Joined: 08 May 2018 Posts: 14221 Location: Texas, USA
Posted: Tue Jul 21, 2020 17:22 Post subject: New Build - 07-21-2020-r43886
[WARNING]: This thread is only for feedback on this beta release for developers and the community's benefit.
DO NOT flash this beta release unless you understand the risks involved and specific device recovery methods.
Avoid discussions! Create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Notes:
• CVE-2019-14899 VPN fix (applicability depends on VPN setup) and GUI toggle. 6920, 6928, 6931, 6932 (WIP 7040)
• In-kernel Samba has been implemented this year and default min/max versions have changed 6954, 6957, with WSD support.
• VAP issue is fixed! For any Wireless Mode, create a VAP and both ath0/ath1 should now function properly.
• Local DNS option removed from Services->DNSMasq in changesets 43080 and 43081; ref: #7092
• DHCP and DNS help (English) updated in 43083; ref: #7091
• WireGuard 1.0.20200623: PBR, Kill Switch, Inbound Firewall, Naming of Peers, Status, Key, Guides. Thanks egc!
Issues:
• There may be remaining issues for Samba (for example NTFS), with frequent updates.
Important:
• If reporting issues provide applicable info: 'dmesg', 'cat /tmp/var/log/messages', syslog/serial output, strace etc.
• For firewall issues provide 'iptables -L', 'iptables -t nat -L' and the /tmp/.ipt file.
• Search existing SVN tickets before opening a new one. Before reporting, reset and manually setup (no nvram backup).
• Be sure to include operating and wireless modes (Gateway, AP, CB, etc.) along with relevant configuration information.
Router/Version: Linksys WRT1900ACS v2
Mode: Wireguard "client", DHCP, DNS forwarding through wireguard, custom routes, 2.4 GHz HT40 and 5 GHz VHT80
Reset: No
Status: All working nominally. WG related routes came up quickly after WG was established
Same as previous version, 50% load during idle is still there, but otherwise everything is working.
Mixed mode for Physical Interface ath0 seems to be actually defaulting to Wireless AC mode when at 80mhz channel width, which is fine, but some people might be wary of this, and if they want to run real mixed mode they might want to change that to 40 Mhz. _________________ Router: Linksys WRT3200ACM WLAN0 and 1 have same SSID
88W8964 802.11ac WLAN0 Mode AP VHT80 80MHz Mixed Mode Channel and Extension Channel Auto Extension LL-6
88W8964 802.11ac WLAN1 Mode AP 20 MHz Mixed Mode Channel Auto
SD8887 802.11ac disabled but visible on GUI and CLI
TX Power 18 dBm
Antenna Gain 0 dBi
U-APSD (Automatic Power Save)Enabled
Protection Mode None
RTS Threshold Disabled
Short Preamble Disabled
Short GI Enabled
Single User Beamforming Enabled
Multi User Beamforming Enabled
AP Isolation Disabled
Beacon Interval 100
DTIM Interval 2
WMM Support Enabled
Radar Detection Disabled
ScanList default
Sensitivity Range (ACK Timing) 500 (Default: 500 meters)
Max Associated Clients 256 (Default: 256 Clients)
Minimum Signal for authenticate -128
Minimum Signal for connection -128
Poll Time for signal lookup 10
Amount of allowed low signals 3
Wireless security is WPA2 Personal CCMP-128 only
QAM256 is on
Router: Linksys WRT1900ACSv2
Firmware: DD-WRT v3.0-r43886 std (07/21/20) prev. r43824
Kernel: Linux 4.9.230 #1918 SMP Tue Jul 21 00:48:11 +03 2020 armv7l
Browser: Opera Stable 68.0 (Windows 10 64-bit)
Reset: No
Temperatures: It does not matter (an automatic fan is installed) - always within the range of 59-69°С.
Mode:
DHCP Server
2.4 GHz: AP NG-Mixed, Channel 5, Full 20 MHz, TurboQAM (QAM256) support.
5 GHz: AP AC/N-Mixed, Channel 161+Lower, Wide HT40, Allow Channel Overlapping.
Security: WPA2 Personal CCMP-128 (AES)
NAS via USB:
/dev/sda - Block device, size 931.5GiB, Partition: 1-Ext4, 2-Ext4 , 3-swap.
/dev/sdb - Block device, size 931.5 GiB, Partition: 1-Ext4, 2-swap.
Samba shared: Protocol Version NT 1.0\SMB 3.11
If you share /jffs in Samba, then autostart is not required (sleep 30; stopservice samba3; startservice samba3).
NFS Server shared: Shared the same partitions as in Samba.
Errors:
GUI doesn't have a button Administration->Backup->Backup.
"Bad block" was found in the log:
Code:
Jan 1 03:00:09 LinkSYS kern.info kernel: [ 0.913014] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xf1
Jan 1 03:00:09 LinkSYS kern.info kernel: [ 0.919393] nand: AMD/Spansion S34ML01G2
Jan 1 03:00:09 LinkSYS kern.info kernel: [ 0.923339] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
Jan 1 03:00:09 LinkSYS kern.info kernel: [ 0.930942] pxa3xx-nand f10d0000.flash: ECC strength 16, ECC step size 2048
Jan 1 03:00:09 LinkSYS kern.info kernel: [ 0.938124] Bad block table found at page 65472, version 0x01
Jan 1 03:00:09 LinkSYS kern.info kernel: [ 0.944234] Bad block table found at page 65408, version 0x01
Recent errors appeared during test copying, moving and deleting files on NAS disks; all sections ext4.
Please note that the time of entries in the logs jumps. If it doesn't matter, tell me, I won't report. _________________ Linksys WRT1900ACSv2
Automatically adjustable temperature, always within the range of 59-68°С.
OpenVPN CLIENT seems fine (nordvpn server)
5GHz wpa2 CCMP-128 (AES) Conditional 40MHz Mixed
2.4GHz wpa2 CCMP-128 (AES) Conditional 20MHz N Only
NAS via USB Samba Conditional - Abends with out of memory errors from time to time.
Wifi Stays clean as long as I "keep alive" auto boot every 24 hours