Joined: 08 May 2018 Posts: 14244 Location: Texas, USA
Posted: Fri Dec 18, 2020 16:05 Post subject: New Build - 12-18-2020-r45036
[WARNING]: This thread is only for feedback on this beta release for developers and the community's benefit.
DO NOT flash this beta release unless you understand the risks involved and specific device recovery methods.
Avoid discussions! Create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• DNScrypt 1.95 can still be used in the GUI but v2 (not compatible) requires Golang and thus Entware. 6246
• WDS does not work on Broadcom ARM devices(only MIPS<->MIPS) & bridge modes on k4.4 devices may sometimes work in some configurations in certain builds but are not supported by the bcmdhd driver. Use client or repeater instead.
• VAPs not working at bootfixed for unbridged VAPs with r40564:40566.Workaround startup command:
sleep 10;stopservice nas;stopservice wlconf;startservice wlconf;startservice nas(there are a few alternatives, search).
• If start-up scripts do not work from USB add a delay (e.g. wait script or 'sleep 25').
• For Broadcom ARM devices missing 5GHz channels, via telnet/ssh: 'nvram set brcm_unlock=1' 'nvram commit' 'nvram reboot'
Important:
• If reporting issues provide applicable info: 'dmesg', 'cat /tmp/var/log/messages', syslog, serial output, strace, tcpdump etc.
• For firewall NAT or WAN issues provide 'iptables -vnL', 'iptables -t nat -vnL', 'iptables -t mangle -vnL' and the /tmp/.ipt file.
• Search existing SVN tickets before opening a new one. Before reporting, reset and manually setup (no nvram backup).
• Be sure to include operating and wireless modes (Gateway, AP, CB, etc.) along with relevant configuration information.
Router/Version: Asus RT-N18U
Firmware: DD-WRT v3.0-r45036 std (12/18/20)
Kernel: Linux 4.4.248 #1590 Fri Dec 18 09:31:31 +07 2020 armv7l
Mode: Gateway
Previous: r44980
Reset: No
Status: Working
Issues: Yes
It looks like Status > LAN > Active Clients does not update correctly anymore.
Devices stay in active clients list even after being disconnected for long time.
Router: Netgear WNDR4500v2
File/Kernel: .bin - Linux 4.4.248 #5487 Fri Dec 18 17:53:17 +07 2020 mips
Mode/Status: Client+AP+VAP, no reset upgrade from 44481 (k4.4.237)... going back to gateway mode
Router: Netgear WNDR4000
File/Kernel: nv64k - Linux 4.4.248 #5503 Fri Dec 18 18:13:15 +07 2020 mips
Mode/Status: CB+AP+VAP, no reset upgrade from 42803 (k3.10.108)...moving to client mode
Updating these to set up for a work colleague whose family moved from an apartment to a house. The tiny ol' DIR-810L doesn't have the best coverage. _________________ #NAT/SFE/CTF: limited speed w/ DD#Repeater issues#DD-WRT info: FAQ, Builds, Types, Modes, Changes, Demo#
OPNsense x64 5050e ITX|DD: DIR-810L, 2*EA6900@1GHz, R6300v1, RT-N66U@663, WNDR4000@533, E1500@353,
WRT54G{Lv1.1,Sv6}@250|FreshTomato: F7D8302@532|OpenWRT: F9K1119v1, RT-ACRH13, R6220, WNDR3700v4
Router: Asus RT-AC68U
File Flashed: asus_rt-ac68u-firmware.trx
Firmware: 12/18/20 -r45036
Previous: kong r40270M
Reset: Yes (nvram erased)
Mode: Wireless Client/AP
Errors: No, works good so far.
Uptime: 1 hour, 45 min.
Client/Gateway on 5Ghz, AP on 2.4Ghz, DHCP. (Dual NAT)
Testing...
Many thanks to BS and those who run this forum for all the hard work you all put in! _________________ ASUS RT-AC3100 AP Merlin 386.12_4
ASUS RT-AC68U Media Bridge/Merlin 386.12_4 (x2)
ASUS RT-AC68U AP r54604
ASUS RT-AC68U Gateway/AP r54604
Edgerouter-4, v2.0.9-hotfix7
Joined: 16 Mar 2019 Posts: 353 Location: Szczecin, Poland EU
Posted: Sat Dec 19, 2020 18:39 Post subject: New Build - 12-18-2020-r45036
Router: Netgear WNR3500L v2
Kernel: Linux 4.4.248 #5487 Fri Dec 18 17:53:17 +07 2020 mips
Reset: No
Mode: Internet gateway, WIFI AP, dnsmasq server
Errors: Some errors and warnings in log
Status: Working
Uptime: more than 21 h
Problems in log:
Quote:
Jan 1 01:00:16 Myrouter kern.warn kernel: Found a AMD NAND flash with 2048B pages or 128KB blocks; total size 128MB
Jan 1 01:00:16 Myrouter kern.warn kernel: Primary instruction cache 32kB, 4-way, VIPT, I-cache aliases, linesize 32 bytes.
