 0000:01:00.0: otp stream is empty, using board.bin contents
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 11.880000] nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead.
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 12.130000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 1 is up
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 12.130000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 2 is up
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 12.140000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 3 is up
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 12.150000] ath10k_pci 0000:01:00.0: Init Max Stations to 128
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 12.170000] ath10k_pci 0000:01:00.0: P 135 V 16 T 433
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 12.180000] ath10k_pci 0000:01:00.0: alloc rem: 8440 iram: 30420
Jan 1 01:00:13 DD-WRT kern.info kernel: [ 12.190000] ath10k_pci 0000:01:00.0: wmi event ready sw_version 0x41000061 abi_version 1 mac_addr 14:cc:20:67:bf:35 status 0
Jan 1 01:00:28 DD-WRT kern.info kernel: [ 28.370000] ath10k_pci 0000:01:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
Jan 1 01:00:28 DD-WRT kern.info kernel: [ 28.380000] ath10k_pci 0000:01:00.0: kconfig debug 1 debugfs 1 tracing 0 dfs 0 testmode 0
Jan 1 01:00:28 DD-WRT kern.info kernel: [ 28.390000] ath10k_pci 0000:01:00.0: firmware ver 10.2.4-1.0-00047 api 5 features wmi-10.x,no-p2p,wmi-10.2,raw-mode,mfp,allows-mesh-bcast,peer-fixed-rate crc32 35bd9258
Jan 1 01:00:28 DD-WRT kern.info kernel: [ 28.450000] ath10k_pci 0000:01:00.0: boot get otp board id result 0x00000001 board_id 0 chip_id 0 ext_bid_support 0
Jan 1 01:00:28 DD-WRT kern.info kernel: [ 28.460000] ath10k_pci 0000:01:00.0: board id does not exist in otp, ignore it (-2144456208)
Jan 1 01:00:28 DD-WRT kern.info kernel: [ 28.470000] ath10k_pci 0000:01:00.0: boot using board name 'bus=pci,vendor=168c,device=003c,subsystem-vendor=0000,subsystem-device=0000'
Jan 1 01:00:28 DD-WRT kern.info kernel: [ 28.480000] ath10k_pci 0000:01:00.0: boot using board name 'bus=pci,vendor=168c,device=003c,subsystem-vendor=0000,subsystem-device=0000'
Jan 1 01:00:28 DD-WRT kern.warn kernel: [ 28.490000] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
Jan 1 01:00:28 DD-WRT kern.warn kernel: [ 28.500000] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board_2.bin failed with error -2
Jan 1 01:00:28 DD-WRT kern.info kernel: [ 28.520000] ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A crc32 9e0a5c0f
Jan 1 01:00:28 DD-WRT kern.info kernel: [ 28.530000] ath10k_pci 0000:01:00.0: boot upload otp to 0x1234 len 7221
Jan 1 01:00:28 DD-WRT kern.warn kernel: [ 28.680000] ath10k_pci 0000:01:00.0: otp stream is empty, using board.bin contents
Jan 1 01:00:29 DD-WRT kern.info kernel: [ 29.360000] br0: port 1(eth1) entered forwarding state
Jan 1 01:00:29 DD-WRT kern.info kernel: [ 29.890000] ath10k_pci 0000:01:00.0: Init Max Stations to 118
Jan 1 01:00:29 DD-WRT kern.info kernel: [ 29.900000] ath10k_pci 0000:01:00.0: P 135 V 16 T 433
Jan 1 01:00:29 DD-WRT kern.info kernel: [ 29.910000] ath10k_pci 0000:01:00.0: wmi event ready sw_version 0x4100002f abi_version 1 mac_addr 14:cc:20:67:bf:35 status 0
Jan 1 01:00:29 DD-WRT kern.info kernel: [ 29.920000] ath10k_pci 0000:01:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta 118 raw 0 hwcrypto 1
