New Build - 02-04-2021-r45677

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Atheros WiSOC based Hardware
Goto page 1, 2  Next
Author Message
kernel-panic69
DD-WRT Guru


Joined: 08 May 2018
Posts: 9023
Location: Texas, USA

PostPosted: Thu Feb 04, 2021 15:31    Post subject: New Build - 02-04-2021-r45677 Reply with quote
[WARNING]: This thread is only for feedback on this beta release for developers and the community's benefit.
DO NOT flash this beta release unless you understand the risks involved and device specific recovery methods.
Avoid discussions! Create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.


Downloads: (DD-WRT website) HTTPS & FTP (try another if a link does not work)

CLI Flash: 'cd /tmp' then 'wget {file URL}' (or 'curl -k {file URL} -o {file}') with http (not https) or ftp. Then 'write {file} linux'.

Repository: Trac SVN changelog since last build r45667 (GitHub mirror)

Notes:
OpenVPN version 2.5.0 and Guides
WireGuard 1.0.20200908/Tools: Guides, PBR, Kill Switch, Inbound Firewall, Naming of Peers, Status, Key. Thanks BS & egc!
• CVE-2019-14899 VPN fix (applicability depends on VPN setup) and GUI toggle since r41813.
In-kernel Samba (ksmbd 3.3.4): default min/max versions changed with WSD support, ANTFS & NTFS3 kernel mode drivers.
• Dnsmasq version 2.84 release with r45632 (2.83 at r45563, prerelease since r45036).

Issues:
• There may be remaining issues for Samba.

Important:
• For issues provide applicable info: 'dmesg', 'cat /tmp/var/log/messages', syslog, klog, serial, strace, tcpdump, wireshark etc.
• Any firewall NAT or WAN issues, show output: 'iptables -vnL', 'iptables -t nat -vnL', 'iptables -t mangle -vnL' and /tmp/.ipt file.
• Search SVN tickets & discuss in forum before opening. Before reporting: reset & manually set up, not restore from a backup.
• Please include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) & relevant configuration information.

Example Template:
Code:
[b]Router/Version: [/b]
[b]File/Kernel: [/b]
[b]Previous/Reset: [/b]
[b]Mode/Status: [/b]
[b]Issues/Errors: [/b]

_________________
Official Forum Rules, Guidelines & Helpful InformationFirmware FAQInstallation WikiWhere Do I Download Firmware?
DON'T use Chromium-based browsersRTFM/STFW TL;DR is NOT an excuse. • Why Should I Care What Color the Bikeshed Is?
Please DO NOT PM me with questions; Ask in the forum. ---------------------- Linux User #377467 counter.li.org / linuxcounter.net


Last edited by kernel-panic69 on Thu Feb 04, 2021 21:04; edited 1 time in total
Sponsor
MLandi
DD-WRT User


Joined: 04 Dec 2007
Posts: 424

PostPosted: Thu Feb 04, 2021 16:04    Post subject: Reply with quote
Update method: SSH
Router/Version: Netgear R9000 Nighthawk X10
File/Kernel: DD-WRT v3.0-r45677 std (02/04/21)
Previous/Reset: DD-WRT v3.0-r45667 std (02/03/21) / No
Mode/Status: Gateway / Working Normally / Clock 2000MHz
Issues/Errors: None

_________________
Netgear R9000 X10
DD-WRT v3.0-r46979 std (06/21/21)
Gateway, AP, DNSMasq
IPv4 & IPv6 (Prefix Delegation)
CloudFlare, Ignore WAN DNS
QoS Disabled
Vanilla
Static Leases & DHCP
2.4GHz: 10 + 6 (2457 MHz HT40), ACK Timing 450
5GHz: 100 + 114 (5500 MHz VHT160), ACK Timing 450
Clock 2000MHz
Xfinity 1.2Gbps/42Mbps
mrjcd
DD-WRT Guru


