Joined: 08 May 2018 Posts: 14217 Location: Texas, USA
Posted: Thu Feb 04, 2021 15:31 Post subject: New Build - 02-04-2021-r45677
[WARNING]: This thread is only for feedback on this beta release for developers and the community's benefit.
DO NOT flash this beta release unless you understand the risks involved and device specific recovery methods.
Avoid discussions! Create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues:
• There may be remaining issues for Samba.
Important:
• For issues provide applicable info: 'dmesg', 'cat /tmp/var/log/messages', syslog, klog, serial, strace, tcpdump, wireshark etc.
• Any firewall NAT or WAN issues, show output: 'iptables -vnL', 'iptables -t nat -vnL', 'iptables -t mangle -vnL' and /tmp/.ipt file.
• Search SVN tickets & discuss in forum before opening. Before reporting: reset & manually set up, not restore from a backup.
• Please include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) & relevant configuration information.
Linksys EA8500... main gateway
Firmware Version DD-WRT v3.0-r45677 std (02/04/21)
Kernel VersionLinux 4.9.254 #1096 SMP Thu Feb 4 01:54:28 +07 2021 armv7l
GUI install over r45667...NO reset
all worky good
#
Netgear WNDR3700 V4
DD-WRT v3.0-r45677 std (02/04/21)
Linux 3.18.140-d5 #105514 Thu Feb 4 07:07:47 +06 2021 mips
GUI install over r45667...NO reset
all ok
R7800 here, updated via ssh, this build finally fixed my AirPrint printer, now it works again, in the last 2/3 build it was unable to connect to my router, I haven't investigated in deep why.
Update method: Web upgrade (Firefox)
[b]Router/Version: Netgear R9000 Nighthawk X10
File/Kernel:[/b] DD-WRT v3.0-r45677 std (02/04/21)
Previous/Reset: DD-WRT v3.0-r45667 std (02/03/21) / No
Mode/Status: Gateway (using pi-hole DHCP) / Wireless 5GHz/2.4GHz / Working Normally / Clock 2000MHz
Issues/Errors: None so far. The set clock speed retained my 2000MHz overclock as shown on Status page. Base temps increased, so assuming that it is accurate. Thanks gents!
Joined: 06 Feb 2020 Posts: 167 Location: Maharashtra, India
Posted: Fri Feb 05, 2021 7:57 Post subject:
Router/Version: Netgear R7800
Firmware: DD-WRT v3.0-r45677 std (02/04/21)
Kernel: Linux 4.9.254 #1098 SMP Thu Feb 4 02:51:40 +07 2021 armv7l
File/Upload: dd-wrt-webupgrade.bin / Upload using SSH
Mode: Gateway/AP
Reset: No Previous: DD-WRT v3.0-r45667 std (02/03/21)
Setup Using: PPPOE, 2.4 GHz, 5.0 GHz, IPv4, DNSMasq, USB, NTP TimeSync, wireguard
Status: Working Fine, since build 45667, the cpu usage has reduced drastically as the cpu temperature. just to ensure, tried 45632 and cpu temperature was higher by around 5-6 degrees.
Joined: 05 Oct 2008 Posts: 666 Location: Helsinki, Finland / nr. Alkmaar, Netherlands
Posted: Fri Feb 05, 2021 11:50 Post subject:
Router R7800 upgraded from previous build using the GUI function. No reset.
Running fine since this build came online, before it was even announced on this forum.
No problems except this:
When restarting a connected laptop the active client table picks up a temporary IP address (169.x.y.z) for this client and keeps it listed along with the final (reserved) IP of the client.
Then whenever there are those 2 IP's behind the name of the client in the active clients table the number of connections for this client is given as 0 (ZERO), which in general is incorrect (checked from Active IP connections table).
Rebooting the router and the client while having them disconnected from eachother and only reconnecting the ethernet cable when both devices are up and running, prevents the temporary IP (169.x.y.z) from being included in the active clients table data, in which case the number of connections is shown normally.