Jan 1 01:00:16 Myrouter kern.warn kernel: Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Jan 1 01:00:16 Myrouter kern.warn kernel: PCI: no core
Jan 1 01:00:16 Myrouter kern.warn kernel: PCI: no core
Jan 1 01:00:16 Myrouter kern.warn kernel: PCI: Fixing up bridge
Jan 1 01:00:16 Myrouter kern.warn kernel: PCI: Fixing up bus 0
Jan 1 01:00:16 Myrouter kern.err kernel: pflash: found no supported devices
Jan 1 01:00:16 Myrouter kern.warn kernel: ERROR: Unknown flash, device_id:0x00
Jan 1 01:00:16 Myrouter kern.err kernel: bcmsflash: found no supported devices
Jan 1 01:00:16 Myrouter kern.warn kernel: Boot partition size = 524288(0x80000)
Jan 1 01:00:16 Myrouter kern.warn kernel: lookup_nflash_rootfs_offset: offset = 0x500000
Jan 1 01:00:16 Myrouter kern.warn kernel: nf_conntrack_rtsp v0.7 loading
Jan 1 01:00:16 Myrouter kern.warn kernel: nf_nat_rtsp v0.7 loading
Jan 1 01:00:16 Myrouter kern.warn kernel: et: module license 'Proprietary' taints kernel.
Jan 1 01:00:16 Myrouter kern.warn kernel: Disabling lock debugging due to kernel taint
Jan 1 01:00:16 Myrouter kern.warn kernel: et_module_init: passivemode set to 0x0
Jan 1 01:00:16 Myrouter kern.warn kernel: et_module_init: txworkq set to 0x0
Jan 1 01:00:16 Myrouter kern.warn kernel: et_module_init: et_txq_thresh set to 0xce4
Jan 1 01:00:16 Myrouter kern.warn kernel: et_module_init: et_rxlazy_timeout set to 0x3e8
Jan 1 01:00:16 Myrouter kern.warn kernel: et_module_init: et_rxlazy_framecnt set to 0x20
Jan 1 01:00:16 Myrouter kern.warn kernel: et_module_init: et_rxlazy_dyn_thresh set to 0
Jan 1 01:00:16 Myrouter kern.warn kernel: eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 7.14.89.21 (r524987)
Jan 1 01:01:18 Myrouter daemon.err httpd[1459]: httpd : Request Error Code 401: Authorization required. please note that the default username is "root" in all newer releases
Dec 19 19:27:11 Myrouter daemon.err httpd[1459]: httpd : Request Error Code 401: Authorization required. please note that the default username is "root" in all newer releases
Device working rather good. I can't put own configuration in setup -> switch config tab. When I want to save new configuration and click save and then apply changes, configuration is back to default. This problem is for a long time. I don't know how to fix it.
The webUI for switch config on anything but Linksys WRT54* and E-series has always been 'broken' AFAIK. You have to fix it via command line and nvram settings. Even BrainSlayer has no idea what you're talking about. It also helps if you use the right browser without any extensions loaded in private / incognito mode separate from your regular internet traffic, with the cache cleared. _________________ "Life is but a fleeting moment, a vapor that vanishes quickly; All is vanity"
Contribute To DD-WRT Pogo - A minimal level of ability is expected and needed... DD-WRT Releases 2023 (PolitePol)
DD-WRT Releases 2023 (RSS Everything)
----------------------
Linux User #377467 counter.li.org / linuxcounter.net
Joined: 29 Sep 2020 Posts: 260 Location: United States
Posted: Sat Dec 19, 2020 20:46 Post subject:
Router/Version: Netgear R7000P
File/Kernel: netgear-r7000p-webflash.bin / Linux 4.4.248 #1592 SMP Fri Dec 18 09:45:16 +07 2020 armv7l
Previous/Reset: r45000 / no
Mode/Status: Gateway [AP 2.4 GHz] [AP 5 GHz] Unbound USB / working
Issues/Errors: no low 5 GHz channels. changing Regulatory Domains does not resolve the issue
'nvram set brcm_unlock=1' 'nvram commit' 'reboot' doesnt fix the issue either
in my experience R7000P users with low channels are doings so with remnants of a modified build
otherwise seems to be good
Last edited by itwontbewe on Wed Jan 13, 2021 18:25; edited 2 times in total
The webUI for switch config on anything but Linksys WRT54* and E-series has always been 'broken' AFAIK. You have to fix it via command line and nvram settings. Even BrainSlayer has no idea what you're talking about. It also helps if you use the right browser without any extensions loaded in private / incognito mode separate from your regular internet traffic, with the cache cleared.
In my opinion it's not problem with web browser. I have Firefox x64 in last stable version. I see that problem since provider renamed tab to switch config. I don't know why I can't configure ports. Have you got any ideas ?
Router/Version: Netgear R7000
File: netgear-r7000-webflash.bin
Firmware: DD-WRT v3.0-r45036 std (12/18/20) (prev. DD-WRT v3.0-r44970 std (12/11/20))
Kernel: Linux 4.4.248 #1586 SMP Thu Dec 17 11:37:24 +07 2020 armv7l
Mode: Gateway, Wifi disabled, Wireguard for external access, WAN to DSL, Keep Alive reboot 5:00 in the morning
Reset: No
Status: 0.5h up, ok.
Router/Version: Asus RT-N66U
File: dd-wrt.v24-45036_NEWD-2_K3.x-big-RT-N66U.trx
Firmware: DD-WRT v3.0-r45036 big (12/18/20) (prev. DD-WRT v3.0-r44970 big (12/11/20))
Kernel: Linux 4.4.248 #5499 Fri Dec 18 18:08:20 +07 2020 mips
Mode: Gateway, Wifi disabled, Wireguard Endpoint for external VPS, connected via DHCP WAN to WRT1900ACS v2, Keep Alive reboot 6:05 in the morning
Reset: No
Status: 0.5h up, ok.