Jan 1 01:00:30 DD-WRT kern.info kernel: [ 30.240000] ath10k_pci 0000:01:00.0: boot upload otp to 0x1234 len 7221
Jan 1 01:00:30 DD-WRT kern.warn kernel: [ 30.390000] ath10k_pci 0000:01:00.0: otp stream is empty, using board.bin contents
Jan 1 01:00:31 DD-WRT kern.info kernel: [ 31.440000] ath10k_pci 0000:01:00.0: Init Max Stations to 118
Jan 1 01:00:31 DD-WRT kern.info kernel: [ 31.450000] ath10k_pci 0000:01:00.0: P 135 V 16 T 433
Jan 1 01:00:31 DD-WRT kern.info kernel: [ 31.460000] ath10k_pci 0000:01:00.0: wmi event ready sw_version 0x4100002f abi_version 1 mac_addr 14:cc:20:67:bf:35 status 0
Jan 1 01:00:31 DD-WRT kern.warn kernel: [ 31.470000] ath10k_pci 0000:01:00.0: pdev param 0 not supported by firmware
Jan 1 01:00:31 DD-WRT kern.warn kernel: [ 31.500000] ath10k_pci 0000:01:00.0: failed to set vdev 0 tx encap mode: -122
Jan 1 01:00:31 DD-WRT kern.info kernel: [ 31.500000] ath10k_pci 0000:01:00.0: Mac CLK 88
Jan 1 01:00:37 DD-WRT kern.notice kernel: [ 37.180000] random: nonblocking pool is initialized
Jan 1 01:00:38 DD-WRT kern.info kernel: [ 38.000000] ath10k_pci 0000:01:00.0: boot upload otp to 0x1234 len 7221
Jan 1 01:00:38 DD-WRT kern.warn kernel: [ 38.150000] ath10k_pci 0000:01:00.0: otp stream is empty, using board.bin contents
Jan 1 01:00:39 DD-WRT kern.info kernel: [ 39.200000] ath10k_pci 0000:01:00.0: Init Max Stations to 118
Jan 1 01:00:39 DD-WRT kern.info kernel: [ 39.210000] ath10k_pci 0000:01:00.0: P 135 V 16 T 433
Jan 1 01:00:39 DD-WRT kern.info kernel: [ 39.220000] ath10k_pci 0000:01:00.0: wmi event ready sw_version 0x4100002f abi_version 1 mac_addr 14:cc:20:67:bf:35 status 0
Jan 1 01:00:39 DD-WRT kern.warn kernel: [ 39.240000] ath10k_pci 0000:01:00.0: pdev param 0 not supported by firmware
Jan 1 01:00:39 DD-WRT kern.warn kernel: [ 39.260000] ath10k_pci 0000:01:00.0: failed to set vdev 0 tx encap mode: -122
Jan 1 01:00:39 DD-WRT kern.info kernel: [ 39.270000] device wlan1 entered promiscuous mode
Jan 1 01:00:39 DD-WRT kern.info kernel: [ 39.400000] br0: port 3(wlan1) entered forwarding state
Jan 1 01:00:39 DD-WRT kern.info kernel: [ 39.400000] br0: port 3(wlan1) entered forwarding state
Jan 1 01:00:39 DD-WRT user.info : bridge : interface wlan1 successfully added to bridge br0
Jan 1 01:00:40 DD-WRT user.info : hwmon : successfully started
Jan 1 01:00:40 DD-WRT user.info : klogd : kernel log daemon successfully stopped
Jan 1 01:00:40 DD-WRT kern.info kernel: [ 40.160000] device eth0 entered promiscuous mode
Jan 1 01:00:40 DD-WRT user.info : telnetd : daemon successfully started
Jan 1 01:00:40 DD-WRT kern.notice kernel: klogd: exiting
Jan 1 01:00:40 DD-WRT user.info : sfe : shortcut forwarding engine successfully stopped
Jan 1 01:00:41 DD-WRT kern.info kernel: [ 41.730000] gre: GRE over IPv4 demultiplexor driver
Jan 1 01:00:41 DD-WRT user.info : proftpd : server successfully started
Jan 1 01:00:42 DD-WRT kern.warn kernel: [ 42.250000] pptp: Unknown symbol pppox_ioctl (err 0)
Jan 1 01:00:42 DD-WRT kern.warn kernel: [ 42.250000] pptp: Unknown symbol ppp_register_channel (err 0)
Jan 1 01:00:42 DD-WRT kern.warn kernel: [ 42.260000] pptp: Unknown symbol ppp_input (err 0)
Jan 1 01:00:42 DD-WRT kern.warn kernel: [ 42.270000] pptp: Unknown symbol unregister_pppox_proto (err 0)