Joined: 31 Jan 2015
Posts: 5431
Location: Texas

PostPosted: Thu Feb 04, 2021 16:32    Post subject: Reply with quote
Linksys EA8500 ... main gateway
Firmware Version DD-WRT v3.0-r45677 std (02/04/21)
Kernel VersionLinux 4.9.254 #1096 SMP Thu Feb 4 01:54:28 +07 2021 armv7l
GUI install over r45667...NO reset
all worky good

#

Netgear WNDR3700 V4
DD-WRT v3.0-r45677 std (02/04/21)
Linux 3.18.140-d5 #105514 Thu Feb 4 07:07:47 +06 2021 mips
GUI install over r45667...NO reset
all ok
giuliomagnifico
DD-WRT User


Joined: 11 Apr 2016
Posts: 377
Location: Italy

PostPosted: Thu Feb 04, 2021 20:19    Post subject: Reply with quote
R7800 here, updated via ssh, this build finally fixed my AirPrint printer, now it works again, in the last 2/3 build it was unable to connect to my router, I haven't investigated in deep why.

Thanks a lot BS Arrow
tatsuya46
DD-WRT Guru


Joined: 03 Jan 2010
Posts: 7486
Location: YWG, Canada

PostPosted: Thu Feb 04, 2021 20:24    Post subject: Reply with quote
Router Model: dir-862L(x2), wndr4300, x86_64(2x qca9984 ,1x qca9882)

Status: it runs
Reset: no
Errors: see tickets below

https://svn.dd-wrt.com/ticket/5225 *
https://svn.dd-wrt.com/ticket/5603 *
https://svn.dd-wrt.com/ticket/5848
https://svn.dd-wrt.com/ticket/5938
https://svn.dd-wrt.com/ticket/6286
https://svn.dd-wrt.com/ticket/6315
https://svn.dd-wrt.com/ticket/6481 *
https://svn.dd-wrt.com/ticket/6495 *
https://svn.dd-wrt.com/ticket/6655
https://svn.dd-wrt.com/ticket/6842
https://svn.dd-wrt.com/ticket/6903 *
https://svn.dd-wrt.com/ticket/6921
https://svn.dd-wrt.com/ticket/7154
https://svn.dd-wrt.com/ticket/7222 *
https://svn.dd-wrt.com/ticket/7226
https://svn.dd-wrt.com/ticket/7246
https://svn.dd-wrt.com/ticket/7284
https://svn.dd-wrt.com/ticket/7331
https://svn.dd-wrt.com/ticket/7334 *


broken build, several routers no wan ip.

and what are the odds its from

https://svn.dd-wrt.com/changeset/45670
https://svn.dd-wrt.com/changeset/45676

_________________
LATEST FIRMWARE(S)

BrainSlayer wrote:
we just do it since we do not like any restrictions enforced by stupid cocaine snorting managers

[x86_64] Haswell i3-4150/QCA9984/QCA9882 ------> r46979 std
[QUALCOMM] DIR-862L --------------------------------> r46979 std
[QUALCOMM] DIR-862L --------------------------------> r46979 std
▲ ACTIVE / INACTIVE ▼
[QUALCOMM] WNDR4300 v1 --------------------------> r46350 std
[BROADCOM] DIR-860L A1 ----------------------------> r46329 std


If you use DSLReports please enable hi-res bufferbloat.


Sigh.. why do i exist anyway..
Skrumpy
DD-WRT Novice


Joined: 02 Feb 2021
Posts: 11

PostPosted: Thu Feb 04, 2021 21:00    Post subject: Reply with quote
Update method: Web upgrade (Firefox)
[b]Router/Version: Netgear R9000 Nighthawk X10
File/Kernel:[/b] DD-WRT v3.0-r45677 std (02/04/21)
Previous/Reset: DD-WRT v3.0-r45667 std (02/03/21) / No
Mode/Status: Gateway (using pi-hole DHCP) / Wireless 5GHz/2.4GHz / Working Normally / Clock 2000MHz
Issues/Errors: None so far. The set clock speed retained my 2000MHz overclock as shown on Status page. Base temps increased, so assuming that it is accurate. Thanks gents!
abhijitat
DD-WRT User