This bug(?) has been present in all the latest builds.
Router/Version: TP-Link Archer C7 V2
File/Kernel: Linux 3.18.140-d5 #105492 Thu Feb 4 06:13:15 +06 2021 mips
Previous/Reset: r45592 / yes
Mode/Status: Client on 5GHz AC/N-Mixed (wlan1); AP N/G mixed (wlan0); VAP (wlan1.1)
Issues/Errors:
Still having issues with the wifi since r45563.
It seems to be only happen on wlan1.1 .
There are now no reconnections any more.
The client stays connected but sometimes the traffic stops for a minute and after that is works again (not so on wlan0) and sometimes i have to reconnect the wifi to get traffic again. The router is also inaccessible from the client when it hangs.
Al this happens randomly(i guess) and about twice an hour
There is still nothing special in the Syslog showing up
Code:
Feb 5 12:02:27 tpac7 daemon.info ntpclient[31049]: Time set from 2.pool.ntp.org [195.242.98.57].
Feb 5 12:02:27 tpac7 daemon.info process_monitor[25522]: cyclic NTP Update success
This is the latest syslog entry und at 12:50 it was hanging until i reconnected the client(my computer)
Edit: I am not sure but my clients for streaming video don’t have the problem while they stream.
So maybe it is something like a timeout.... just guessing
Router/Version: TP-Link ARCHER-C7/v5
File/Kernel: DD-WRT v3.0-r45677 std (02/04/21)/Linux 3.18.140-d5 #105496 Thu Feb 4 06:23:50 +06 2021 mips
Previous/Reset: DD-WRT v3.0-r45632 std (01/31/21)/No
Mode/Status: AP multi SSD/VLAN/Working Normally
Issues/Errors: Some:
- Whenever "Channel Width" is set, the Wifi channel seems to drop from the radar (no longer visible using iPhone), applies for both channels. Note: in previous releases this worked fine, although it did not apply for the virtual interfaces.
- As reported earlier, the pvid (as shown in swconfig) always defaults to the highest VLAN as set in the UI. This makes it impossible to have VLAN1 untagged on a tagged interfaces.
- Possibly solved issue: Earlier releases seemed to lose 5GHz Wifi contact with a device: the device did not notice, but in the DD-WRT UI it was no longer present. Net effect result was no useful connection though. This issue has not popped up however in r45677 - yet.
mrjcd
PostPosted: Sun Feb 07, 2021 3:00 Post subject:
EA8500 went back to r44786 cause r45677 is shit for 2.4 devices
That interesting, I can't get the WebUI to load properly from any 2.4 connected device, but all the 2.4 connected devices have perfectly fine network access. WebUI is loading great from 5Ghz and from wired connections. Same issue in r45690. Been playing with the 2.4 advanced settings to see if the problem is there, but no luck.
mrjcd
PostPosted: Sun Feb 07, 2021 3:00 Post subject:
EA8500 went back to r44786 cause r45677 is shit for 2.4 devices
That interesting, I can't get the WebUI to load properly from any 2.4 connected device, but all the 2.4 connected devices have perfectly fine network access. WebUI is loading great from 5Ghz and from wired connections. Same issue in r45690. Been playing with the 2.4 advanced settings to see if the problem is there, but no luck.
2.4 with this biuild would drop on some of my devices at random.
ALSO was unable to access the routers SAMBA share with 2.4 devices so it is shit for me
mrjcd 2.4 with this biuild would drop on some of my devices at random.
ALSO was unable to access the routers SAMBA share with 2.4 devices so it is shit for me.
I don't run SAMBA, but I've had no issues with dropped devices that I've noticed. Initially I used NG-Mixed, but had to change to Mixed to get Android and Apple devices to connect. With r44786 everything worked fine for me. And that was the first version I used when I installed DD-wrt using your very nice guide last month. I updated past r44786 mostly to get dnsmasq updates.