Jan 1 01:00:42 DD-WRT kern.warn kernel: [ 42.270000] pptp: Unknown symbol register_pppox_proto (err 0)
Jan 1 01:00:42 DD-WRT kern.warn kernel: [ 42.280000] pptp: Unknown symbol pppox_unbind_sock (err 0)
Jan 1 01:00:43 DD-WRT kern.info kernel: [ 43.040000] br0: port 2(wlan0) entered forwarding state
Jan 1 01:00:43 DD-WRT kern.info kernel: [ 43.680000] PPP generic driver version 2.4.2
Jan 1 01:00:44 DD-WRT kern.info kernel: [ 44.320000] PPP BSD Compression module registered
Jan 1 01:00:44 DD-WRT daemon.info httpd[975]: httpd : httpd server started at port 80
Jan 1 01:00:44 DD-WRT kern.info kernel: [ 44.780000] PPP Deflate Compression module registered
Jan 1 01:00:44 DD-WRT user.info : httpd : http daemon successfully started
Jan 1 01:00:45 DD-WRT kern.info kernel: [ 45.310000] PPP MPPE Compression module registered
Jan 1 01:00:45 DD-WRT user.info : minidlna : DLNA Media Server successfully started
Jan 1 01:00:45 DD-WRT kern.info kernel: [ 45.910000] NET: Registered protocol family 24
Jan 1 01:00:46 DD-WRT daemon.info pptpd[1051]: MGR: Maximum of 64 connections reduced to 5, not enough IP addresses given
Jan 1 01:00:46 DD-WRT user.info : pptpd : daemon successfully started
Jan 1 01:00:46 DD-WRT daemon.debug pptpd[1061]: CTRL: BCrelay incoming interface is br0
Jan 1 01:00:46 DD-WRT daemon.info pptpd[1061]: MGR: Manager process started
Jan 1 01:00:46 DD-WRT daemon.info pptpd[1061]: MGR: Maximum of 5 connections available
Jan 1 01:00:46 DD-WRT daemon.debug pptpd[1062]: CTRL (BCrelay Launcher): Launching BCrelay with pid 0
Jan 1 01:00:46 DD-WRT daemon.debug pptpd[1062]: MGR: BCrelay incoming interface is br0
Jan 1 01:00:46 DD-WRT daemon.debug pptpd[1062]: MGR: BCrelay outgoing interface is regexp ppp[0-9].*
Jan 1 01:00:47 DD-WRT daemon.info bcrelay[1062]: Running as child
Jan 1 01:00:47 DD-WRT kern.warn kernel: [ 47.840000] ipt_TRIGGER: module license 'unspecified' taints kernel.
Jan 1 01:00:47 DD-WRT kern.warn kernel: [ 47.850000] Disabling lock debugging due to kernel taint
Jan 1 01:00:48 DD-WRT kern.info kernel: [ 48.370000] Linux kernel CIFS/SMB SERVER 3.3.9 by Namjae Jeon
Jan 1 01:00:48 DD-WRT user.info wsdd2[1103]: starting.
Jan 1 01:00:48 DD-WRT user.err wsdd2[1103]: error: wsdd-mcast-v4: wsd_send_soap_msg: send: Network unreachable
Jan 1 01:00:48 DD-WRT user.info : smbd : samba started
Jan 1 01:00:48 DD-WRT local5.err ksmbd: [ksmbd-manager/1106]: ERROR: Can't open `/tmp/ksmbd.subauth': No such file or directory
Jan 1 01:00:48 DD-WRT local5.info ksmbd: [ksmbd-worker/1107]: INFO: User already exists nobody
Jan 1 01:00:48 DD-WRT kern.alert kernel: [ 48.850000] fast-classifier (PBR safe v2.1.6b): starting up
Jan 1 01:00:48 DD-WRT kern.alert kernel: [ 48.850000] fast-classifier: registered
Jan 1 01:00:48 DD-WRT user.info : sfe : shortcut forwarding engine successfully started
Jan 1 01:00:49 DD-WRT kern.info kernel: [ 49.090000] ip6_tables: (C) 2000-2006 Netfilter Core Team
Jan 1 01:00:49 DD-WRT user.info : sfe : shortcut forwarding engine successfully started
Jan 1 01:00:49 DD-WRT kern.info kernel: [ 49.770000] eth0: link down
Jan 1 01:00:49 DD-WRT kern.info kernel: [ 49.780000] device eth0 left promiscuous mode
Jan 1 01:00:49 DD-WRT user.info : ttraff : traffic counter daemon successfully started
Apr 27 00:36:47 DD-WRT kern.debug kernel: [ 277.340000] sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