Joined: 06 Feb 2020
Posts: 131
Location: Maharashtra, India

PostPosted: Fri Feb 05, 2021 7:57    Post subject: Reply with quote
Router/Version: Netgear R7800
Firmware: DD-WRT v3.0-r45677 std (02/04/21)
Kernel: Linux 4.9.254 #1098 SMP Thu Feb 4 02:51:40 +07 2021 armv7l
File/Upload: dd-wrt-webupgrade.bin / Upload using SSH
Mode: Gateway/AP
Reset: No
Previous: DD-WRT v3.0-r45667 std (02/03/21)
Setup Using: PPPOE, 2.4 GHz, 5.0 GHz, IPv4, DNSMasq, USB, NTP TimeSync, wireguard
Status: Working Fine, since build 45667, the cpu usage has reduced drastically as the cpu temperature. just to ensure, tried 45632 and cpu temperature was higher by around 5-6 degrees.


Thank you BrainSlayer for Wonderful firmware.

Thanks all Guru for your help in forums.
egorenar
DD-WRT Novice


Joined: 26 Dec 2019
Posts: 30

PostPosted: Fri Feb 05, 2021 11:25    Post subject: Reply with quote
Update: TFTP recovery mode
Works with no problems so far.

_________________
Netgear R9000
-------------------------------------------------------------
Firmware: DD-WRT v3.0-r45767 std (02/17/21)
Overclocking Frequency 1700 MHz
-------------------------------------------------------------
2.4 GHz - Disabled
5 GHz VHT80 AC/N-Mixed Channel 100 UU(+6)
ACK Timing 450, Tx Power 30dbm
SU Beamforming ON, MU Beamforming OFF, U-APSD ON
Protection Mode RTS/CTS, RTS Threshold 784
Beacon Interval 300, DTIM Interval 2
-------------------------------------------------------------
External USB3 drive (extra PSU) + Entware
VPN client, dnsmasq, samba(Entware), nginx, znc
ArjenR49
DD-WRT User


Joined: 05 Oct 2008
Posts: 418
Location: Helsinki, Finland

PostPosted: Fri Feb 05, 2021 11:50    Post subject: Reply with quote
Router R7800 upgraded from previous build using the GUI function. No reset.

Running fine since this build came online, before it was even announced on this forum.

No problems except this:

When restarting a connected laptop the active client table picks up a temporary IP address (169.x.y.z) for this client and keeps it listed along with the final (reserved) IP of the client.

Then whenever there are those 2 IP's behind the name of the client in the active clients table the number of connections for this client is given as 0 (ZERO), which in general is incorrect (checked from Active IP connections table).

Rebooting the router and the client while having them disconnected from eachother and only reconnecting the ethernet cable when both devices are up and running, prevents the temporary IP (169.x.y.z) from being included in the active clients table data, in which case the number of connections is shown normally.

This bug(?) has been present in all the latest builds.
chromoxdor
DD-WRT Novice


Joined: 02 Dec 2014
Posts: 22

PostPosted: Fri Feb 05, 2021 12:03    Post subject: Reply with quote
Router/Version: TP-Link Archer C7 V2
File/Kernel: Linux 3.18.140-d5 #105492 Thu Feb 4 06:13:15 +06 2021 mips
Previous/Reset: r45592 / yes
Mode/Status: Client on 5GHz AC/N-Mixed (wlan1); AP N/G mixed (wlan0); VAP (wlan1.1)
Issues/Errors:

Still having issues with the wifi since r45563.
It seems to be only happen on wlan1.1 .
There are now no reconnections any more.
The client stays connected but sometimes the traffic stops for a minute and after that is works again (not so on wlan0) and sometimes i have to reconnect the wifi to get traffic again. The router is also inaccessible from the client when it hangs.

