Issues - disconnects, only noticed while using streaming services. Roku disconnected, Twitch disconnected. Twitch machine uses Killer wireless. Not sure whats in the Roku 3.
previous was 44467.
Just rolled forward, will post after a few days to that build thread.
There have been problems with some clients especially intel, it has been reported and BS has been working on it, so it might be better on the latest build
This morning I upped from r44483 to r44772 which has been the last "good" version for me, and everything WiFi-wise is still ok. Time permitting, I'll check the latest build over the weekend.
So, for me, WiFi started acting weirdly when updating from r44772 to r44849 (I never tested r44809).
Last edited by Molle on Fri Nov 27, 2020 12:16; edited 3 times in total
Router/Version: r7800 File/Kernel: Linux 4.9.242 #836 SMP Fri Nov 20 20:41:15 +07 2020 armv7l Previous/Reset: r40270m kongat (07/11/2019); No reset Mode/Status: Working; Up 6hrs Issues/Errors: Minor
I've been seeing Receive RX errors on mostly the 5ghz radio with both previous kong build and this build. kong build was almost always over 60k in RX errors over about 20 days and this build so far just over 4,500 RX errors. I have only 4 devices on the 5gz radio; 2 android phones, one kindle, and one smart (samsung) tv.
Also, the 5gh speed is much slower than the kongat build; kongat my phone (s9) was getting about 450Mbs and now it's about 150-220Mbs. _________________ Netgear R7800: DD-WRT v3.0-r47822 std (12/09/21)
Linksys wrt1900acsV2: DD-WRT v3.0-r47822 std (12/09/21)
Posted: Wed Dec 30, 2020 22:18 Post subject: Web interface troubles
Router/Version: Netgear R7800
Firmware: DD-WRT v3.0-r44849 std (11/20/20)
File/Upload: Web UI
Mode: Router
Reset: No
2.4 GHz N only
I have an interesting issue.. I have a WDS config, the main router is a R9000 and the STA is a R7800. It is all working just fine with the exception of accessing the web interface of the R7800 while connected to the R7800. Most of the time I cannot access it.. the page will not load. I will sometimes get a black screen, sometimes a while screen.. and SOMETIMES it will actually load up but then shortly after crap out again. It doesn't matter if I use http or https.
To be clear, this is ONLY an issue when I am directly connected to the WDS STA. If I connect via LAN or via my other wireless network I can access the web interface with no issues at all.
Is this a known issue? Any ideas as to how I could fix this?
I tried going to the latest build from yesterday and I was unable to save the wireless MAC for the WDS config. Every time I hit save the MAC would just disappear and would never save (I noticed the new builds changed to WLAN instead of ATH). This was the reason I reverted back to this build. Maybe I just need to find another build or is this fixable?
Posted: Wed Dec 30, 2020 23:27 Post subject: Re: Web interface troubles
Laithan wrote:
I have an interesting issue.. I have a WDS config, the main router is a R9000 and the STA is a R7800. It is all working just fine with the exception of accessing the web interface of the R7800 while connected to the R7800. Most of the time I cannot access it.. the page wil
I was seeing the same issue, R7800 WDS AP and R7500v2 WDS STA.
The R7500v2 GUI was nearly inaccessible when connected to it's radio
but worked fine if I was connected to the R7800 WDS AP.
I have reverted both back to 44715:44719 for the time being and all is well.