Apr 27 00:36:47 DD-WRT kern.err kernel: [ 277.340000] sd 0:0:0:0: [sda] No Caching mode page found
Apr 27 00:36:47 DD-WRT kern.err kernel: [ 277.350000] sd 0:0:0:0: [sda] Assuming drive cache: write through
Apr 27 00:36:47 DD-WRT kern.info kernel: [ 277.360000] sda: sda1
Apr 27 00:36:47 DD-WRT kern.notice kernel: [ 277.370000] sd 0:0:0:0: [sda] Attached SCSI removable disk
Apr 27 00:36:47 DD-WRT user.info : cron : daemon successfully stopped
Apr 27 00:36:47 DD-WRT user.info : wsdd2 : windows service discovery daemon successfully stopped
Apr 27 00:36:47 DD-WRT user.err wsdd2[1103]: Terminated received.
Apr 27 00:36:47 DD-WRT user.info wsdd2[1103]: terminating.
Apr 27 00:36:47 DD-WRT user.info : ksmbd.mountd : samba daemon successfully stopped
Apr 27 00:36:47 DD-WRT local5.info ksmbd: [ksmbd-worker/1107]: INFO: Child received signal: 15 (Terminated)
Apr 27 00:36:47 DD-WRT local5.err ksmbd: [ksmbd-manager/1106]: ERROR: WARNING: child process exited abnormally: 1107
Apr 27 00:36:47 DD-WRT local5.err ksmbd: [ksmbd-manager/1106]: ERROR: can't execute kill 1107: No such process
Apr 27 00:36:47 DD-WRT local5.info ksmbd: [ksmbd-manager/1106]: INFO: Exiting. Bye!
Apr 27 00:36:47 DD-WRT user.info : minidlna : DLNA Media Server successfully stopped
Apr 27 00:36:47 DD-WRT kern.info kernel: [ 277.800000] ksmbd: kill command received
Apr 27 00:36:51 DD-WRT kern.info kernel: [ 281.290000] ANTFS Module: Version 1.0
Apr 27 00:36:51 DD-WRT user.info : cron : daemon successfully started
Apr 27 00:36:51 DD-WRT cron.info cron[2431]: (CRON) STARTUP (fork ok)
Apr 27 00:36:52 DD-WRT kern.info kernel: [ 282.430000] Linux kernel CIFS/SMB SERVER 3.3.9 by Namjae Jeon
Apr 27 00:36:52 DD-WRT user.info wsdd2[2492]: starting.
Apr 27 00:36:52 DD-WRT user.info : smbd : samba started
Apr 27 00:36:52 DD-WRT local5.info ksmbd: [ksmbd-worker/2497]: INFO: User already exists nobody
Apr 27 00:36:52 DD-WRT user.info : minidlna : DLNA Media Server successfully started
Apr 27 00:36:53 DD-WRT user.info : proftpd : server successfully started
Apr 27 00:36:54 DD-WRT user.info : cron : daemon successfully stopped
Apr 27 00:36:54 DD-WRT user.info : cron : daemon successfully started
Apr 27 00:36:54 DD-WRT cron.info cron[2544]: (CRON) STARTUP (fork ok)
Apr 27 00:36:55 DD-WRT user.info wsdd2[2605]: starting.
Apr 27 00:36:55 DD-WRT user.info : smbd : samba started
Apr 27 00:36:55 DD-WRT local5.info ksmbd: [ksmbd-manager/2610]: INFO: File '/tmp/ksmbd.lock' belongs to pid 2496
Apr 27 00:36:55 DD-WRT local5.err ksmbd: [ksmbd-manager/2610]: ERROR: Failed to create lock file: File exists
Apr 27 00:36:55 DD-WRT local5.info ksmbd: [ksmbd-manager/2610]: INFO: Exiting. Bye!
Apr 27 00:36:55 DD-WRT user.info : minidlna : DLNA Media Server successfully stopped
Apr 27 00:36:55 DD-WRT user.info : minidlna : DLNA Media Server successfully started
Apr 27 00:36:55 DD-WRT user.info : proftpd : server successfully started
Apr 27 00:37:06 DD-WRT kern.alert kernel: [ 295.780000] CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == 00000000, ra == 800e6e90
Apr 27 00:37:06 DD-WRT kern.warn kernel: [ 295.790000] Oops[#1]:
Apr 27 00:37:06 DD-WRT kern.warn kernel: [ 295.790000] CPU: 0 PID: 2626 Comm: minidlna Tainted: P 3.18.140-d6 #113933
Apr 27 00:37:06 DD-WRT kern.warn kernel: [ 295.790000] task: 87f9da48 ti: 850ce000 task.ti: 850ce000
Apr 27 00:37:06 DD-WRT kern.warn kernel: [ 295.790000] $ 0 : 00000000 80320000 00000000 000007ff
Apr 27 00:37:06 DD-WRT kern.warn kernel: [ 295.790000] $ 4 : 850cfe80 850cfeb8 00000001 850cff10
Apr 27 00:37:06 DD-WRT kern.warn kernel: [ 295.790000] $ 8 : 00000038 80068b98 800e7ffc 000000c6
Apr 27 00:37:06 DD-WRT kern.warn kernel: [ 295.790000] $12 : 7fd971e0 77bb51d0 77bae4f0 7fd9765f
Apr 27 00:37:06 DD-WRT kern.warn kernel: [ 295.790000] $16 : 850cff10 87ec4f20 00000400 850cff10
Apr 27 00:37:06 DD-WRT kern.warn kernel: [ 295.790000] $20 : 00000400 00000001 00000400 77b6ce50
Apr 27 00:37:06 DD-WRT kern.warn kernel: [ 295.790000] $24 : 00000000 77b6c9f8
Apr 27 00:37:06 DD-WRT kern.warn kernel: [ 295.790000] $28 : 850ce000 850cfe68 00000000 800e6e90
Apr 27 00:37:06 DD-WRT kern.warn kernel: [ 295.790000] Hi : 00000000
Apr 27 00:37:06 DD-WRT kern.warn kernel: [ 295.790000] Lo : 00000e28
Apr 27 00:37:06 DD-WRT kern.warn kernel: [ 295.790000] epc : 00000000 (null)
Apr 27 00:37:06 DD-WRT kern.warn kernel: [ 295.790000] Tainted: P
Apr 27 00:37:06 DD-WRT kern.warn kernel: [ 295.790000] ra : 800e6e90 0x800e6e90
Apr 27 00:37:06 DD-WRT kern.warn kernel: [ 295.790000] Status: 1000fc03 KERNEL EXL IE
Apr 27 00:37:06 DD-WRT kern.warn kernel: [ 295.790000] Cause : 00800008
Apr 27 00:37:06 DD-WRT kern.warn kernel: [ 295.790000] BadVA : 00000000
Apr 27 00:37:06 DD-WRT kern.warn kernel: [ 295.790000] PrId : 00019750 (MIPS 74Kc)
Apr 27 00:37:06 DD-WRT kern.warn kernel: [ 295.790000] Modules linked in: ksmbd antfs fast_classifier nf_nat_pptp nf_conntrack_pptp nf_nat_proto_gre nf_conntrack_proto_gre xt_pkttype usblp usb_storage sr_mod cdrom sd_mod scsi_mod ehci_platform ehci_hcd usbcore usb_com
Apr 27 00:37:06 DD-WRT kern.warn kernel: [ 295.790000] Process minidlna (pid: 2626, threadinfo=850ce000, task=87f9da48, tls=77bb6de4)
Apr 27 00:37:06 DD-WRT kern.warn kernel: [ 295.790000] Stack : 007b21d8 00000400 850cff28 77b6f000 00000000 000007ff 87ec4f20 00000000
Apr 27 00:37:06 DD-WRT kern.warn kernel: [ 295.790000] 00000000 00000000 87f9da48 00000000 00000000 00000000 00000000 000007ff
Apr 27 00:37:06 DD-WRT kern.warn kernel: [ 295.790000] 00000400 00000000 00000000 00000000 007b21d8 00000400 00000400 87ec4f20
Apr 27 00:37:06 DD-WRT kern.warn kernel: [ 295.790000] 007b21d8 800e7bb0 00000000 800e8634 850cff08 800e71f4 00000000 87ec4f20
Apr 27 00:37:06 DD-WRT kern.warn kernel: [ 295.790000] 007b21d8 00000400 77b29080 800e8064 87ec4f20 00000000 00000001 005e94d0
Apr 27 00:37:06 DD-WRT kern.warn kernel: [ 295.790000] ...
Apr 27 00:37:06 DD-WRT kern.warn kernel: [ 295.790000] Call Trace:[<800e7bb0>] 0x800e7bb0
Apr 27 00:37:06 DD-WRT kern.warn kernel: [ 295.790000] [<800e8634>] 0x800e8634
Apr 27 00:37:06 DD-WRT kern.warn kernel: [ 295.790000] [<800e71f4>] 0x800e71f4
Apr 27 00:37:06 DD-WRT kern.warn kernel: [ 295.790000] [<800e8064>] 0x800e8064
Apr 27 00:37:06 DD-WRT kern.warn kernel: [ 295.790000] [<8006679c>] 0x8006679c
Apr 27 00:37:06 DD-WRT kern.warn kernel: [ 295.790000]
Apr 27 00:37:06 DD-WRT kern.warn kernel: [ 295.790000]
Apr 27 00:37:06 DD-WRT kern.warn kernel: [ 295.790000] Code: (Bad address in epc)
Apr 27 00:37:06 DD-WRT kern.warn kernel: [ 295.790000]
Apr 27 00:37:06 DD-WRT kern.warn kernel: [ 296.030000] ---[ end trace e23533376f9fab63 ]---
hsar
DD-WRT Novice


