Posted: Fri Apr 23, 2021 12:44 Post subject: New Build - 04/23/2021 - r46442
[WARNING]: This thread is only for feedback on this beta release for developers and the community's benefit.
DO NOT flash this beta release unless you understand the risks involved and device specificrecovery methods.
Avoid discussions! Create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
• Show us your findings with steps to reproduce, configuration, output, logs and important information below!
• For issues provide applicable info: 'dmesg', 'cat /tmp/var/log/messages', syslog, klog, serial, strace, tcpdump, wireshark etc.
• Any firewall NAT or WAN issues, show output: 'iptables -vnL', 'iptables -t nat -vnL', 'iptables -t mangle -vnL' and /tmp/.ipt file.
• Search SVN tickets & discuss in forum before opening. Before reporting: reset & manually set up, not restore from a backup.
• Please include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) & relevant configuration information.
Router Model: TP-Link ARCHER-C5 v1
Kernel Version: Linux 3.18.140-d5
Previous/Reset: 04/13/2021 - r46329 / No
Mode/Status: Gateway /2.4 GHz,5.0 GHz, IPv4, Port Forwarding, NTP TimeSync, Samba, VPN
Issues/Errors: router is resetting itself every 30 seconds , When is connected usb drive 128 GB router restarts. When is unplugged usb drive router works. Not working wireless 5g light/diode.
Router Model / Version: Linksys EA8500
Previous Firmware:DD-WRT v3.0-r46395 std (04/19/21)
Current Firmware: DD-WRT v3.0-r46442 std (04/23/21)
Kernel: Linux 4.9.267 #146 SMP Wed Apr 21 06:00:03 +07 2021 armv7l
Mode: Wireless - Client, Operating - Gateway
Setup: SFE, NTP, DDNS (inadyn-Entware), DNSMasq (GUI+ additional options on USB, Syslog, SSH,FreeRadius, Telnet, USB, ProFTPD (with users), Samba (with users), CoovaChilli (with local users & radius), WiFiDog, Remote Access (HTTPS & SSH), Startup Script (For DNSMasq & inadyn)
Uptime: up 10:32, load average: 0.00, 0.00, 0.00
Temperature: CPU 55.755 °C / wlan0 45 °C / wlan1 47 °C
Issues: The issues with the WifiDog client noted in the previous builds (r46380) has been resolved. As long as the "AuthServer SSL Available" option is disabled, WiFiDog will work, providing users already setup an Auth Server.
If the "AuthServer SSL Available" parameter is enabled in the GUI users might face an issue. By default the "SSLPeerVerification" paramenter is enabled in the config. However it's only active once the "AuthServer SSL Available" parameter is enabled. To ensure everything works you must have the following already setup.
A jffs partition
Auth Server Cert located in the /jffs/etc/ssl/certs/
Auth Server cert must be named by it's hash value
In my case it works since I already have it all setup.
Suggestion: Can we add the "SSLPeerVerification" parameter to the GUI and at the same time add the "SSLCertPath" parameter as well in case users use a different directory to store their certs. If that's not possible then a way to notify users that this needs to be setup in order for WifiDog to work with SSL support.
Question: Was the default config file location changed? I saw this "#define DEFAULT_CONFIGFILE "/jffs/etc/wifidog.conf"" in Changeset 46425 but it doesn't seem to work. WifiDog is still referencing the old directory. Currently WifiDog use the config file "tmp/wifidog/wifidog.conf" when it's enabled in the GUI.
[Sat Apr 24 19:08:52 2021](../../src/conf.c:651) Reading configuration file '/usr/etc/wifidog.conf'
[Sat Apr 24 19:08:52 2021](../../src/conf.c:654) Could not open configuration file '/usr/etc/wifidog.conf', exiting...