Posted: Wed Feb 03, 2021 14:42 Post subject: New Build - 02/03/2021 - r45667
[WARNING]: This thread is only for feedback on this beta release for developers and the community's benefit.
DO NOT flash this beta release unless you understand the risks involved and device specific recovery methods.
Avoid discussions! Create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues:
• There may be remaining issues for Samba.
Important:
• For issues provide applicable info: 'dmesg', 'cat /tmp/var/log/messages', syslog, klog, serial, strace, tcpdump, wireshark etc.
• Any firewall NAT or WAN issues, show output: 'iptables -vnL', 'iptables -t nat -vnL', 'iptables -t mangle -vnL' and /tmp/.ipt file.
• Search SVN tickets & discuss in forum before opening. Before reporting: reset & manually set up, not restore from a backup.
• Please include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) & relevant configuration information.
Update method: Web upgrade (Firefox)
Router/Version: Netgear R9000 Nighthawk X10
File/Kernel: DD-WRT v3.0-r45667 std (02/03/21)
Previous/Reset: DD-WRT v3.0-r45632 std (01/31/21) / No
Mode/Status: Gateway (using pi-hole DHCP) / Wireless 5GHz/2.4GHz / Working Normally / Clock 2000MHz
Issues/Errors: For some reason clock frequency reset back to 1700MHz upon update. I reset to 2000MHz which is what is shown in Administration>Management but Status page shows CPU clock at 1700MHz.
I had tried that before, but just tried a few more times. Also tried other clock speeds (1900, 1800, etc). Save, Apply, Reboot and also tried power off reset. No dice. The Management page states the saved value, but the status page retains the 1700MHz regardless of what is set. Also cleared cache and tried a different browser, just to ensure it wasn't just keeping the value.
I had tried that before, but just tried a few more times. Also tried other clock speeds (1900, 1800, etc). Save, Apply, Reboot and also tried power off reset. No dice. The Management page states the saved value, but the status page retains the 1700MHz regardless of what is set. Also cleared cache and tried a different browser, just to ensure it wasn't just keeping the value.
Linksys EA8500... main gateway
DD-WRT v3.0-r45667 std (02/03/21)
Linux 4.9.254 #1092 SMP Wed Feb 3 01:59:01 +07 2021 armv7l
GUI install over r45632 -- NO reset
all ok
#
Netgear WNDR3700 V4
DD-WRT v3.0-r45667 std (02/03/21)
Linux 3.18.140-d5 #105379 Wed Feb 3 06:11:43 +06 2021 mips
GUI install over r45632 -- NO reset
all ok
Router/Version: R7800
Firmware: DD-WRT v3.0-r45667 std (02/03/21)
Kernel: Linux 4.9.254 #1094 SMP Wed Feb 3 04:53:29 +07 2021 armv7l
Previous: DD-WRT v3.0-r45632 std (01/31/21)
Mode/Status: Gateway/AP/Ok
Reset: No
Setup Using: 2.4 GHz, 2.4 GHz guest (VAP), 5.0 GHz, IPv4, DNSMasq, Port Forwarding, USB, NAS, Samba NTFS, NTP, VNC Repeater, PPTP, and Wake-on-WAN (internet)
Issues/Errors: Yes, PPTP will not connect from the Internet (WAN) to the PPTP server, but will connect from the LAN. Not sure which release this started as it’s seldom used. _________________ Netgear XR500, R7800
Asus AC87Ua1
Repeater Bridge
Netgear R6400v2otp
Status: Up and running for 8 hours, basic setup as Gateway, static leases, OpenVPN client and
OpenVPN server working, WireGuard client and Server working, NAS and Samba working, NTFS working fine with the new Paragon driver
Wifi functions really good so far, QOS looking good too.
errors: cant keep samba running - seems to crash when my mac disconnects the share , after that it pops up login but doesnt work unless i restart the service