Joined: 30 Apr 2021
Posts: 1

PostPosted: Fri Apr 30, 2021 8:55    Post subject: Reply with quote
If your USB drive is NTFS formatted, then that's probably the cause.
Rebooting occurs -at least accourding to my experience with 4 different router models- when you are actually trying to access a file on an NTFS drive. Please note subsequent reboots might be caused by the device that initially tried to access the file retries to do so after the router's reboot.

What seems to work:
- Fat32 formatted drive
- SMB version 2.10 (or lower). With v3 or above, there seem to be issues when actually attempting to read files.
ayandon
DD-WRT Novice


Joined: 20 Nov 2019
Posts: 10

PostPosted: Fri Apr 30, 2021 12:39    Post subject: Reply with quote
hsar wrote:
If your USB drive is NTFS formatted, then that's probably the cause.
Rebooting occurs -at least accourding to my experience with 4 different router models- when you are actually trying to access a file on an NTFS drive. Please note subsequent reboots might be caused by the device that initially tried to access the file retries to do so after the router's reboot.

What seems to work:
- Fat32 formatted drive
- SMB version 2.10 (or lower). With v3 or above, there seem to be issues when actually attempting to read files.



Pls read the issue.

It was and is working on older version v3.0-r45735 but NOT in the latest version.
Zyxx
DD-WRT User


Joined: 28 Dec 2018
Posts: 397

PostPosted: Fri Apr 30, 2021 15:34    Post subject: Reply with quote
Router/Version: Netgear R7800
File: factory-to-ddwrt.img
Firmware: DD-WRT v3.0-r46446 std (04/24/21) (prev. stock)
Kernel: Linux 4.9.267 #150 SMP Sat Apr 24 05:46:20 +07 2021 armv7l
Mode: Gateway, 2.4G and 5G wifi, Wireguard for external access, WAN to 4G, Keep Alive reboot 6:02 in the morning
Reset: No
Status: Ok, 2h up.
SuninderSingh
DD-WRT Novice


Joined: 05 Sep 2017
Posts: 28
Location: IN

PostPosted: Wed May 05, 2021 19:43    Post subject: Reply with quote
Router/Version: TP-Link TL-WR841ND v9
Firmware: DD-WRT v3.0-r46446 std (04/24/21)
Kernel: Linux 3.18.140-d6 #113913 Sat Apr 24 08:14:47 +07 2021 mips
Reset: Yes
Status: Ok, GUI very fast from previous!! Just click and page load Very Happy

_________________
>>TP-Link TL-WR841ND v9
>>DD-WRT v3.0-r43397 std (06/13/20)
>>TP-Link TL-WR841ND v9
>>DD-WRT v3.0-r45735 std (02/11/21)
madmark
DD-WRT Novice


Joined: 29 Jul 2019
Posts: 27

PostPosted: Sat May 08, 2021 5:41    Post subject: Reply with quote
hsar wrote:
If your USB drive is NTFS formatted, then that's probably the cause.
Rebooting occurs -at least accourding to my experience with 4 different router models- when you are actually trying to access a file on an NTFS drive. Please note subsequent reboots might be caused by the device that initially tried to access the file retries to do so after the router's reboot.

What seems to work:
- Fat32 formatted drive
- SMB version 2.10 (or lower). With v3 or above, there seem to be issues when actually attempting to read files.


I have usb drive formatted in NTSF. I Changed the SMB version on 2.10 and the problem is the same. Router restarts when the drive is plugged in usb in router.
egc
DD-WRT Guru


Joined: 18 Mar 2014
Posts: 7693
Location: Netherlands

PostPosted: Sat May 08, 2021 10:25    Post subject: Reply with quote
Router Model: Netgear R7800

Firmware Version: DD-WRT v3.0-r46446 std (04/24/21)
Kernel Version: Linux 4.9.267 #150 SMP Sat Apr 24 05:46:20 +07 2021 armv7l

Upgraded from: DD-WRT v3.0-r46329 std (04/13/21)

Reset: No, not this time

Status: Up and running for 7 days , basic setup as Gateway, static leases, 2,4GHz, 5Ghz (Vanilla Firmware), OpenVPN Server with site-to-site setup and local DNS working.
WireGuard client to Keepsolid working, WireGuard server working.

Errors: Nothing encountered yet (but not tested USB/NAS)

Thanks BS!

_________________
Routers:Netgear R7800, R6400v1, R6400v2, Linksys EA8500, EA6900 (XvortexCFE), E2000 (converted WRT320N), WRT54GS v1.
WireGuard Documents & Guides:https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=327397
OpenVPN Documents & Guides: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=327398
IPSET: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=327261
Install guide R6400v2:http://forum.dd-wrt.com/phpBB2/viewtopic.php?t=316399
Install guide R7800: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=320614
Forum Guide Lines (important read):https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=324087
Alozaros
DD-WRT Guru


Joined: 16 Nov 2015
Posts: 4378
Location: UK, London, just across the river..

PostPosted: Sat May 08, 2021 14:40    Post subject: Reply with quote
Router Model Netgear R7800
Firmware Version DD-WRT v3.0-r46446 std (04/24/21)
Kernel Version Linux 4.9.267 #150 SMP Sat Apr 24 05:46:20 +07 2021 armv7l

update: cli
reset: yes
status: buggy/operational
errors: On my R7800 I just moved from DDWRT to Vanilla, still the same WiFi drops on various devices, very randomly, mainly on Windows 10 20H2 and on iPhones, but very random...
Wi-Fi on 1043v2 behaves rock solid...so, it must be a function that is present on R7800, but not on 1043v2 i need to investigate...both running almost similar WiFi config... will do R7800 reset to see if this helps...

P.S. After reset recompile R7800 2,4Ghz WiFi problem still exist...there are random drops, mainly Qualcomm/Intel/Broadcom coexistence impossible, but very random...in log it says connected/disconnected almost immediately on connection try..and device connects as it should on 3-4 attempt, sometimes it never connects...router restarts solves the issue for a while and comes back...tried various options.....

Been using the same setting for ages...NGmixed tried Mixed as well..Channel 11 + lower, Short GI, Short Preamble...not RTS/CTS protection, also tried hostapd

basic_rates=60 120 240
supported_rates=60 90 120 180 240 360 480 540

no avail at all

on 1043v2 it happens in a different way devices connects, but no traffic and it needs another few try's...until...

i've no idea if problem occurs just because updated Win 10 to 20H2 or iPhones to last 14.5.1....

_________________
Atheros
TP-Link WR740Nv1 -----DD-WRT 46446 BS AP,NAT
TP-Link WR740Nv4 -----DD-WRT 44251 BS WAP/Switch
TP-Link WR1043NDv2 ---DD-WRT 46885 BS AP,NAT,AP Isolation,Ad-Block,Firewall,Local DNS,Forced DNS,DoT,VPN,VLAN
TP-Link WR1043NDv2 ---DD-WRT 46885 BS AP,NAT,AD/Block,Firewall,Local DNS,Forced DNS,DoT,VPN,VLAN
TP-Link WR1043NDv2 ---Gargoyle OS 1.12.0 AP,NAT,QoS,Quotas
Qualcomm/IPQ8065
Netgear R7800 -----DD-WRT 46885 BS AP,NAT,AD-Block,AP&Net Isolation,VLAN's,Firewall,Local DNS,DoT
Broadcom
Netgear R7000 -----DD-WRT 46885 BS AP,Wi-Fi OFF,NAT,AD-Block,Firewall,Local DNS,Forced DNS,VLAN's,DoT,VPN
-----------------------------------------------------------------------------------------------
Stubby for DNS over TLS I DNSCrypt v2 by mac913
zloy_elektrik
DD-WRT Novice


Joined: 15 Jan 2012
Posts: 11
Location: Kiev, Ukraine

PostPosted: Sat May 08, 2021 19:21    Post subject: Reply with quote
Router/Version: tp-link 1043 v1 w/ ram mod
File/Kernel: Firmware: DD-WRT v3.0-r46446 std (04/24/21)
Previous/Reset: r46220, no reset
Mode/Status: gateway+AP, gigabit wan, uptime 2 days since last reboot
WAN-LAN throughput good, around 600+ mbps
I was using my 1043 v1 unit for a long time with r36104 build (as any newer build was leading to bootlop). I don't remember any WIFI problems with r36104. (but on r36104 there are was no encryption on wifi, just open AP)
On r46220 wifi hangs for sereral times a day.
On r46446 seems to be pretty stable. I did iperf for 2 hours each direction, PC-gigabit lan-1043v1-wifi-old laptop. Around 30mbps pc>laptop and around 50mbps laptop>pc.
Wifi settings are: AP, NG-mixed, WideHT40, Channel 6 + lower. I think i changed nothing in advanced settings. I've got 2 error messedge (telnet>dmesg), but wifi still works, no need to power cycle the unit.
Code:
<3>[65143.450000] ath: phy0: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42100020 DMADBG_7=0x000286c0
<3>[68041.980000] ath: phy0: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42100020 DMADBG_7=0x000084c0

I'll test wifi again later, it was hanging mostly when macbook pro (late 2013 model) was online. Maybe macbook was the case, i think i shoud test it with macbook doing some wifi traffic.
kqboat
DD-WRT Novice


Joined: 02 Dec 2014
Posts: 2

PostPosted: Sat May 08, 2021 20:24    Post subject: TP-Link A7 AC1750 V5 Reply with quote
Router/Version: tp-link A7 AC1750 V5
Firmware: DD-WRT v3.0-r46446 std (04/24/21)

Not sure if this is the correct place to share this, but there were questions on what speeds you could get for A7 AC1750.

I just installed the latest firmware yesterday 5/7/21. I have 1G internet up/down and I confirm that I am able to get upwards to 900M+ up/down, although more consistently between 600M - 800M. Port forwarding working fine, DDNS to freedns.afraid.org working as well.

It's only been working 2 days, but hoping for stability in the long run. the original stock firmware (sorry, forgot the version number) was fine for a few weeks, then no internet until I rebooted. I believe this is a common TP-Link stock firmware issue. Hence, the move to DD-WRT.
tedm
DD-WRT User


Joined: 13 Mar 2009
Posts: 428

PostPosted: Sat May 08, 2021 22:26    Post subject: Reply with quote
Router/Version: Buffalo WHR-G300N V2
File/Kernel: Linux 3.10.108-d11 #79324 Sat Apr 24 06:56:14 +07 2021 mips
Previous/Reset: Yes
Mode/Status: OK
Issues/Errors: None

This device was updated from Buffalo's WHR-G300N Ver.1.80 (R2.01/B1.00) firmware using the "trailed" (encrypted) build. Router was factory reset from the Buffalo firmware, then the trailed build installed. On reboot the router was inaccessible until pressing the reset button on the bottom for around 5 seconds. That reset it and I was then able to login. Contains a 400Mhz Atheros CPU but is 2.6Ghz only.
Rocketboy235
DD-WRT User


Joined: 14 Oct 2016
Posts: 102
Location: United States

PostPosted: Sun May 09, 2021 3:44    Post subject: Reply with quote
Rocketboy235 wrote:
Update method: SSH / CLI
Router/Version: Linksys EA8500
File/Kernel: DD-WRT v3.0-r46446 std (04/24/21)
Previous/Reset: DD-WRT v3.0-44719 std (11/03/20) / No
Mode/Status: Gateway / Working Normally
Issues/Errors: None

Been running for half an hour so far and no issues as of yet...

Going to try out the Vanilla firmware type in the WiFi settings and hope that my previous issues mentioned here:
https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=325230
are no longer happening.


So far, speeds look decent. I still need to test for any possible performance degradation after a few days running without restarting it.

One issue I noticed after upgrading to this new firmware is that some of my devices could not connect to the 2.4 GHz network. All the mobile devices (iPhone and Android) and laptops could but my desktops could not. Not sure if it had to do with the kind of wireless chip in the clients. I also ended up doing a hard reset on the router.

I found out after I disabled "TurboQAM (QAM256) support" for the 2.4 GHz network, the issue went away.

I'm not sure why this is causing an issue now since I think I remember seeing this option enabled in my previous DD-WRT firmware builds and never had an issue with this enabled.

One thing that is different is I also temporarily turned this router into a wireless access point (ethernet backhaul) and connecting it to one of my other recently updated DD-WRT routers but not sure if that could play a role.

_________________
DD-WRT Router Arsenal:

Linksys EA8500 - BS 46446 (previously r44719)
TP Link TL-WR1043ND v1.8 - BS 42819 (previously r45955)
Motorola WR850G v3 - BS 21286
Rocketboy235
DD-WRT User


Joined: 14 Oct 2016
Posts: 102
Location: United States

PostPosted: Thu May 20, 2021 0:25    Post subject: Reply with quote
Posting an update regarding my previous posts. Looks like my issues have for the most part cleared up that I have experienced in here: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=325230

What I did was I used the DD-WRT for the firmware type instead of Vanilla and it seems to be a lot more consistent in speed for both 2.4 GHz and 5 GHz. Still need to wait a few weeks (without the router resetting) to make sure it stays consistent but been a week so far and things are looking good.

_________________
DD-WRT Router Arsenal:

Linksys EA8500 - BS 46446 (previously r44719)
TP Link TL-WR1043ND v1.8 - BS 42819 (previously r45955)
Motorola WR850G v3 - BS 21286
Goto page Previous  1, 2 Display posts from previous:    Page 2 of 2
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Atheros WiSOC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum