Posted: Tue Feb 23, 2021 14:19 Post subject: New Build - 02/23/2021 - r45820
[WARNING]: This thread is only for feedback on this beta release for developers and the community's benefit.
DO NOT flash this beta release unless you understand the risks involved and device specificrecovery methods.
Avoid discussions! Create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues:
• Show us your findings with steps to reproduce, configuration, output, logs and important information below!
Important:
• For issues provide applicable info: 'dmesg', 'cat /tmp/var/log/messages', syslog, klog, serial, strace, tcpdump, wireshark etc.
• Any firewall NAT or WAN issues, show output: 'iptables -vnL', 'iptables -t nat -vnL', 'iptables -t mangle -vnL' and /tmp/.ipt file.
• Search SVN tickets & discuss in forum before opening. Before reporting: reset & manually set up, not restore from a backup.
• Please include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) & relevant configuration information.
Router/Version: R7800
Firmware: DD-WRT v3.0-r45820 std (02/23/21)
Kernel: Linux 4.9.257 #1157 SMP Tue Feb 23 02:37:39 +07 2021 armv7l
Previous: DD-WRT v3.0-r45767 std (02/17/21)
Mode/Status: Gateway/AP/Ok
Reset: No
Setup Using: 2.4 GHz, 2.4 GHz guest (VAP), 5.0 GHz, IPv4, DNSMasq, Port Forwarding, USB, NAS, Samba NTFS, NTP TimeSync, VNC Repeater, and Wake-on-WAN (internet)
Issues/Errors: Yes, Samba NTFS came up dirty [not available!] after upgrade. Required to remove USB from router, connect to Windows 10, repair drive, and attach back to router USB port.
Update: After 12 hours devices were loosing internet access on 2.4 GHz so rolled back to r45767 _________________ Netgear XR500, R7800
Asus AC87Ua1
Repeater Bridge
Netgear R6400v2otp
Last edited by jrscs on Wed Feb 24, 2021 10:22; edited 1 time in total
Joined: 16 Nov 2015 Posts: 6440 Location: UK, London, just across the river..
Posted: Tue Feb 23, 2021 18:28 Post subject:
Router Model TP-Link WR1043ND V2
Firmware Version DD-WRT v3.0-r45820 std (02/23/21)
Kernel Version Linux 3.18.140-d5 #107713 Tue Feb 23 05:55:45 +06 2021 mips
update: CLI
reset: NO
status: Operational 6h+
errors: Nothing new...so far so good ...will report later... _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55630 WAP
TP-Link WR1043NDv2 -DD-WRT 55723 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55779 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55819 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55779 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
Router Model: Netgear R7800
Firmware: DD-WRT v3.0-r45820 std (02/23/21)
Kernel: Linux 4.9.257 #1157 SMP Tue Feb 23 02:37:39 +07 2021 armv7l
Previous: DD-WRT v3.0-r45735
Mode/Status: Gateway/AP/Ok
Reset: No
Setup Using: by default, + usb nas samba & dlna
Issues/Errors: Yes, Samba, - 2 of 3 EXT4 drives not connect to Windows 10, asking for login and password that is not set in router\nas tab.
I have to roll back to r45735.
2 of 3 EXT4 drives not connect to Windows 10, asking for login and password that is not set in router\nas tab.
Did you disconnect and boot into a linux computer to run e2fsck? For others with NTFS run chkdsk to clean.
I have the same issue with my broadcom. I have 'cleaned' the drive, it mounts. I can see the files from my television but cannot access them from Win7 using explorer
2 of 3 EXT4 drives not connect to Windows 10, asking for login and password that is not set in router\nas tab.
Did you disconnect and boot into a linux computer to run e2fsck? For others with NTFS run chkdsk to clean.
Personally me, - I was not do it, but in previous upper post are proofing that the problem is not on HDDs. On build 45735 or on 44715 that my r7800 was running, there's no problems at all with access to HDDs.
Joined: 08 May 2018 Posts: 14224 Location: Texas, USA
Posted: Tue Feb 23, 2021 23:28 Post subject:
Not sure if the EXT* filesystem drives are having the same issue as NTFS (that is ntfs3 driver-related), but it wouldn't hurt to run a filesystem check on them.
Router/Version: R7800
File/Kernel: dd-wrt-webupgrade-netgear_r7800-r45820.bin
Previous/Reset: dd-wrt-webupgrade-netgear_r7800-r45767.bin / no reset
Mode/Status: WDS with 4 stations
Issues/Errors: uptime 5 hours - OK so far
Not sure if the EXT* filesystem drives are having the same issue as NTFS (that is ntfs3 driver-related), but it wouldn't hurt to run a filesystem check on them.
@Abboo: Does Win7 even support the newer ntfs3 linux driver?
I could not access the shared network folder with Win7 with the previous build either.
Joined: 21 Nov 2013 Posts: 65 Location: Cathedral City, CA, USA
Posted: Wed Feb 24, 2021 0:47 Post subject:
Abboo wrote:
blkt wrote:
al_bo wrote:
2 of 3 EXT4 drives not connect to Windows 10, asking for login and password that is not set in router\nas tab.
Did you disconnect and boot into a linux computer to run e2fsck? For others with NTFS run chkdsk to clean.
I have the same issue with my broadcom. I have 'cleaned' the drive, it mounts. I can see the files from my television but cannot access them from Win7 using explorer
Router/Version: r7800 / DD-WRT v3.0-r45820 std (02/23/21) File/Kernel: Linux 4.9.257 #1157 SMP Tue Feb 23 02:37:39 +07 2021 armv7l Previous/Reset: r45767 / No Reset Mode/Status: Working / ksmbd maybe issue Issues/Errors: Cannot get to shares
Greetings,
Running into issues accessing shares from a Win10 system to USB drive connected to r7800. When browsing through network neighborhood, when I click on Router's icon it prompts for username and password, which there shouldn't be any. I also have share "mapped" to same location. I checked out the file smb.conf and noticed that the shares had an extra "/" similar to this: *** NOTE *** whole USB drive formatted EXT4 and check with e2fsck
force user = root
[Video]
comment = Video
path = /mnt/data//video
read only = no
guest ok = yes
force user = root
[opt]
comment = opt
path = /opt/
read only = no
guest ok = yes
I went into the web interface SERVICES/NAS and removed all the starting "/" from the "subdir" boxes (example: /video = video), note these "/" in subdir were always there with previous firmware versions. I was able to browse and use the files in "mapped" drive, which maps to /mnt/data, this share pre-existed before this firmware upgrade on win10. Browsing through network neighborhood still brings up username/password box, and nothing works there. And trying to add a share in win10, it will prompt for name/password. Once I removed the extra "/" I was able to browse the preexisting mapped share.
Error in the logfile shows this each time trying to access.
Feb 23 16:25:23 PANDA-WRT-1 local5.err ksmbd: [ksmbd-worker/4144]: ERROR: treecon: user account not found:
Full smb.conf [global] section
[global]
log level = 1
netbios name = PANDA-WRT-1
server string = PANDA-SAMBA %h
syslog = 10
encrypt passwords = true
preferred master = yes
use sendfile = yes
aio read size = 2048
aio write size = 2048
large readwrite = yes
security = user
oplocks = yes
mangled names = no
max stat cache size = 64
workgroup = MSHOME
bind interfaces only = yes
guest account = nobody
map to guest = Bad User
smb passwd file = /var/samba/smbpasswd
private dir = /var/samba
passdb backend = smbpasswd
log file = /var/smbd.log
max log size = 1000
socket options = TCP_NODELAY IPTOS_LOWDELAY SO_SNDBUF=262144 SO_RCVBUF=262144
read raw = yes
write raw = yes
max xmit = 65536
dead time = 15
getwd cache = yes
lpq cache time = 30
server min protocol = SMB2_02
server max protocol = SMB3_11
printing = none
load printers = No
usershare allow guests = Yes
smb3 encryption = yes
Maybe extra "/" somewhere causing the problem as the username and password will popup if asking for a share that is misspelled, using an uppercase when lowercase needed, or share does not exist.
Thanks for the wonderful firmware BS, and to the many people who make this firmware the best. _________________ Router/Version: Netgear R7800
File/Kernel: DD-WRT v3.0-r50671 std (10/26/22), Linux 4.9.330 #1313 SMP Wed Oct 26 05:13:03 +07 2022 armv7l
Joined: 06 Jun 2006 Posts: 7492 Location: Dresden, Germany
Posted: Wed Feb 24, 2021 7:35 Post subject:
by default the subdir box is empty and does not contain a "/". so you entered it already in your config and its indeed wrong if you enter a leading /
its named subdir and subdir is just a directory name where a leading slash indicates root _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