Al this happens randomly(i guess) and about twice an hour


There is still nothing special in the Syslog showing up

Code:
Feb 5 12:02:27 tpac7 daemon.info ntpclient[31049]: Time set from 2.pool.ntp.org [195.242.98.57].
Feb 5 12:02:27 tpac7 daemon.info process_monitor[25522]: cyclic NTP Update success


This is the latest syslog entry und at 12:50 it was hanging until i reconnected the client(my computer)

Edit: I am not sure but my clients for streaming video don’t have the problem while they stream.
So maybe it is something like a timeout.... just guessing
mrjcd
DD-WRT Guru


Joined: 31 Jan 2015
Posts: 5431
Location: Texas

PostPosted: Sat Feb 06, 2021 23:00    Post subject: Reply with quote
EA8500 went back to r44786 cause r45677 is shit for 2.4 devices
rolffokkens
DD-WRT Novice


Joined: 23 Jan 2021
Posts: 7

PostPosted: Sun Feb 07, 2021 11:45    Post subject: Reply with quote
Router/Version: TP-Link ARCHER-C7/v5
File/Kernel: DD-WRT v3.0-r45677 std (02/04/21)/Linux 3.18.140-d5 #105496 Thu Feb 4 06:23:50 +06 2021 mips
Previous/Reset: DD-WRT v3.0-r45632 std (01/31/21)/No
Mode/Status: AP multi SSD/VLAN/Working Normally
Issues/Errors: Some:

- Whenever "Channel Width" is set, the Wifi channel seems to drop from the radar (no longer visible using iPhone), applies for both channels. Note: in previous releases this worked fine, although it did not apply for the virtual interfaces.

- As reported earlier, the pvid (as shown in swconfig) always defaults to the highest VLAN as set in the UI. This makes it impossible to have VLAN1 untagged on a tagged interfaces.

- Possibly solved issue: Earlier releases seemed to lose 5GHz Wifi contact with a device: the device did not notice, but in the DD-WRT UI it was no longer present. Net effect result was no useful connection though. This issue has not popped up however in r45677 - yet.
volvy
DD-WRT Novice


Joined: 18 Mar 2017
Posts: 26
Location: USA

PostPosted: Sun Feb 07, 2021 17:31    Post subject: Reply with quote
Quote:
mrjcd
PostPosted: Sun Feb 07, 2021 3:00 Post subject:
EA8500 went back to r44786 cause r45677 is shit for 2.4 devices


That interesting, I can't get the WebUI to load properly from any 2.4 connected device, but all the 2.4 connected devices have perfectly fine network access. WebUI is loading great from 5Ghz and from wired connections. Same issue in r45690. Been playing with the 2.4 advanced settings to see if the problem is there, but no luck.
mrjcd
DD-WRT Guru


Joined: 31 Jan 2015
Posts: 5431
Location: Texas

PostPosted: Sun Feb 07, 2021 17:47    Post subject: Reply with quote
volvy wrote:
Quote:
mrjcd
PostPosted: Sun Feb 07, 2021 3:00 Post subject:
EA8500 went back to r44786 cause r45677 is shit for 2.4 devices


That interesting, I can't get the WebUI to load properly from any 2.4 connected device, but all the 2.4 connected devices have perfectly fine network access. WebUI is loading great from 5Ghz and from wired connections. Same issue in r45690. Been playing with the 2.4 advanced settings to see if the problem is there, but no luck.

2.4 with this biuild would drop on some of my devices at random.
ALSO was unable to access the routers SAMBA share with 2.4 devices so it is shit for me Evil or Very Mad
volvy
DD-WRT Novice


Joined: 18 Mar 2017
Posts: 26
Location: USA

PostPosted: Sun Feb 07, 2021 18:16    Post subject: Reply with quote
Quote:
mrjcd 2.4 with this biuild would drop on some of my devices at random.
ALSO was unable to access the routers SAMBA share with 2.4 devices so it is shit for me.


I don't run SAMBA, but I've had no issues with dropped devices that I've noticed. Initially I used NG-Mixed, but had to change to Mixed to get Android and Apple devices to connect. With r44786 everything worked fine for me. And that was the first version I used when I installed DD-wrt using your very nice guide last month. I updated past r44786 mostly to get dnsmasq updates.
Goto page 1, 2  Next Display posts from previous:    Page 1 of 2
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Atheros WiSOC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum